1. DL manuals
  2. Majestic
  3. Indoor Fireplace
  4. 33BDVR
  5. Installation Instructions And Homeowner's Manual

Majestic 33BDVR Installation Instructions And Homeowner's Manual

Summary of 33BDVR

  • Page 1

    Installation instructions and homeowner's manual 10003357 12/04 rev. 8 installer: do not discard this manual - leave for homeowner builder rear vent direct vent models: 33bdvr, 36bdvr 39bdvr, 43bdvr do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any oth...

  • Page 2: Table of Contents

    2 bdvr series direct vent gas fireplace 10003357 please read the installation & operating instructions before using appliance. Thank you and congratulations on your purchase of a cfm specialty home products fireplace. Important: read all instructions and warnings carefully before starting installati...

  • Page 3

    3 bdvr series direct vent gas fireplace 10003357 this gas appliance should be installed by a qualified installer in accordance with local building codes and with current csa-b149.1 installation codes for gas burning appliances and equipment. For usa installations follow local codes and/or the curren...

  • Page 4: Fireplace Dimensions

    4 bdvr series direct vent gas fireplace 10003357 ref. 33bdvr 36bdvr 39bdvr 43bdvr a 33” (838mm) 36” (914mm) 39” (991mm) 43” (1092mm) b 28 ⁷⁄₈ ” (733mm) 34 ¹⁄₄ ” (870mm) 34 ¹⁄₄ ” (870mm) 37” (940mm) c 31” (787mm) 33” (838mm) 36” (914mm) 40” (1016mm) d 16 ³⁄₈ ” (416mm) 21” (533mm) 21” (533mm) 23 ¹⁄₂ ”...

  • Page 5

    5 bdvr series direct vent gas fireplace 10003357 top of unit to ceiling ............................. 36” (914mm) appliance top ....................................................... 0” (0 mm) bottom ................................................. 0” (0 mm) side .....................................

  • Page 6

    6 bdvr series direct vent gas fireplace 10003357 noncombustible materials such as brick or tile may be extended over the edges of the face of the fireplace. Do not cover any vent or grille panels. If a trim kit is going to be installed on the fireplace, the brick or tile will have to be installed fl...

  • Page 7

    7 bdvr series direct vent gas fireplace 10003357 installation 1. Thread the wiring through the holes on the end panels of the fireplace. Take care not to cut the wire or insulation on metal edges. Route the wire to a conveniently located receptacle box. 2. Attach the wire to the on/off switch and in...

  • Page 8

    8 bdvr series direct vent gas fireplace 10003357 the fireplace, when installed, must be electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current csa c22.1 canadian electrical code. For usa installations follow local codes and the national...

  • Page 9: General Venting

    9 bdvr series direct vent gas fireplace 10003357 your fireplace is approved to be vented either through the side wall, or vertically through the roof. • only venting components specifically approved and labelled for this fireplace may be used. • vent terminations shall not be recessed into a wall or...

  • Page 10

    10 bdvr series direct vent gas fireplace 10003357 v v v v v v v x x x d e b b b c b m b a j k f l vent termination air supply inlet area where terminal is not permitted h i fixed closed fixed closed operable operable fixed closed v b inside corner detail v a g v n n v v g g a cfm145a general venting...

  • Page 11

    11 bdvr series direct vent gas fireplace 10003357 general information assembling vent pipes canadian installations: venting system must be installed in accordance with the current csa-b149.1 installation code. Usa installations: the venting system must conform with local codes and/ or the current na...

  • Page 12

    12 bdvr series direct vent gas fireplace 10003357 the vent chart should be read in conjunction with the following vent installation instructions to determine the relationship of the vertical and horizontal dimensions of the vent system. 1. Determine the height of the center of the horizontal vent pi...

  • Page 13

    13 bdvr series direct vent gas fireplace 10003357 rear wall installations step 1 locate vent opening on the wall. To locate hole center consult with appropriate fireplace dimensions, page 4. Frame as shown below. Combustible walls (fig. 14): cut a 10 ³⁄₈ ”h x 9 ³⁄₈ ” w (264 x 240mm) hole through the...

  • Page 14

    14 bdvr series direct vent gas fireplace 10003357 vertical sidewall applications finished wall vent termination fp1005 fig. 17 side view of final unit location. Since it is very important that the venting system maintain its balance between the combustion air intake and the flue gas exhaust, certain...

  • Page 15

    15 bdvr series direct vent gas fireplace 10003357 1 2 3 4 1 + 2 + 3 + 4 = 270 o cfm132 fig. 21 maximum number of elbows. • the maximum number of 45 ° elbows permitted per side wall installation is two (2). These elbows can be installed in either the vertical or horizontal run. • for each 45 ° elbow ...

  • Page 16

    16 bdvr series direct vent gas fireplace 10003357 step 2 measure wall thickness and cut adjustable zero clear- ance sleeve parts to proper length (maximum 12”/ 305mm). (fig. 23) adjust sleeve to minimum (9 ³⁄₈ ” x 9 ³⁄₈ ” and attach to firestop with #8 sheet metal screws (supplied). Assemble sleeve ...

  • Page 17

    17 bdvr series direct vent gas fireplace 10003357 step 6 apply high temperature sealant to 4” (102mm) and 7” (178mm) collars or the termination one inch away from the end. Guide the vent termination’s 4” and 7” collars into their respective vent pipes. Double check that the vent pipes overlap the co...

  • Page 18

    18 bdvr series direct vent gas fireplace 10003357 vertical through-the-roof installation 1. Locate your fireplace. 2. Plumb to center of the (4”) flue collar from ceiling above and mark position. 3. Cut opening equal to 9 ³⁄₈ ” x 9 ³⁄₈ ” (240 x 240mm). 4. Proceed to plumb for additional openings thr...

  • Page 19

    19 bdvr series direct vent gas fireplace 10003357 if there is room above ceiling level, firestop spacer must be installed on both the bottom and the top side of the ceiling joists. If an attic is above ceiling level a 7dvais (attic insulation shield) must be installed. (fig. 32) the enlarged ends of...

  • Page 20

    20 bdvr series direct vent gas fireplace 10003357 twist lock venting components 7tdvrvt - through the wall rear vent termination starter kit-model 7tdvsk-sidewall venting starter kit-model 7tdvskv-vertical venting for 7tdvskv-a order 1/12 to 6/12 roof pitch for 7tdvskv-b order 7/12 to 12/12 roof pit...

  • Page 21: Operating Instructions

    21 bdvr series direct vent gas fireplace 10003357 only glass approved by cfm specialty home products should be used on this fireplace. The top louvre panel is removed by lifting the panel vertically and pulling it away from the appliance. (fig. 36) the lower access door is hinged along the bottom ed...

  • Page 22

    22 bdvr series direct vent gas fireplace 10003357 unpack the logs from packaging and remove each log from its wrapping materials. The logs are fragile and should be handled with care. Keep the packaging material out of the reach of children and dispose of the material in a safe manner. The individua...

  • Page 23

    23 bdvr series direct vent gas fireplace 10003357 43bdvr refer to figure 41 1. Remove the top louvre assembly. 2. Remove the window frame assembly. 3. Fit the rear left log (bd11) onto the rear log support. Ensure the back of the log is flat against the rear wall of the support. 4. Fit the front lef...

  • Page 24

    24 bdvr series direct vent gas fireplace 10003357 rn/rp & en/ep models for units equipped with “hi/lo” valves the flame adjustment is accomplished by rotating the “hi/lo” adjustment knob located near the center of the gas control valve. (figs. 42 & 43) it is important to periodically perform a visua...

  • Page 25

    25 bdvr series direct vent gas fireplace 10003357 3. Open control access panel. 4. Push in gas control knob slightly and turn clockwise to "off". Do not force. 5. Close control access panel. 1. Stop! Read the safety information above. 2. Turn off all electrical power to the fireplace. 3. For mn/mp/t...

  • Page 26

    26 bdvr series direct vent gas fireplace 10003357 lighting and operating instructions for fireplaces equipped with sit822 gas valve (en or ep) a. This fireplace is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. B. Before operating, smell...

  • Page 27

    27 bdvr series direct vent gas fireplace 10003357 troubleshooting - honeywell millivolt valve remove window frame assembly before service work start check gas supply on ▼ ▼ ▼ ▼ ▼ pilot lights with piezo ignitor • lockout has engaged. Wait 60 seconds and try again. • for spark at electrode while depr...

  • Page 28

    28 bdvr series direct vent gas fireplace 10003357 warning: before doing any gas control service work, remove glass front. Symptom possible causes corrective action 1. Spark ignitor will not light a. Defective or misaligned using a match, light pilot. If pilot lights, turn off electrode at pilot. Pil...

  • Page 29

    29 bdvr series direct vent gas fireplace 10003357 sit 822 valve with a honeywell electronic ignitor troubleshooting the gas control system start •turn gas supply off • turn on/off switch to call for heat "on" power to module (24v normal) spark across ignitor sensor gap yes yes yes • turn gas on pilo...

  • Page 30

    30 bdvr series direct vent gas fireplace 10003357 the conversion of this appliance from one gas to another must be carried out by an authorized service provider. 1. Disconnect power to the unit and shut off the gas supply. 2. Remove window frame assembly. 3. Carefully remove the logs & lava rock mat...

  • Page 31: Maintenance

    31 bdvr series direct vent gas fireplace 10003357 maintenance burner and burner compartment it is important to keep the burner and the burner compartment clean. At least once per year the logs and lava rock/ember material should be removed and the burner compartment vacuumed and wiped out. Remove an...

  • Page 32: 33/36/39/43Bdvr

    32 bdvr series direct vent gas fireplace 10003357 l ohi pilot adj pilot on off hi lo 2a/b 18 17 13a/b 14a/b 12a/b 16 11 20 24 15 8 7 5 3a/b 4a/b 19 21 22 23 6 10 25 9 26 1f 1h 1b 33bdvr 1c 1a 1b 36bdvr 1f 1a 1e 1g 39bdvr cfm specialty home products reserves the right to make changes in design, mater...

  • Page 33: Bdvr

    33 bdvr series direct vent gas fireplace 10003357 bdvr (continued) (items marked “*” are not shown) ref. Description 33bdvr 36bdvr 39bdvr 43bdvr 1. Log set (complete) 10003685 10003353 100003354 10003696 1a. Log - front left --- bb11 bc11 bd12 1b. Log - front right ba9 bb12 --- bd14 1c. Log - rear -...

  • Page 34: Bdvr

    34 bdvr series direct vent gas fireplace 10003357 bdvr (continued) (items marked “*” are not shown) ref.Description 33bdvr 36bdvr 39bdvr 43bdvr * fan speed control, (fk24 option) 51738 51738 51738 51738 * knob, fan speed control, (fk24 option) 51882 51882 51882 51882 18. Fan assembly, with bracket (...

  • Page 35

    35 bdvr series direct vent gas fireplace 10003357 fk24 fan assembly this auxiliary fan system increases the efficiency of the circulation of the heated air. The fk24 fan kit allows variable speed control of the circulation fan and also incorporates a heat sensor in the circuit. Specifications 115 vo...

  • Page 36

    36 bdvr series direct vent gas fireplace 10003357 ceramic refractory panels are available in kit form for the bdv series appliances appliance model kit name 33bdvt at1tbt 33bdvr at1cbb 36bdvt bt2cbb 39bdvt ct2cbb 43bdvt dt2cbb 6. Place the rear refractory panel in place. Locate the lower edge of the...

  • Page 37

    37 bdvr series direct vent gas fireplace 10003357 either remove the top and bottom brass window trims or take care not to scratch them during the installation of the screen kit. 1. Slide the tabs on the top edge of the window screen assembly up into the slots in the underside of the top rail of the ...

  • Page 38

    38 bdvr series direct vent gas fireplace 10003357 basic warranty cfm specialty home products (hereinafter referred to collectively as the company) warrants that your new vermont castings or majestic gas fireplace/stove is free from manufacturing and material defects for a period of one year from the...

  • Page 39

    39 bdvr series direct vent gas fireplace 10003357.

  • Page 40

    Efficiency ratings model energuide ratings steady state (%) d.O.E. Fireplace efficiency (%) fan-off fan-on (afue%) 33bdvrrn 48.4 78 79 57 33bdvrrp 48.4 79 80 57 33bdvren 48.4 78 79 57 33bdvrep 48.4 79 80 57 36bdvrrn 48.9 76 79 58 36bdvrrp 48.9 77 80 58 36bdvren 48.9 76 79 58 36bdvrep 48.9 77 80 58 3...