Summary of MI-16150
Page 1
Model no.: mi-16150 operating manual stop start.
Page 2: Table of Contnets
Table of contnets table of contents ________________________________________________ safety rules ____________________________________________________ specifications __________________________________________________ instructions for operations _________________________________________ tilting the t...
Page 3: Safety Rules
Safety rules read carefully before operating the machine 1. Learn the machine’s applications and limitations, as well as the specific potential hazards particular to this machine. Follow available safety instructions and safety rules carefully. 2. Keep working area clean and be sure adequate lightin...
Page 4: Specifications
Specifications model mi-16150 table size (l x w) 616 x 616 mm table tilt 0 ~ 45° spindle speed 1725rpm oscillations 59/min oscillation stroke 39 mm sanding sleeve length 150 ~ 230 mm max. Workpiece height 55 ~ 160 mm dust port diameter 100 mm motor 1hp table height 990 mm overall (l x w x h ) 616 x ...
Page 5: Instructions For Operations
Instructions for operations 1. Select spindle that is smaller than the curve to be sanded. 2. Use an insert plate that comes closest to the spindle without touching it. 3. Make sure that spindle is properly positioned in taper sleeve socket. With the wrench provided , tighten the nut. Note: never ov...
Page 6: Tilting The Table
Tilting the table 1. Loosen the two table lock knobs (a), located under the table at both sides of the machine 2. Tilt the table forward to the desired angle with your hands. 3. An angle scale is provided at the right side of the trunnion to indicate the degree of table tilt. 4. Tighten the two tabl...
Page 7: Mounting Spindle Drum
Mounting spindle drum 1. Disconnect the sander from the power source. 2. Select the proper diameter of spindle drum. 3. Clean the taper part of the spindle drum before mounting it into the spindle. 4. Use an open-end wrench to lock the spindle by holding its flat surface. At the same time, use anoth...
Page 8
Selection guide for drum to table insert this machine is furnished with 10 drums. The range of drum diameter is from 1/4” to 4”. If the drum diameter is changed, the table insert needs to be changed to the proper size. The table below shows which table insert to use for various drum diameters. ! War...
Page 9
1. To keep spindle sander in perfect condition, clean machine and attachments at all times. 2. Clean tapered sleeves and tapered socket before use, this will protect spindle sleeves from nicks. 3. Bent sleeves are easily straightened by placing them in the tapered socket and slipping a small pipe ov...
Page 10: Troubleshooting
09 troubleshooting trouble causes correction motor does not run when power switch is turned “on”. 1. Switch is burned out. 2. Connection wire is loose or damaged. 1. Replace the switch. 2. Tighten or replace the wire. Motor does not run at full speed. 1. Power voltage is too low. 2. Motor is damaged...
Page 11: Assembly Diagram
Assembly diagram 10 on off 178 175 170 38 143 143 a 165 150 162 162 56 160 159 87 164 67 86 157 136 39 40 158 163 140 138 139 138 89 161 139 55 56 140 138 66 67 138 20 22 22 21 159 158 157 146 149 150 11 140 66 37 67 28 88 169 170 64 52 154 39 37 135 40 136 136 36 35 40 27 144 32 33 26 47 177 137 14...
Page 12
180 11 4 11 9 94 94 94 94 11 2 122 128 128 95 11 8 11 0 107 95 96 95 96 95 96 104 111 11 3 108 128 133 128 124 130 99 99 99 109 127 93 95 94 94 99 99 99 96 95 101 97 96 105 102 100 106 103 165 98 167 166 11.
Page 13
Parts list for 16150 part no. Ref. No. Description qty mi16150-07 l0000000 power cord 1 mi16150-11 s0400525 key 1 mi16150-18 30101011 oil indicator 1 mi16150-20 30101014 oil seal 1 mi16150-21 c1206206 ball bearing 1 mi16150-22 s0530025 c snap ring 2 mi16150-26 30103014 sleeve 1 mi16150-27 30103015 g...
Page 14
Parts list for 16150 part no. Ref. No. Description qty mi16150-109 30105069 washer 2 mi16150-110 30105070 p.V.C 1" 1 mi16150-111 30105071 sanding cloth 1 mi16150-112 30105072 washer 2 mi16150-113 30105073 sanding cloth 1 mi16150-114 30105074 arbor 1 mi16150-118 30105076 sanding cloth 1 mi16150-119 3...
Page 15
Parts list for 16150 part no. Ref. No. Description qty mi16150-170 s0110600 nut 1 mi16150-171 10401029 rubber feet 4 mi16150-172 s0030512 sinking head screw 4 mi16150-173 s0110500 nut 4 mi16150-175 s0050505a set screw 1 mi16150-176 30101002g-1 indicator cover 1 mi16150-177 s0720302 rivet 1 mi16150-1...