Summary of gpd 503
Page 1
Magne tek gpd 503 technical manual.
Page 2
- i - gpd 503 simplified start-up procedure this procedure will quickly get you up and running by digital operator keypad or user supplied remote operator control. It assumes that the gpd 503 and motor are correctly wired (see pages 1-8 thru 1-15), and start-up is to be performed without any changes...
Page 3
Installation of external run/stop switch and speed potentiometers important: complete the installation and keypad operation instructions before attempting external control. 1. Disconnect power, remove cover, and wait for “charge” light to go out. 2. Refer to the diagram below and connect a switch to...
Page 4
Important: programming is required to set up the drive for operation from external terminals. 6. Replace cover, make sure remote switch s1 is in “stop” position, then apply power. Note that the drive lamp is on. Press drive/program key, noting the drive lamp goes out, indicating drive is in the “pro...
Page 5
- iv - cn-29 50 cn-30 160 cn-31 (4) cn-32 (4) cn-33 (4) cn-34 30 (3) cn-35 2.0 cn-36 0 cn-37 (4) cn-38 150 cn-39 2.0 (4) cn-40 (4) cn-41 100 cn-42 0.3 un-01 n/a n/a un-02 n/a n/a un-03 n/a n/a un-04 n/a n/a un-05 n/a n/a un-06 n/a n/a un-07 n/a n/a un-08 n/a n/a un-09 n/a n/a un-10 n/a n/a sn-22 02 ...
Page 6
-v- horsepower range rated horsepower model input ct (150% ol) vt (125% ol) no. 1 1 ds305 2 2 ds302 3 3 ds306 5 5 ds307 7.5 7.5/10 ds308 2 10 15 ds309 3 15 20 ds310 0 20 25 ds311 v 25 30 ds322 30 40 ds323 40 50 ds2040 40/50 50 gpd503-2l40 50 60 ds2050 60 60 gpd503-2l50 60 75 ds2060 60 75 gpd503-2l60...
Page 7
Section 1. Installation 1.1 general the gpd 503 is a high performance sine-coded pulse width modulated ac motor drive which generates an adjustable voltage/frequency three phase output for complete speed control of any conventional squirrel cage induction motor. Automatic stall prevention and voltag...
Page 8
1.4 electrical installation all basic interconnections (using the digital operator) are shown in figures 1-3 through 1-6. 1.4.1 main circuit input/output complete wiring interconnections for the main circuit according to tables 1-1 and 1-2, while observing the following: caution use only factory sup...
Page 9
Hp terminal wire size rating terminal symbol screw awg mm2 ds305 l1 (r), l2 (s), l3 (t), –, b1/+, b2, t1 (u), t2 (v), t3 (w), g (e) m4 14 - 10 2 - 5.5 ds302, l1 (r), l2 (s), l3 (t), –, b1/+, b2, t1 (u), t2 (v), t3 (w) m4 14 - 10 2 - 5.5 ds306 g (e) m4 12 - 10 3.5 - 5.5 ds307 l1 (r), l2 (s), l3 (t), ...
Page 10
Drive terminal wire size model no. Terminal symbol screw awg mm2 ds313, ds304, l1 (r), l2 (s), l3 (t), –, b1/+, b2, t1 (u), t2 (v), t3 (w), g (e) m4 14 - 10 2 - 5.5 ds314 ds315 l1 (r), l2 (s), l3 (t), –, b1/+, b2, t1 (u), t2 (v), t3 (w) m4 14 - 10 2 - 5.5 g (e) m5 12 - 10 3.5 - 5.5 ds316 l1 (r), l2 ...
Page 11
1-2.3 drive terminal wire size model no. Terminal symbol screw awg mm2 ds5003, l1 (r), l2 (s), l3 (t), –, b1/+, b2, t1 (u), t2 (v), t3 (w) m4 14 - 10 2 - 5.5 ds5004 g (e) m4 14 - 10 2 - 5.5 ds5006 l1 (r), l2 (s), l3 (t), –, b1/+, b2, t1 (u), t2 (v), t3 (w) m4 14 - 10 2 - 5.5 g (e) m5 14 - 10 2 - 5.5...
Page 12
1-2.4 section a. 230v terminal function 1 hp 3 to 40 hp l1 (r) three phase main circuit input power supply l2 (s) 200 / 208 / 220v at 50 hz; 200 / 208 / 220 / 230v at 60 hz l3 (t) t1 (u) three phase ac output to motor t2 (v) 0v to max. Input voltage level t3 (w) l1 (r) power for heat sink fan l2 (s)...