Magnum MN-101 Quick Reference Manual
Quick Reference Guide
V2.12
Relates To Firmware Version 01.07.xx
MN-101
Chrosziel GmbH, Klausnerring 6, 85551 Heimstetten, Germany, Phone +49 89 901 091 0, Fax +49 89 447 0861,
info@chrosziel.de
;
http://www.chrosziel.de
Motor Control Unit
Hand Control Unit
Light socket
Only for original scale
illumination LED light!
Battery
7.2V SONY FM-50/55
Type
Power Button (On/Off) & LED
Green = Battery Good
Flashing = Battery Low - change battery
Unit switches off automatically, when
battery power becomes too low
Area of built-in GHz Antenna
Do not cover- keep clear!
Camera Record
Start/Stop
LED flashes = Record is on
Automatic adjustment of lens-scale
limits and motor-test of connected
digital motor:
This adjustment has to be made whenever
motor and/or lens are changed.
Do not block or stop the lens while end stops
are checked, all parameters will then be
stored incorrectly!
Procedure:
• engage motor onto lens (not at an
end stop)
• Push "Motor Cal." button, red LEDs flash
• Motor starts turning slowly
The lens-scale limit will be checked and
stored automatically.
Motor Socket
Type: Lemo EGG. 1B. 307
Pin 1: Motor
–
Pin 2: Motor +
Pin 3: Encoder channel A
Pin 4: +5V
Pin 5: earth/ground
Pin 6: Encoder channel B
Pin 7: Sense
Power LED
Green = Power Good (>12V)
Red = Input voltage low
Flashing = voltage drop occurred
Power In (10V -30V; with
electronic Fuse & reverse
protection) & Cam Start/Stop
Type: Lemo 0B.305
Pin 1: Battery plus
Pin 2: CAM Relay contact 1
Pin 3: CAM Relay contact 2
Pin 4: Battery minus / GND
Hand wheel with fixed Fluid
Drag
Accepts 2 different types of scales:
Big Ring
Small Ring (as shown in photo)
Menu Navigation
Press Center button to
enter the Setup Menu
Battery Release
Slide to the right to change battery
USB Socket for Software Updates and USB Status LED
(always update both MCU and hand unit)
Software updates are provided by Chrosziel, when available .
Update Procedure:
Copy the two software files into the root of an USB stick (FAT/FAT32
formatted)
Plug USB stick into socket.
Power down the unit
Press and hold
down “Motor Cal” button and repower the receiver.
Unit will perform the update indicating the progress by different LED blinking
patterns on the front. After update the Unit restarts automatically
USB Socket for Software
Updates
(always update both MCU
and hand unit)
Software updates are provided by
Chrosziel, when available.
Update Procedure:
Copy the two provided software
files into the root of an USB stick
(FAT/FAT32 formatted)
Power down the handset
Plug USB stick into socket.
Press
and hold down “REC”
button and power on the handset.
Unit will perform the update
indicating
the
progress
by
different LED flashing patterns on
the front. After update the unit
restarts automatically
Area of Built-in GHz Antenna
Do not cover- keep clear!
Cam Start/Stop indicator
LED
blue
=
relay
switches
active/connected
off
=
relay
switches
inactive/disconnected
Radio Channel Selector + Rf Error LED
Select radio channel within the 2.4 GHz Band
(select 5 .. F). Red LED goes on if connection
error occurs. Channels 0..4 not valid! If chosen,
LED is flashing.
Cam Start/Stop
Type: Lemo ECB.0B.309
Pin 8: CAM Relay 1
Pin 9: CAM Relay 2
Rf Error LED
Rf Error LED goes on if no
connection to at least one
hand
unit
could
be
established.
Choose same channel in the
Set Up menu of the hand
unit.
Motor Status Red LEDs
Signaling
Slow blinking = motor limits
need to be calibrated
Fast
flashing
=
motor
calibration in progress
Off with motor connected =
motor limits are calibrated,
ready to shoot
4 User assignable Keys
(U1 .. U4)
Currently fixed to spread the
wheel scale
6x 1/4" Threads
for attaching of additional
accessories.
Caution:
Maximum length of screw
turned into the thread is
<= 8 mm (5/16")!
.