Magnum Dynalab MD 301 Instruction Manual

Manual is about: HYBRID INTEGRATED AMPLIFIER

Summary of Dynalab MD 301

  • Page 1

    Magnum dynalab md 301 hybrid integrated amplifier instruction manual.

  • Page 2

    - - 2 table of contents table of contents dear valued customer ......................................................... 2 dear valued customer .............................................................................................. 3 unpacking your md 301 hybrid integrated amplifier ............

  • Page 3

    - - 3 dear valued customer thank you for choosing the magnum dynalab md 301 hybrid integrated amplifier . Great care has been given to the design, manufacturing and selection of components for the md 30 1 hybrid integrated amplifier . This complete process insures optimum listening enjoyment for man...

  • Page 4

    - - 4 unpacking your md 301 hybrid integrated amplifier carefully inspect all sides of the shipping carton for damage. If there are marks or holes in the carton make note of the location in relation to the unit inside. Any obvious dents or scuff marks should alert you to the possibility of damage. C...

  • Page 5

    - - 5 setting up the md 301 hybrid integrated amplifier 1. Position the unit away from any spot which may have extremes in temperatures. 2. Place the unit on a very rigid surface capable of holding 75 pounds (34 kg). 3. The heat sinks located inside the unit are used to keep the unit at a safe opera...

  • Page 6

    - - 6 3. With volume set to zero, power up the source, initialize the playback, and slowly adjust volume to desired level..

  • Page 7

    - - 7 set up the md 301 hyrbid integrated amplifier with an external home theater processor the md 301 hybrid integrated amplifier is equipped with a unity gain input (a3/ssp mode input on the pre-amplifier section). This is a switchable input, meaning the input can be used as a normal pre-amplifier...

  • Page 8

    - - 8 optional digital audio converter (d.A.C) the digital audio converter (d.A.C.) provides an additional usb, and two (2) coaxial inputs or one optical and one rca in the back of the md 301 hybrid integrated amplifier. 1. Connect an external source to the usb, or either of the coaxial inputs. 2. S...

  • Page 9

    - - 9 control/display functions 1. Power button-turns on main power 2. Mute –turns audio output off or back on 3. Input - sequentially moves through the inputs on the rear of the md 301 4. Volume control – the digitally controlled precision volume control allows you to vary the volume from 0-99. Nor...

  • Page 10

    - - 10 diagram of md 301 hybrid integrated amplifier.

  • Page 11

    - - 11 trouble shooting problem possible cause possible solution no sound • power cord disconnected • power off at source • fuse blown • interconnect not properly installed • preamp set to wrong source • power amp off • connect power cord • check ac source • check rear panel fuse • check installatio...

  • Page 12

    - - 12 specifications power output audio frequency response (+/-0.1db) signal to noise ratio total harmonic distortion class of operation input impedance output impedance after volume control inputs outputs input sensitivity fully balanced amplifier design safety diagnostic system dynamic headroom d...

  • Page 13

    - - 13 safety sheet important safety instructions 1. Keep these instructions 2. Heed all warnings 3. Follow all instructions 4. Do not use this apparatus in water 5. Clean only with dry cloth 6. Do not block any ventilation openings, install in accordance with the manufacturer’s instructions. 7. Do ...

  • Page 14

    - - 14 limited warranty register your product at www.Magnumdynalab.Com magnum dynalab ltd. Herein referred to as the “manufacturer” guarantees this product to be free of defect in both material and workmanship and agrees to remedy any such defect or replace any defective component at no charge for a...

  • Page 15

    - - 15 cover or faceplate, no user serviceable parts inside. Refer servicing to qualified service personnel..