Summary of MD 107T
Page 1
Magnum dynalab md 107t/107tr analog fm tuner instruction manual.
Page 2
- 2 - table of contents a message from the president 3 unpacking your 107t 4 setting up your md 107t 5 controls and functionality 6 displays and meters 7 checking out your md 107t 8 tuner remote (optional) 9 rc6 remote image 10 troubleshooting 11 reception techniques 12 antenna cabling: 12 types of ...
Page 3
- 3 - a message from the president thank you for choosing the magnum dynalab “ md 107t ” fm tuner. Great care has been given in the design, manufacturing and selection of components for the “ md 107t” fm tuner. This complete process will insure that your listening experience will be optimized for ye...
Page 4
- 4 - unpacking your 107t carefully inspect all sides of the shipping carton for damage. If there are marks or holes in the carton make note of the location in relation to the unit inside. Any obvious dents or scuff marks should alert you to the possibility of damage. Carefully remove the md 107t fr...
Page 5
- 5 - setting up your md 107t 1. Place your tuner the shortest distance possible from your pre-amplifier/ integrated amplifier, being careful to avoid areas that may cause extreme temperatures. 2. Connect your tuner to the pre-amplifier, using cables/ inter-connects that are consistent with the rest...
Page 6
- 6 - a d c b e f controls and functionality a. Power – turns the power (ac) on and off to your tuner, with the optional remote system this switch must be left in the “off” position. B. Mute – in the “on” position, a limit is now placed on your tuner. While scaling up and down the fm dial, weak stat...
Page 7
- 7 - displays and meters h. Signal stength– this meter readout indicates the amount of signal the tuner is receiving, the higher the better. This will never read “100”. I. Multi-path/signal meter - this meter indicates the amount of multi-path, the lower the reading the better. J. Frequency/input d...
Page 8
- 8 - checking out your md 107t 1. Place your power switch to the “on” position (a on diagram). This should turn on your tuner’s meter lights and frequency display. 2. Place your stereo/mono switch (d on diagram) to the stereo setting. 3. Place your bandwidth switch (e on diagram) to bw1. 4. Place y...
Page 9
- 9 - tuner remote (optional) if your tuner was ordered with the rc6 “precision remote system”, here are the operating instructions. 1. The power switch should be off on the front panel of the tuner 2. Using the remote handheld, push the red “tuner” button. You will see the tuner turn on. 3. To tune...
Page 10
- 10 - rc6 remote.
Page 11
- 11 - troubleshooting problem possible cause possible solution no sound, meter lights are not on • power cord disconnected • power off at source • connect power cord • check ac source no sound, meter lights are on • interconnect not properly installed • preamp set to incorrect source • power amplif...
Page 12
- 12 - no sound from usb • not compatible • signal not receiving • restart your computer or program • if using a mac, you must go to “system preferences”, “sound” and select “usb dac” reception techniques antenna cabling: the lead-in cable from the antenna is often the weakest link in the fm system....
Page 13
- 13 - if multi-path is a reception problem try laying the antenna down in the horizontal plane rather than the vertical plane. This type of antenna can be used indoors or outdoors, but regardless of whether it is installed indoors or outdoors the higher that you can put it the better it will perfor...
Page 14
- 14 - product specifications usable sensitivity- mono – 0.7 uv 9.0 dbf 50 db quieting – mono – 2.0 uv 9.9 dbf 50 db quieting – stereo – 2.3 uv 25.0 dbf capture ratio – 1.5 db image rejection – 110.0 db signal to noise ratio – 80.0 db alternate channel – wide – 40.0 db alternate channel – narrow - 7...
Page 15
- 15 - safety sheet important safety instructions 1. Keep these instructions 2. Heed all warnings 3. Follow all instructions 4. Do not use this apparatus in water 5. Clean only with dry cloth 6. Do not block any ventilation openings, install in accordance with the manufacturer’s instructions. 7. Do ...
Page 16
- 16 - limited warranty register your product at www.Magnumdynalab.Com magnum dynalab ltd. Herein referred to as the “manufacturer” guarantees this product to be free of defect in both material and workmanship and agrees to remedy any such defect or replace any defective component at no charge for a...