Summary of MP-300
Page 1
Instruction manual powerpoint power supply, model mp-300
Page 2: Table Of Contents
2 table of contents packing list 3 warning 4 safety information 5 product specifications 7 product description 8 controls and features installation instructions 10 11 operation instructions 11 troubleshooting guide 13 warranty 16.
Page 3: Packing List
3 packing list mp-250 or cs-300: - 1 x mp-300 - 1 x power cord for power supply - 1 x extra fuse inside power plug on the rear of unit - 1 x power supply instruction manual.
Page 4: Warning
4 warning this power supply series has been tested and found to comply with the limits for the ce regulation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This power supply series generates, uses, ...
Page 5: Safety Information
5 safety information use high level precautions against any electrical device. Before connecting with the electrical supply, check the supply voltage is within the range stated at the rating label, and this device must be earthed. Place the unit in a safe and dry location not touching any surroundin...
Page 6
6 avoiding damage to the instrument 1. Do not attempt to operate the device if damaged. 2. Protect this unit from physical damage, corrosive agents and extreme temperatures (direct sunlight etc). 3. For proper ventilation, leave at least 10 cm of space behind the instrument, and at least 5 cm of spa...
Page 7: Product Specifications
7 product specifications output voltage / inc 2-300v / 1v output current / inc 1-700ma / 1ma max. Watt 150w operating constants voltage or current control microprocessor controller terminator pairs 4 pairs timer 1~999 mins with alarm, continuous safety device no load detect leakage detect overload d...
Page 8: Product Descriptions
8 product descriptions mp-300 power supplies are microprocessor-controlled power supplies designed to meet most electrophoresis needs in a personal, single, easy to use unit. This manual describes the setup and operation of the 300v power supply including important information on safety and maintena...
Page 9: Introduction
9 mp-250 power supply and mp-300 power supply both provide constant voltage or constant current to instruments used in electrophoresis. Features of mp-300 power supply: - compact size - advanced capacity : 150w, 700ma, 300v - microprocessor controller - constant voltages and constant currents - four...
Page 10: Controls And Features
10 controls and features front control panel 1. Key -- to increase either voltage or current or time value 2. Key - to decrease either voltage or time value 3. Key – to activate or stop the unit 4. Key – to temporarily interrupt power to an operation in progress without terminating electrophoresis a...
Page 11: Installation Instructions
11 installation instructions place on a sturdy and level surface in a safe, dry place, and connect with a buffer filled electrophoresis system. Operation instructions 1. Place the power supply on a sturdy and level surface in a safe, dry place, away from laboratory traffic. 2. Ensure that the ac pow...
Page 12
12 7. Press key, and then press key or key to adjust timer (minute) upon your request if setting time is required. It will auto stop when the timer is up. 8. Press key to start the run. The led is lit. 9. Press key to temporarily interrupt the run if necessary. The led is lit. 10. Press key again to...
Page 13: Troubleshooting Guide
13 troubleshooting guide many operating problems may be solved by carefully reading and following the instructions in this manual. Some suggestions for troubleshooting are given below. Should these suggestions not resolve the problem, contact the service department or a distributor in your region fo...
Page 14
14 high voltage application is set to run on a very low current disable no load alarm on the display screen error messages err1 ; power supply stops; alarm sounds. Current exceeds setting - check that the correct running buffer and buffer concentration have been used - check that cables are connecte...
Page 15: Maintenance
15 err3 ; power supply stops; alarm sounds groundleak detection - check electrophoresis system for earth leakage. - switch power on / off and restart application err6 ; power supply stops; alarm sounds power supply is overheating - turn off power supply immediately and check that there is adequate c...
Page 16
16 warranty these power supply units have a warranty against manufacturing and material faults of twelve months from date of customer receipt. If any defects occur during this warranty period, your dealer will repair or replace the defective parts free of charge. This warranty does not cover defects...