DL manuals
Magnum
Paint Sprayer
XR5
Operator's Quick Manual

Magnum XR5 Operator's Quick Manual

Manual is about: Airless

Page of 10

Download

Print this page

Bookmark us

9557A

9558A

9559A

AGNUM

XR9

AGNUM

XR7

AGNUM

XR5

Operator’s Quick Guide

Warnings

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Required Tools and Accessories

. . . . . . .

System Components

. . . . . . . . . . . . . . . . .

Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Priming

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing Tip & Guard

. . . . . . . . . . . . . . . .

Spraying Techniques

. . . . . . . . . . . . . . . . .

Shutdown and Cleaning

. . . . . . . . . . . . .

Preparing for Storage

. . . . . . . . . . . . . . .

Basic Troubleshooting

. . . . . . . . . . . . . .

XR Series Airless Sprayers

Contents

All written and visual data contained in this document reflect the latest

product information available at the time of publication. Graco reserves the

right to make changes at any time without notice.

GRACO INC.

P.O. BOX 1441 MINNEAPOLIS, MN

55440–1441

PRINTED IN USA 309203 Rev. C 07/2000

To find your Graco/M

AGNUM

authorized service center

See the enclosed Graco/M

AGNUM

Authorized Service Centers list

Visit our website at www.graco.com

Call us at 1–888–541–9788

NEED HELP?

Call us at

1-888-541-9788

This guide is intended as a reference. To prevent injury

and equipment damage and to maximize sprayer

performance and service life, read the enclosed

Operating Instructions before you use this sprayer.

Important Notice

1 2 3 4 5 6 7 Next › »

Summary of XR5

Page 1
9557a 9558a 9559a m agnum xr9 m agnum xr7 m agnum xr5 operator’s quick guide t warnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . Required tools and accessories 2 . . . . . . . System components 2 . . . . . . . . . . . . . . . . . Setup 3 . . . . . . . . . . . . . . . . . . . . . . . ....
Page 2
18 1. Screw inlet screen onto suction tube. System is ready for next use. Flush system (steps 1 to 9, page 4) before spraying next coating. Inlet screen 2. Coil up hose. Leave it connected to sprayer and gun. Preparing for storage stowing sprayer m agnum xr7 & xr9 have hose/cord wrap brackets on han...
Page 3
16 shutdown and cleaning 1. Place suction tube in storage fluid bottle and prime tube in waste pail. Prime storage fluid: pump armor or mineral spirits/paint thinner always pump storage fluid through system after cleaning. Water left in sprayer will corrode and ruin pump. This is the procedure for p...
Page 4
14 shutdown and cleaning 1. Clean tip & guard and inlet screen with water and a brush. Inlet screen tip & guard 2. Remove gun filter, and clean it with water and a brush. Cleaning tip & guard, inlet screen, and gun filter gun filter (xr5) gun filter (xr7/xr9) first unscrew hose then unscrew brass fi...
Page 5
12 10. Turn spray/prime valve to spray. Spray shutdown and cleaning saving paint: step 13 is for returning paint in hose back to paint pail. One 50-foot (15-meter) hose holds approximately 1 quart (1 liter) of paint. Power flushing after spraying water-base paint open fluid splashback hazard (see wa...
Page 6
10 1. Turn power switch off. Shutdown and cleaning for short shutdown periods (breaks on the job), leave suction tube and prime tube in paint, and relieve the pressure by turning the spray/prime valve to prime (see warnings sheet). For extended shutdown periods, clean sprayer by flushing as instruct...
Page 7
8 spraying techniques sprayer is set up for most airless spraying applications. For details on tip selection, tip wear, coat thickness, and so on, see spraying techniques in enclosed operating instructions. Motor runs only when gun is triggered. Sprayer is designed to stop pumping when gun trigger i...
Page 8
6 installing tip & guard 2. Make sure tip & guard parts are assembled in order shown below. Metal seat black rubber gasket (for water-base paint) retaining nut put metal seat and black rubber gasket on pencil point, and insert them into guard together. Tip & guard are pre-assembled with black gasket...
Page 9
Priming waste prime 1. Turn spray/prime valve to prime. Flushing out factory or storage fluid and loading pump with water 7. Plug sprayer into grounded outlet, and turn power switch on. 5. Screw power flush attachment (included with sprayer) onto garden hose, and open power flush attachment. Prime t...
Page 10
Pressure control knob 2 warning instructions in this guide are for water-base coatings. Read fire and explosion hazard on enclosed warnings sheet. To prevent injury and equipment damage and to maximize sprayer performance, read all warnings, cautions, and procedures in enclosed operating instruction...