1. DL manuals
  2. Magnum
  3. Lawn and Garden Equipment
  4. 24N808
  5. Operation

Magnum 24N808 Operation

Summary of 24N808

  • Page 1

    313034g en operation lts 15, lts 17, prolts 17 and prolts 19 airless sprayers - for portable spray applications of architectural paints and coatings. For professional use only- models 257060, 257065, 24n906, 24n808 3000 psi (21 mpa, 207 bar) maximum working pressure see page 2 for model and series i...

  • Page 2: Specifications

    Specifications 2 313034g specifications this equipment is not intended for use with flammable or combustible materials used in places such as cabinet shops or other “factory”, or fixed locations. If you intend to use this equipment in this type of application, you must comply with nfpa 33 and osha r...

  • Page 3: Warnings

    Warnings 313034g 3 warnings the following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-spe...

  • Page 4: Warning

    Warnings 4 313034g fire and explosion hazard flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • do not spray flammable or combustible materials near an open flame or sources of ignition such as cig- arettes, motors, and electri...

  • Page 5: Warning

    Warnings 313034g 5 equipment misuse hazard misuse can cause death or serious injury. • do not operate the unit when fatigued or under the influence of drugs or alcohol. • do not exceed the maximum working pressure or temperature rating of the lowest rated system com- ponent. See technical data in al...

  • Page 6: Warning

    Warnings 6 313034g toxic fluid or fumes hazard toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swal- lowed. • read msds’s to know the specific hazards of the fluids you are using. • store hazardous fluid in approved containers, and dispose of i...

  • Page 7: Installation

    Installation 313034g 7 installation grounding and electric requirements sprayer must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for electrical current due to static build up or in the event of a short circuit. • the 120 vac sprayers require a 120...

  • Page 8: Component Identification

    Component identification 8 313034g component identification a airless spray gun dispenses fluid. B power switch turns sprayer on and off. C pressure control knob increases (clockwise) and decreases (counter-clockwise) fluid pressure in pump, hose, and spray gun. C1 setting indicator to select functi...

  • Page 9

    Component identification 313034g 9 j e d x b w f c g l h q r a s t ti9669a ti11987a m ti9368b c1 ti9346a ti9670a f1 u ti9724a ti11988a v (sg2/sg3).

  • Page 10: Operation

    Operation 10 313034g operation trigger lock always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped. Pressure relief procedure follow this pressure relief procedure whenever you stop spraying and before cleaning, chec...

  • Page 11: Setup

    Setup 313034g 11 setup 1. Unscrew tip and guard assembly from gun. 2. Uncoil hose and connect one end to gun. Use two wrenches to tighten securely 3. Connect other end of hose to sprayer. Note: if hose is already connected, make sure connec- tions are tight. 4. Turn off power switch. 5. Turn pressur...

  • Page 12

    Setup 12 313034g 1. Make sure the power switch is off and the sprayer is unplugged. 2. Separate prime tube (smaller) from suction tube (larger). 3. Place prime tube in waste pail. 4. Submerge suction tube in water or flushing solvent. 5. Turn prime/spray valve to prime. 6. Plug sprayer in a grounded...

  • Page 13: Spraying Techniques

    Setup 313034g 13 install tip and guard on gun 1. Engage trigger lock. 2. Verify tip and guard parts are assembled in order shown. 3. Screw tip and guard assembly on gun. Tighten retaining nut. 4. Make sure spray tip is pointing forward in spray posi- tion. Spraying techniques preventing excessive ti...

  • Page 14: Unclogging Spray Tip

    Setup 14 313034g unclogging spray tip to avoid fluid splash-back: • never pull gun trigger when arrow-shaped handle is between spray and unclog positions. • tip must be pushed all the way into guard. 1. To unclog tip obstruction, engage trigger lock. 2. Point arrow-shaped handle backward to unclog p...

  • Page 15: Tip Selection

    Setup 313034g 15 tip selection selecting tip hole size tips come in a variety of hole sizes for spraying a range of fluids. Your sprayer includes an 0.015 in (0.38 mm) tip for use in most spraying applications. Use the following table to determine the range of recommended tip hole sizes for each flu...

  • Page 16

    Setup 16 313034g understanding tip number the last three digits of tip number (i.E.: 221413) contain information about hole size and fan width on surface when gun is held 12 in. (30.5 cm) from surface being sprayed. Reversible tip selection chart example: for an 8 to 10 in. (203 to 254 mm) fan width...

  • Page 17: Triggering Gun

    Getting started with basic techniques 313034g 17 getting started with basic techniques use a piece of scrap cardboard to practice these basic spraying techniques before you begin spraying the sur- face. • hold gun 12 in. (30 cm) from surface and aim straight at surface. Tilting gun to direct spray a...

  • Page 18: Shutdown And Cleaning

    Shutdown and cleaning 18 313034g shutdown and cleaning pail flushing • for short term shutdown periods (overnight to two days) refer to short term storage, page 23. • for flushing after spraying oil-based coatings, use compatible oil-based flushing fluid or mineral spirits. Read priming and flushing...

  • Page 19

    Shutdown and cleaning 313034g 19 12. To preserve paint in hose: a. Point gun into paint pail. B. Unlock gun trigger lock. C. Pull and hold gun trigger. D. Turn prime/spray valve to spray. E. Turn power switch on. F. Continue to hold gun trigger until you see paint diluted with flushing fluid startin...

  • Page 20: Power Flush

    Shutdown and cleaning 20 313034g power flush power flushing is a faster method of flushing. It can only be used after spraying water-based coatings. 1. Relieve pressure, page 10. 2. Remove tip and guard assembly from gun and place in waste pail. 3. Place empty waste and paint pails side by side. 4. ...

  • Page 21

    Shutdown and cleaning 313034g 21 note: step 16 is for returning paint in hose back to paint pail. One 50-ft (15-m) hose holds approximately 1-quart (1-liter) of paint. 16. To preserve paint in hose: a. Point gun into paint pail. B. Unlock gun trigger lock. C. Pull and hold gun trigger. D. Turn prime...

  • Page 22: Cleaning Instaclean

    Shutdown and cleaning 22 313034g cleaning instaclean ™ fluid filter (prolts sprayers only) the instaclean fluid filter prevents particles from entering paint hose. After each use, remove and clean it to insure peak performance. 1. Relieve pressure, page 10. 2. A. Disconnect airless spray hose (a) fr...

  • Page 23: Storage

    Storage 313034g 23 storage short term storage (up to 2 days) 1. Relieve pressure, page 10. 2. Leave suction tube and prime tube in paint pail. 3. Cover paint pail and hoses tightly with plastic wrap. 4. A. Engage trigger lock. B. Leave gun attached to hose. C. If you have not already cleaned them, r...

  • Page 24

    Storage 24 313034g 4. Turn pressure control knob clockwise until the pump turns on. 5. When storage fluid comes out of prime tube (5-10 seconds) turn power switch off. 6. Turn prime/spray valve to spray to keep storage fluid in sprayer during storage. Ti9343a ti9345a ti2018a.

  • Page 25: Stowing Sprayer

    Storage 313034g 25 stowing sprayer 1. Screw inlet screen onto suction tube. 2. Coil hose. Leave it con- nected to sprayer. Wrap hose around hose wrap bracket. 3. Secure a plastic bag around suction tube to catch any drips. 4. Store sprayer indoors. Notice before storing sprayer make sure all water i...

  • Page 26: Maintenance And Service

    Maintenance and service 26 313034g maintenance and service caring for sprayer keep sprayer and all accessories clean and in good working order. To avoid overheating motor, keep vent holes in shroud clear for air flow. Do not cover sprayer while spraying. Paint hoses check hose for damage every time ...

  • Page 27: Troubleshooting

    Troubleshooting 313034g 27 troubleshooting check everything in this troubleshooting table before you bring the sprayer to a graco/m agnum authorized service center. Problem cause solution power switch is on and sprayer is plugged in, but motor does not run, and pump does not cycle. Pressure is set a...

  • Page 28

    Troubleshooting 28 313034g pump does not prime. Prime/spray valve is in spray posi- tion. Turn prime/spray valve to prime position (pointing down). Inlet screen is clogged or suction tube is not immersed. Clean debris off inlet screen and make sure suction tube is immersed in fluid. Pump was not pri...

  • Page 29

    Troubleshooting 313034g 29 pump cycles but does not build up pressure. Pump is not primed. Prime pump. Inlet screen is clogged . Clean debris off inlet screen and make sure suction tube is immersed in fluid. Suction tube is not immersed in paint. Make sure suction tube is immersed in paint. Suction ...

  • Page 30

    Troubleshooting 30 313034g pressure is set at maximum but can- not achieve a good spray pattern. Reversible spray tip is in unclog position. Rotate arrow-shaped handle on spray tip so it points forward in spray position, page 14. Spray tip is too large for sprayer. Select smaller spray tip. Spray ti...

  • Page 31

    Troubleshooting 313034g 31 cannot trigger spray gun. Spray gun trigger lock is locked. Rotate trigger safety lever to unlock trigger lock, page 10. Paint is coming out of pressure con- trol switch. Pressure control switch is worn. Take sprayer to graco/m agnum authorized service center. Prime/spray ...

  • Page 32: Technical Data

    Technical data 32 313034g technical data m agnum lts 15 m agnum lts 17 working pressure range 0-3000 psi (0-21 mpa, 0-207 bar) 0-3000 psi (0-21 mpa, 0-207 bar) electric motor 9.0a (open frame, universal) 9.0a (open frame, universal) operating horsepower 1/2 5/8 maximum delivery (with tip) 0.27 gpm (...

  • Page 33

    Technical data 313034g 33 m agnum prolts 17 m agnum prolts 19 working pressure range 0-3000 psi (0-21 mpa, 0-207 bar) 0-3000 psi (0-21 mpa, 0-207 bar) electric motor 5.8a (open frame, permanent magnet dc) 9.4a (open frame, permanent magnet dc) operating horsepower 3/4 7/8 maximum delivery (with tip)...

  • Page 34: Graco Standard Warranty

    All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.Graco.Com/patents. Original instructions . This manual contains en...

  • Page 35: Prolts 19 Airless Sprayers

    313036h en repair and parts lts 15, lts 17, prolts 17 and prolts 19 airless sprayers - for portable spray applications of architectural paints and coatings - lts 15 & lts 17 models only: use water-based or mineral spirit-type materials only. Do not use materi- als having flash points lower than 70° ...

  • Page 36: Specifications

    Specifications 2 313036h specifications this equipment is not intended for use with flammable or combustible materials used in places such as cabinet shops or other “factory”, or fixed locations. If you intend to use this equipment in this type of application, you must comply with nfpa 33 and osha r...

  • Page 37: Warnings

    Warnings 313036h 3 warnings the following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. Refer back to these warnings. Additional, product ...

  • Page 38: Warning

    Warnings 4 313036h fire and explosion hazard flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: • do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors, and electrica...

  • Page 39: Warning

    Warnings 313036h 5 equipment misuse hazard misuse can cause death or serious injury. • do not operate the unit when fatigued or under the influence of drugs or alcohol. • do not exceed the maximum working pressure or temperature rating of the lowest rated system com- ponent. See technical data in al...

  • Page 40: Warning

    Warnings 6 313036h toxic fluid or fumes hazard toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swal- lowed. • read msdss to know the specific hazards of the fluids you are using. • store hazardous fluid in approved containers, and dispose of it...

  • Page 41: Notes

    Notes 313036h 7 notes.

  • Page 42: Component Identification

    Component identification 8 313036h component identification a airless spray gun sprays fluid. B power switch turns sprayer on and off. C pressure control knob increases (clockwise) and decreases (counter-clockwise) fluid pres- sure in pump, hose, and spray gun. C1 setting indicator to select functio...

  • Page 43

    Component identification 313036h 9 j e d x b k w f c g l h q r a s t ti9669a ti11988a ti11987a m ti9368b c1 v ti9346a ti9670a f1 u aa ti9724a n prolts series a shown sg2/sg3.

  • Page 44: Installation

    Installation 10 313036h installation grounding and electric requirements sprayer must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for electrical current due to static build up or in the event of a short circuit. • this sprayer requires a 120 vac, ...

  • Page 45: Operation

    Operation 313036h 11 operation see operation manual 312001 for basic information on sprayer set-up, flushing, and storage. Trigger lock always engage the trigger lock when you stop spraying to prevent the gun from being triggered accidentally by hand or if dropped or bumped. Pressure relief procedur...

  • Page 46: General Repair Information

    General repair information 12 313036h general repair information • keep all screws, nuts, washers, gaskets, and electri- cal fittings removed during repair procedures. These parts usually are not provided with replacement kits. • test repairs after problems are corrected. • if sprayer does not opera...

  • Page 47: Basic Troubleshooting

    Basic troubleshooting 313036h 13 basic troubleshooting check everything in this basic troubleshooting table before you bring the sprayer to a graco/m agnum authorized ser- vice center. Problem cause solution power switch is on and sprayer is plugged in, but motor does not run, and pump does not cycl...

  • Page 48

    Basic troubleshooting 14 313036h pump does not prime. Prime/spray valve is in spray position. Turn prime/spray valve to prime position (pointing down). Inlet screen is clogged or suction tube is not immersed. Clean debris off inlet screen and make sure suction tube is immersed in fluid. Pump was not...

  • Page 49

    Basic troubleshooting 313036h 15 pump cycles but does not build up pressure. Prime/spray valve in prime posi- tion (pointing down). Turn prime/spray valve to spray position (pointing forward). Pump is not primed. Prime pump, see operation manual 313034. Inlet screen is clogged or suction tube is not...

  • Page 50

    Basic troubleshooting 16 313036h pressure is set at maximum but cannot achieve a good spray pattern. Spray tip is clogged. Unclog spray tip, see operation manual 313034. Reversible spray tip is in unclog position. Rotate arrow-shaped handle on spray tip so it points forward on gun. Spray tip is too ...

  • Page 51

    Basic troubleshooting 313036h 17 prime/spray valve actuates automatically relieving pressure through prime tube. System is over pressurizing. Take sprayer to graco/m agnum authorized service center. Paint leaks down outside of pump. Pump packings are worn. Take sprayer to graco/m agnum authorized se...

  • Page 52: Advanced Troubleshooting

    Advanced troubleshooting 18 313036h advanced troubleshooting see basic troubleshooting first, page 13 for problems that are more easily remedied. General problem: motor does not operate specific problem cause solution power switch is on and sprayer is plugged in; pump does not cycle. See basic troub...

  • Page 53

    Advanced troubleshooting 313036h 19 basic electrical problems. Motor overheated. Allow motor to cool for 45 minutes. Retry. Electrical outlet is damaged. Reset building circuit breaker or replace fuse. Try another outlet. Check electric supply with volt meter. Meter must read 85 to 130v ac. If volta...

  • Page 54

    Advanced troubleshooting 20 313036h sprayer wiring problems note: remove enclosure mounting screws and pull enclosure away from drive housing. Take care not to pull on leads from electrical cord and power switch. Sprayer power cord dam- aged. Unplug sprayer power cord. Disconnect black power cord wi...

  • Page 55

    Advanced troubleshooting 313036h 21 general problem: circuit breaker is tripping specific problem cause solution building circuit breaker opens as soon as sprayer is turned on. Note: remove enclosure mounting screws and pull enclosure away from drive housing. Take care not to pull on leads from elec...

  • Page 56

    Advanced troubleshooting 22 313036h general problem: erratic motor operation specific problem cause solution sprayer quits after running for 5 to 10 minutes building circuit is overloaded. Remove other loads from building circuit or find another circuit that has less load. See ground- ing and electr...

  • Page 57

    Advanced troubleshooting 313036h 23 general problem: low or fluctuating output specific problem cause solution pump cycles, but output is low or surging. See basic troubleshooting, page 13. Worn or obstructed inlet and outlet valves. Check for worn pump valves as follows: prime sprayer with paint. T...

  • Page 58

    Advanced troubleshooting 24 313036h motor runs and pump cycles, but pressure does not build up. Intake valve or outlet valve is not seating properly. Remove and clean inlet valves and outlet valves. Replace if necessary. See list of kits, page 28. Pump packings are worn or damaged. Check for leaking...

  • Page 59

    Motor diagnostics (lts 15 and lts 17) 313036h 25 motor diagnostics (lts 15 and lts 17) if motor diagnostics reveal a damaged motor or if motor brushes are shorter than 1/4 in. (6.4 mm) replace the motor using motor kit, page 28. Setup 1. Unplug power cord and relieve pressure, page11. 2. Remove encl...

  • Page 60

    Pressure control switch diagnostics 26 313036h pressure control switch diagnostics lts 15, lts 17, prolts 17 and prolts 19 if pressure control switch diagnostics reveal a damaged pressure control, replace it with the correct pressure con- trol switch kit, see page 28. Lts 15 and lts 17 sprayers have...

  • Page 61: Pump Diagnostics

    Control board diagnostics (prolts 17 and prolts 19) 313036h 27 control board diagnostics (prolts 17 and prolts 19) note: check for motor problems before replacing control board. A damaged motor may burn out a good control card. Check for a damaged control board or pressure control switch as follows:...

  • Page 62: List Of Kits (Series A)

    List of kits (series a) 28 313036h list of kits (series a) kit number models kit description 289107 all autoprime 16e829 lts 15, lts 17 control board 288705 prolts 17 control board 288900 prolts 19 control board 244035 all drain tube diffuser 16e830 lts 15 enclosure (includes labels and screws) 16e8...

  • Page 63: List of Kits (Series B, C)

    List of kits (series b, c) 313036h 29 list of kits (series b, c) kit number models kit description 289107 all autoprime 16e829 lts 15, lts 17 control board 244035 all drain tube diffuser 16e830 lts 15 enclosure (includes labels and screws) 16e831 lts 17 enclosure (includes labels and screws) 16e833 ...

  • Page 64: Parts

    Parts 30 313036h parts lts 15 model 257060 (series a) ▲ replacement warning labels, tags and cards are available at no cost. Ref part description qty 1 289682 kit, housing cover, includes 1a, 1b 1 1a 120724 screw 4 1b ▲ 15u408 label, magnum lts 15, front 1 7 244266 kit, pressure control, includes 7a...

  • Page 65

    Parts 313036h 31 lts 15 model 257060 (series a) 1a 1 7 17 14b 32a 32 31 30 16 24 25 23 22 29 38 39 39 37 33 34 35 36 35 26 66 1b 7b 14a 14 7a ti11318a 29b 29a.

  • Page 66

    Parts 32 313036h lts 15 model 257060 (series a) 68 41 67 41 40 51 44 43 47a 47 41b 41a 71 72 67a 86 67b 70 85 85a 84 ti11319a.

  • Page 67: Parts

    Parts 313036h 33 parts lts 15 model 257060 (series b, c) ▲ replacement warning labels, tags and cards are available at no cost. * 16e846 kit, repair, pump. Complete is available. (it includes items 17, 22, 23, 24, 25, 29 and 30) ref part description qty 1 16e833 kit, housing cover, includes 1a, 1b 1...

  • Page 68

    Parts 34 313036h lts 15 model 257060 (series b, c) 29 29c 29b 29a 17 15 30 16 18 31 7a 7b 32 32a 1 1a 37 23 24 25 1b 7 39 33 38 35 34 36 35 22 43 14 ti17271a.

  • Page 69

    Parts 313036h 35 lts 15 model 257060 (series b, c) 44 72 41 40 41b 41a 68 51 47 43 67 85 85a 84 67b 67a 41 86 71 70 47b 41b 47a ti17270b.

  • Page 70

    Parts 36 313036h lts 17 model 257065 (series a) ▲ replacement warning labels, tags and cards are available at no cost. Ref part description qty 1 289682 kit, housing cover, includes 1a, 1b 1 1a 120724 screw 4 1b ▲ 15u409 label, magnum lts 17, front 1 7 244267 kit, pressure control, includes 7a, 7b 1...

  • Page 71

    Parts 313036h 37 lts 17 model 257065 (series a) 25 30 31 32a 16 32 66 14b 29 22 23 24 1a 38 7 7a 1 17 26 33 35 34 35 36 39 62 37 1b 32a 7b 14a 14 ti11320a 29a 29b.

  • Page 72

    Parts 38 313036h lts 17 model 257065 (series a) 41 41a 41b 71 57 58 68 43 44 40 47a 41c 41d 52 72 53 60 56 51 47 55 54 67 41 86 70 67b 67a 85 85a 84 ti11989a.

  • Page 73

    Parts 313036h 39 lts 17 model 257065 (series b, c) ▲ replacement warning labels, tags and cards are available at no cost. * 16e846 kit, repair, pump complete is available. (it includes 17, 22, 23, 24, 25, 29 and 30.) ref part description qty 1 16e833 kit, housing cover, includes 1a, 1b 1 1a 120724 s...

  • Page 74

    Parts 40 313036h lts 17 model 257065 (series b, c) 53 40 44 86 41a 56 41 41c 55 54 60 67b 62 47 41 70 ti11321b 41d 67a 84 41b 67 85 85a 71 43 47a 58 57 68 72 51.

  • Page 75

    Parts 313036h 41 lts 17 model 257065 (series b, c) 36 ti11989a 35 35 34 24 16 38 37 33 1a 7a 18 68 32 43 25 1b 62 32a 30 31 7 7b 17 32a 23 22 29 29b 29a 29c 1 15 14.

  • Page 76

    Parts 42 313036h prolts 17, prolts 19 models 257070, 257080 (series a) ▲ replacement warning labels, tags, and cards are available at no cost. Ref part description qty 1 15j632 leg 2 2 15j633 support, frame 2 3 15j641 pull rod 1 4 15j675 spacer, frame 4 5 15j678 bracket 2 6 15j691 axle pin 2 7 15j69...

  • Page 77

    Parts 313036h 43 prolts 17, prolts 19 models 257070, 257080 (series a) 45 45d 116 66 45a 44 47 85 59 59a 68 58 52 56 50 49 55 51 39 40 34 32 34 33 30 29 53 31 63b 63 46 62b 67 67c 67b 67a 57 23 110 41 81 45b 45c 85 68a 63a 42 37 63d 63c 62a 35 62 ti11991a.

  • Page 78

    Parts 44 313036h prolts 17, prolts 19, models 257070, 257080 (series a) 9 3 27 15 12 75 20 81 18 23 83 16 17 28 8 5 25 82 75 8 19 81 21 76 6 4 10 1 7 2 9 22 4 ti9504b.

  • Page 79

    Parts 313036h 45 prolts 17, prolts 19 models 24n906, 24n808 (series a) ref part description qty 1 262012 kit, left leg, includes 7, 8 1 2 262014 kit, right leg, includes 7, 8 2 5 16f372 bracket 2 6 15r602 axle 2 7 15j695 tube cap 2 8 15j699 tube cap 2 16 16h350 hose rack 1 17 16h353 cart handle 1 19...

  • Page 80

    Parts 46 313036h prolts 17, prolts 19, models 24n906, 24n808 (series a) 45b 45a 45c 45d 85 45 44 47 85 68a 42 46 59 59a 52 58 67 67c 67a 63d 67b 57 23 110 63 63a 63b 31 53 29 32 35 41 30 33 34 62b 62a 62 63c 50 49 55 37 51 39 40 34 81 56 68 ti11991b.

  • Page 81

    Parts 313036h 47 prolts 17, prolts 19 models 24n906, 24n808 (series a) ti11991b 17 28 16 83 8 82 21 76 6 81 5 1 2 7.

  • Page 82: Wiring Diagrams

    Wiring diagrams 48 313036h wiring diagrams lts 15, lts 17 models 257060, 257065 (series a) 7)2).'$)!'2!- 7()4% "/!2$7)2% !54/02)-% 0/7%2#/2$ ",!#+7)2% ",!#+ -/4/2 ,%!$ 0/7%2#/2$ 7()4%7)2% ",!#+ -/4/2 ,%!$ !&53% 0/7%2#/2$ '2%%.7)2% #(!33)3 '2/5.$ /./&& 37)4#( 02%3352% 37)4#( thermal switch 1 1 when a...

  • Page 83: Wiring Diagrams

    Wiring diagrams 313036h 49 wiring diagrams lts 15, lts 17 models 257060 (series b, c), 257065 (series b) wiring diagram white board wire auto prime powercord black wire powercord white wire 10a fuse powercord green wire chassis ground on/off switch pressure switch ti15763a ref 67a.

  • Page 84

    Wiring diagrams 50 313036h prolts 17 models 257070, 24n906 series a prolts 19 models 257080, 24n808 series a #(!33)3'2/5.$ 7(4 '2. ",+ ",+ /./&& 37)4#( #/.42/,"/!2$ 7)2).'$)!'2!- 0/7%2#/2$ 02%3352% 37)4#( !54/02)-% 2%& * * * * , , , , 7(4 ti9505a.

  • Page 85: Technical Data

    Technical data 313036h 51 technical data m agnum lts 15 m agnum lts 17 working pressure range 0-3000 psi (0-21 mpa, 0-207 bar) 0-3000 psi (0-21 mpa, 0-207 bar) electric motor 9.0a (open frame, universal) 9.0a (open frame, universal) operating horsepower 1/2 5/8 maximum delivery (with tip) 0.27 gpm (...

  • Page 86

    Technical data 52 313036h m agnum 257070 prolts 17 (series a) m agnum (24n906) prolts 17 (series a) working pressure range 0-3000 psi (0-21 mpa, 0-207 bar) 0-3000 psi (0-21 mpa, 0-207 bar) electric motor 5.8a (open frame, permanent magnet dc) 5.8a (open frame, permanent magnet dc) operating horsepow...

  • Page 87

    Technical data 313036h 53 m agnum (257080) prolts 19 (series a) m agnum (24n808) prolts 19 (series a) working pressure range 0-3000 psi (0-21 mpa, 0-207 bar) 0-3000 psi (0-21 mpa, 0-207 bar) electric motor 9.4a (open frame, permanent magnet dc) 9.4a (open frame, permanent magnet dc) operating horsep...

  • Page 88: Graco Standard Warranty

    All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.Graco.Com/patents. Original instructions . This manual contains en...