- DL manuals
- Magtek
- Media Converter
- INTELLISTRIPE 380
- Technical Reference Manual
Magtek INTELLISTRIPE 380 Technical Reference Manual
Summary of INTELLISTRIPE 380
Page 1
Intellistripe 380 usb/rs-232 desktop motorized reader-encoder technical reference manual manual part number 99875275-3 august 2007 registered to iso 9001:2000 1710 apollo court seal beach, ca 90740 phone: (562) 546-6400 fax: (562) 546-6301 technical support: (651) 415-6800 www.Magtek.Com.
Page 2
Ii copyright © 2001-2007 magtek ® , inc. Printed in the united states of america information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express wri...
Page 3
Iii registered to iso 9001:2000 magtek part number 99875275-1 1710 apollo court, seal beach, ca 90740 25 february 2003 voice: 562-546-6400 fax: 562-546-6301 software license agreement important: you should carefully read all the terms, conditions and restrictions of this license agreement before ins...
Page 4
Iv fcc warning statement this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environme...
Page 5
V 1 1 1 2 2 2 2 2 4 4 4 4 5 5 5 6 6 6 6 6 6 7 7 7 7 7 8 8 8 8 8 8 8 8 9 9 9 9 9 9 10 11 11 11 11 11 table of contents section 1. Features and specifications..................................................................................... Configurations ..............................................
Page 6
Vi 11 11 12 19 19 19 19 19 21 21 21 21 21 21 flange................................................................................................................................................. Magtek mounting plate.....................................................................................
Page 7
Vii viii 10 12 12 13 14 14 15 15 16 16 17 19 20 20 22 23 24 25 10 14 15 16 table of figures figure 1-1. Intellistripe 380--------------------------------------------------------------------------------------------------- table 1.1. Specifications -----------------------------------------------------...
Page 8
Viii figure 1-1. Intellistripe 380
Page 9
1 section 1. Features and specifications the intellistripe ® 380, desktop motorized reader-encoder reads and encodes magnetic-stripe cards and smartcards. Configurations part numbers and descriptions for the basic configuration are as follows: 16050408 intellistripe 380 16050410 intellistripe 380, m...
Page 10
Intellistripe 380 2 applicable documents standards iso 7811-2, -3, -4, -5 identification cards tracks 1-3 iso 7810 physical specifications iso 7816 smartcard specifications emv 1996 europay-mastercard-visa 1996 level i specification emv 2000 europay-mastercard-visa 2000 level i specification magtek ...
Page 11
Section 1. Features and specifications 3 motorized card transport the card transport is based on an existing magtek magstripe/encode module. This module incorporates the following features: lead-in roller system the primary purpose of the lead-in roller system is to grab the card from the user durin...
Page 12
Intellistripe 380 4 spring-loaded card registration guide(s) the spring-loaded guide ensures that the reference edge of the card is mechanically referenced to the magnetic read/write head, so that the magnetically encoded track data is physically located on the magstripe in accordance with the speci...
Page 13
Section 1. Features and specifications 5 direction of magnetic read: the iso 7810 and 7811 specifications allow for bidirectional magnetic reading of the card. As such, the reader provides services that allow the card to be read in either direction. Read formats: in addition to reading cards that me...
Page 14
Intellistripe 380 6 cable management the following provisions are made for communication and power lines: • polarization and locking of cable connectors • strain relief of cables • wire routing functionality • rj series connectors for main and auxiliary rs-232 interfaces. • power is brought to the u...
Page 15
Section 1. Features and specifications 7 ram space: 40 k bytes rom space: rom flash: main program memory: 512 k bytes boot loader memory: 24 k bytes configuration memory: 8 k bytes host serial port the rs-232 host serial port provides serial communications between the reader/encoder and the host com...
Page 16
Intellistripe 380 8 opto-sensor inputs the main pcb provides inputs for the three opto-sensors (front, encode, and rear). Rotary pulse generator the main pcb provides input for the magtek 75/210 bpi rotary pulse generator (rpg). External sam ranch interface, optional the main pcb provides resources ...
Page 17
Section 1. Features and specifications 9 external auto-ranging power pack the reader/encoder is powered from an external power-pack, which is located near the host computer system. Power is routed to the reader/encoder through the host rs-232 cable. Auto-ranging input the external power pack feature...
Page 18
Intellistripe 380 10 specifications the specifications are listed in table 1-1. Table 1.1. Specifications operating msr read-data format specifications supported mag-stripe: ansi/iso 7810, 7811/aamva/ for tracks 1, 2, and 3 smart card: iso 7816-1, -2, and -3 encode coercivity ranges loco = 325 oe +/...
Page 19: Section 2. Installation
11 section 2. Installation the installation of the intellistripe 380 reader-encoder consists of mounting the unit on a flat surface, connecting the i/o rs-232 cable to the host serial port, the auxiliary cable to a peripheral device, and the power supply to the i/o cable and to a wall receptacle. Mo...
Page 20
Intellistripe 380 12 foot pads (4) mounting screws #4-40 (3) 5.789 3.230 1.616 1.105 .546 figure 2-1. Dimensions for mounting holes for 3-screw set and foot pads lock-in-place slots (4) Ø .125 mounting flange (1) (use with lock-in-place mounting holes) 4.330 .375 (4) .959 .180 (4) 2.810 2.032 1.147 ...
Page 21
Section 2. Installation 13 . Card ejector rod mounting flange card ejector rod rear panel guide slots & attachment holes figure 2-3. Rear panel and cover connect the host pc cable (p/n 16051417) to the rs-232 connector on the intellistripe 380 as shown in figure 2-4 for the rs-232 connection. Connec...
Page 22
Intellistripe 380 14 cable p/n 16051417 to pc power supply (with cable) p/n 64300091 north american 110v power cord p/n 71100001 figure 2-4. Cable connections - rs-232 table 2-1 lists the pins for the host cable p/n 16051417. Table 2-1. Pin list for intellistripe 380 to host pc cable p/n 16051417 10...
Page 23
Section 2. Installation 15 cable connections for the usb are shown in figure 2-5, and the pin lists are shown in table 2-2 and table 2-3. Intellistripe 380 back panel p1 p4 p2 p3 pin 4 pin 1 pin 1 pin 5 pin 1 pin 10 power supply (with cable) p/n 64300091 cable p/n 16051422 north american 110v power ...
Page 24
Intellistripe 380 16 table 2-3. Cable connections – usb power p3 – 2.5 mm power jack wire color p4 – 10p10c rj plug shell gnd drain wire 1 pwr gnd center pin +12 26awg wire (black) 2 +12 shell gnd braid shield 6 pwr gnd center pin +12 26awg wire (brown) 8 +12 center pin +12 26awg wire (red) 10 +12 c...
Page 25
Section 2. Installation 17 ejector rod hole for card removal power and usb cable p/n 16051422 rear panel cover figure 2-7. Rear panel cover replaced – usb connection plug in the power supply into a wall receptacle..
Page 26
Intellistripe 380 18.
Page 27
Section 3. Operation and maintenance the operation of the unit includes inserting and removing the card. Maintenance includes keeping the unit clean and removing jammed cards from the unit. Operation the card is inserted with the magnetic stripe down and to the right as illustrated in figure 3-1. Pe...
Page 28
Intellistripe 380 shut power off by unplugging the power supply (figure 2-4), and remove the card with the rod as follows: 1. Remove the rear panel cover to access the ejector rod as indicated in figure 3-2. Rear panel cover ejector rod hole for card removal rear panel card ejector rod figure 3-2. E...
Page 29
21 appendix a. Dimensions for mounting mounting the bottom of the unit is shown in figure 2-1 and 2-2. The intellistripe 380 may be mounted in one of three ways: 1) foot pads, 2) set of mounting holes for 3 screws (4 x 40), and 3) 4 lock-in- place slots. The mounting dimensions of the 3 screw holes ...
Page 30
Intellistripe 380 figure a-1. Mounting dimensions 1 22.
Page 31
Appendix a. Dimensions for mounting 23 figure a-2. Mounting dimensions 2.
Page 32
Intellistripe 380 24 figure a-3. Magtek mounting plate, i380, 1.
Page 33
Appendix a. Dimensions for mounting 25 figure a-4. Magtek mounting plate, i380, 2.
Page 34
Appendix a. Dimensions for mounting 26.