Magtrol DSP6000 User Manual - 1 - Introduction
1
ABOUT THIS MANUAL
This manual contains information about the DSP6000
Dynamometer Controller and procedures for optimal
use. To obtain the best results from your unit, please
follow the procedures for operation.
SHIPPING
Your DSP6000 was packaged carefully for shipping.
Please notify your carrier and Magtrol Customer Service
if you believe your unit was damaged in shipping.
U
NPACKING
Y
OUR
DSP6000
1. Save all shipping cartons and packaging material
until you inspect the DSP6000.
2. Inspect the DSP6000 for any evidence of damage
in shipping.
3. Make sure the carton contains the following:
•
DSP6000 Dynamometer Controller
•
Line cord
•
User's Manual for the DSP6000
•
Calibration certificate
ABOUT THE MODEL DSP6000
DYNAMOMETER CONTROLLER
Magtrol's Model DSP6000 Dynamometer Controller
provides superior motor testing capabilities by using
state-of-the-art digital signal processing technology.
The DSP6000 both controls the dynamometer and
provides digital readouts on the front panel. The
DSP6000 is designed to work with all Magtrol load cell
dynamometers, including the following dynamometer
models:
0
0
1
-
D
H
0
1
5
-
D
H
0
0
8
-
D
H
5
1
7
-
D
E
6
0
1
-
D
H
0
0
7
-
D
H
5
0
8
-
D
H
5
1
8
-
D
E
0
0
4
-
D
H
5
0
7
-
D
H
0
1
8
-
D
H
0
0
1
-
D
T
H
0
0
5
-
D
H
0
1
7
-
D
H
5
1
8
-
D
H
0
0
2
-
D
T
H
5
0
5
-
D
H
5
1
7
-
D
H
5
2
8
-
D
H
0
0
3
-
D
T
H
F
EATURES
Fast, full curve data acquisition
Free-run to locked rotor in seconds.
1 - Introduction
1 - Introduction
1 - Introduction
1 - Introduction
1 - Introduction
High-speed data acquisition
120 torque and speed points per second via IEEE
(GPIB) bus.
Speed and torque operating modes
Each mode provides independent PID settings for
improved dynamometer control.
Programmable digital PID values
Controlled and stored either with Magtrol M-Test
software or manually.
Single point or programmed load control
Single or multi-point torque and speed stabilized testing
using Magtrol M-Test software.
Two standard computer interfaces
RS-232 and IEEE-488.
Additional analog input
Accepts any ± 5 VDC transducer.
Vacuum fluorescent display
Displays torque, speed, power, auxiliary input and PID
values.
Many torque measurement options
Includes English, metric, and SI torque readings as
standard.
Closed box calibration of torque and auxiliary input
Eliminates need to open box for adjustments.
The DSP6000 is designed to work with any personal
computer using an IEEE-488 or an RS-232 interface,
or as a stand-alone unit. In a computer-controlled
environment, the DSP6000 provides the following
motor testing capabilities:
•
Proportional (P), plus Integral (I), plus
Derivative (D) closed loop control (PID loop).
•
Torque (Q) and Speed (N) data acquisition at a
rate of up to 120 readings per second.
•
Automatic progressive loading in either
decreasing or increasing speed mode.
•
Ability to remove the Effects of Inertia from
dynamically obtained data. (See Appendix B)
•
Complete curve capability for most motor
types, including single/poly phase induction,
AC/DC series, PMDC, brushless DC, air and
internal combustion (if suitably coupled).