- DL manuals
- Magtek
- Card Reader
- 99875320-5
- Technical Reference Manual
Magtek 99875320-5 Technical Reference Manual
Summary of 99875320-5
Page 1
Usb hid intellihead for swipe readers technical reference manual manual part number 99875320-5 october 2008 registered to iso 9001:2000 phone: (562) 546-6400 technical support: (651) 415-6800 www.Magtek.Com 1710 apollo court seal beach, ca 90740 fax: (562) 546-6301.
Page 2
Ii.
Page 3
Iii c printed in the united states of america lectronic or mechanical, for any purpose, ithout the express written permission of magtek, inc. Agtek is a registered trademark of magtek, inc. Tellihead ™ is a trademark of magtek, inc. 998 by compaq computer corporation, intel corporation, microsoft co...
Page 4
Iv te horized by magtek to resell the products, in which event, this warranty ll, at its laced e, ek reserves the right to examine the . T, a three (3) day shipping service. A return material authorization (rma) number must accompany y ding any warranty of merchantability or o dvised of the possibil...
Page 5
V fcc warning statement n the ul mmunications. However, there is no guarantee that interference will not occur in a articular installation. Fcc compliance statement 2) this device must accept any interference ceived, including interference that may cause undesired operation. Canadian doc statement d...
Page 6
Table of contents section 1. Features and specifications..................................................................................... 1 1 2 2 2 5 5 5 5 7 7 9 9 10 11 11 12 12 12 12 12 13 13 13 13 13 14 14 14 14 15 15 16 17 18 19 20 21 22 23 25 25 25 26 27 features...............................
Page 7
Tables and figures figure 1-1. Usb intellihead 3-track .......................................................................................................... V iii 5 28 29 30 31 32 33 34 35 36 table 1-1. Specifications.................................................................................
Page 8
Viii figure 1-1. Usb intellihead 3-track.
Page 9
Section 1. Features and specifications the usb (universal serial bus) hid (human interface device) intellihead swipe reader is a compact magnetic stripe card reader that conforms to iso standards. The reader is compatible with any device with a usb host interface. A card is read by sliding it past t...
Page 10
Usb hid intellihead swipe reader hardware configurations the hardware configurations are as shown in the table below. Drawings of each model are included in appendix a. Part number description cable length and connector type rail or housing 21030006 usb hid intellihead on spring 125mm, 5 pin molex n...
Page 11
Section 1. Features and specifications specifications table 1-1 lists the specifications for the usb intellihead. Table 1-1. Specifications reference standards iso 7810, iso 7811, aamva and jis x 6302* power input 5v from usb bus recording method two-frequency coherent phase (f2f) message format asc...
Page 12
Usb hid intellihead swipe reader 4.
Page 13: Section 2. Installation
5 section 2. Installation this section describes the cable connection, the windows plug and play setup, and the physical mounting of the unit. Usb connection since the usb intellihead is supplied as an oem product, the installation and system integration will be unique for each application. The read...
Page 14
Usb hid intellihead swipe reader 6.
Page 15: Section 3. Operation
7 section 3. Operation card read a card may be swiped past the read head at any time. The magnetic stripe must face toward the head and may be swiped in either direction. If there is data encoded on the card, the device will attempt to decode the data and then send the results to the host via a usb ...
Page 16
Usb hid intellihead swipe reader 8.
Page 17
Section 4. Usb communications this device conforms to the usb specification revision 1.1. This device also conforms with the human interface device (hid) class specification version 1.1. The device communicates to the host as a vendor-defined hid device. The details about how the card data and comma...
Page 18
Usb hid intellihead swipe reader have a usage page in the range 0xff00 – 0xffff. All usages for this device use vendor-defined magnetic stripe reader usage page 0xff00. The usage ids for this device are defined in the following table. The usage types are also listed. These usage types are defined in...
Page 19
Section 4. Usb communications item value (hex) input (data, variable, absolute, buffered bytes) 82 02 01 usage (track 3 data) 09 32 report count (110) 95 6e input (data, variable, absolute, buffered bytes) 82 02 01 usage (command message) 09 20 report count (24) 95 18 feature (data, variable, absolu...
Page 20
Usb hid intellihead swipe reader track 2 decode status bits 7-1 0 value reserved error this is a one-byte value, which indicates the status of decoding track 2. Bit position zero indicates if there was an error decoding track 2 if this bit is set to one. If it is zero, then no error occurred. If a t...
Page 21
Section 4. Usb communications card encode type this one-byte value indicates the type of encoding that was found on the card. The following table defines the possible values. Value encode type description 0 iso/aba iso/aba encode format 1 aamva aamva encode format 2 cadl cadl encode format. Note tha...
Page 22
Usb hid intellihead swipe reader commands most host applications do not need to send commands to the device. Most host applications only need to obtain card data from the device as described previously in this section. This section of the manual can be ignored by anyone who does not need to send com...
Page 23
Section 4. Usb communications data. The hid specification requires that reports be fixed in length. Command data may vary in length. Therefore, the report should be filled with zeros after the valid data. Result code this one-byte field contains the value of the result code. There are two types of r...
Page 24
Usb hid intellihead swipe reader the result codes for the get and set property commands can be any of the codes list in the generic result code table. Property id is a one-byte field that contains a value that identifies the property. The following table lists all the current property id values: val...
Page 25
Section 4. Usb communications serial_num property property id: 0x01 property type: string length: 0 – 15 bytes get property: yes set property: yes default value: the default value is no string with a length of zero. Description: the value is an ascii string that represents the device’s serial number...
Page 26
Usb hid intellihead swipe reader polling_interval property property id: 0x02 property type: byte length: 1 byte get property: yes set property: yes default value: 10 description: the value is a byte that represents the devices polling interval for the interrupt in endpoint. The value can be set in t...
Page 27
Section 4. Usb communications max_packet_size property property id: 0x03 property type: byte length: 1 byte get property: yes set property: yes default value: 8 description: the value is a byte that represents the devices maximum packet size for the interrupt in endpoint. The value can be set in the...
Page 28
Usb hid intellihead swipe reader track_id_enable property property id: 0x04 property type: byte length: 1 byte get property: yes set property: yes default value: 0x95 description: this property is defined as follows: id 0 t 3 t 3 t 2 t 2 t 1 t 1 id 0 – decodes standard iso/aba cards only 1 – decodes...
Page 29
Section 4. Usb communications interface_type property property id: 0x10 property type: byte length: 1 byte get property: yes set property: yes default value: 0 (hid) description: the value is a byte that represents the devices interface type. The value can be set to 0 for the hid interface or to 1 f...
Page 30
Usb hid intellihead swipe reader decode_enable property property id: 0x1a property type: byte length: 1 byte get property: yes set property: yes default value: 0x00 description: this property is defined as follows: bit position 7 6 5 4 3 2 1 0 decode type reserved reserved reserved reserved reserved...
Page 31
Section 4. Usb communications reset_device command command number: 0x02 description: this command is used to reset the device. This command can be used to make previously changed properties take affect without having to unplug and then plug in the device. When the device resets, it automatically doe...
Page 32
Usb hid intellihead swipe reader 24.
Page 33: Section 5. Demo Program
Section 5. Demo program the demo program, which is written in visual basic, can be used to do the following: • read cards from the device and view the card data • send command requests to the device and view the command responses • guide application developers in their application development by pro...
Page 34
Usb hid intellihead swipe reader 26 source code source code is included with the demo program. It can be used as a guide for application development. It is described in detail, with comments, to assist developers. The book usb complete by jan axelson is also a good guide for application developers, ...
Page 35: Appendix A. Drawings
Appendix a. Drawings the following drawings are provided in this section: part number title 21030006 usb hid intellihead, 3-track, 125mm wire, 5-pin molex connector 21030010 usb hid intellihead, 3 track, 440mm wire, 5-pin molex (reverse pin out) 21030042 usb hid intellihead, 3 track, 4.05mm beam arm...
Page 36
Usb hid intellihead swipe reader figure a-1. Usb hid intellihead, 3-track, 125mm wire, 5-pin connector 28.
Page 37
Appendix a. Drawings figure a-2. Usb hid intellihead, 3-track, 440mm wire, 5-pin reverse connector 29.
Page 38
Usb hid intellihead swipe reader figure a-3. Usb hid intellihead, 3-track, 125mm wire, 4.05mm beam arm, 5-pin molex 30
Page 39
Appendix a. Drawings figure a-4. Usb hid intellihead, 3-track, 6’ cable, usb-a connector, 100mm black 31.
Page 40
Usb hid intellihead swipe reader figure a-5. Usb hid intellihead, 3-track, 6” cable, usb-a connector, 100mm black 32.
Page 41
Appendix a. Drawings figure a-6. Usb hid intellihead, 3-track, 125mm wire, 5-pin molex connector, 43mm rail 33.
Page 42
Usb hid intellihead swipe reader figure a-7. Usb hid intellihead, 3-track, 125mm wire, 5-pin connector, 90mm rail 34.
Page 43
Appendix a. Drawings figure a-8. Usb hid intellihead, 3-track, 125mm wire, 5-pin molex connector, 60mm slim profile 35.
Page 44
Usb hid intellihead swipe reader 36 figure a-9. Usb hid intellihead, 3-track, 125mm wire, 5-pin molex connector, 90mm slim profile.