1. DL manuals
  2. Makita
  3. Saw
  4. 5090D
  5. Instruction Manual

Makita 5090D Instruction Manual

Other manuals for 5090D: Parts List, Parts Breakdown, Instruction Manual
Manual is about: 85 mm (3-3/8”)

Summary of 5090D

  • Page 1

    I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. W w w . M a k i t a t o o l s . C o m cordless circular saw 85 mm (3-3/8”) model 5090d.

  • Page 2: Specifications

    2 specifications • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. General safety rules usa003-1 (for all battery operated tools) warning: read and understand all instructions. Failure to follow all instructions listed bel...

  • Page 3

    3 3. Keep bystanders, children, and visitors away while operating a power tool. Distrac- tions can cause you to lose control. Electrical safety 4. A battery operated tool with integral bat- teries or a separate battery pack must be recharged only with the specified charger for the battery. A charger...

  • Page 4: Specific Safety Rules

    4 20. Use only accessories that are recom- mended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. Service 21. Tool service must be performed only by qualified repair personnel. Service or main- tenance performed...

  • Page 5

    5 aware of the time it takes for the blade to stop after switch is released. 6. Never hold piece being cut in your hands or across your leg. It is important to support the work properly to minimize body exposure, blade binding, or loss of control. 7. Hold tool by insulated gripping surfaces when per...

  • Page 6

    6 do not use dull or damaged blade. Unsharpened or improperly set blades pro- duce narrow kerf causing excessive friction, blade binding and kickback. Keep blade sharp and clean. Gum and wood pitch hard- ened on blades slows saw and increases potential for kickback. Keep blade clean by first removin...

  • Page 7: Save These Instructions

    7 clamp it down. Do not try to hold short pieces by hand! 18. Never attempt to saw with the circular saw held upside down in a vise. This is extremely dangerous and can lead to seri- ous accidents. 19. Warning: blade coasts to stop after switch is released. Contact with coasting blade can cause seri...

  • Page 8

    8 3. Caution - to reduce risk of injury, charge only makita rechargeable batteries marked on the charger label. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow. 5. Use of an attachment not recommended or sold by the battery charger manu...

  • Page 9: Battery Cartridge

    9 additional safety rules for charger & battery cartridge 1. Do not charge battery cartridge when temperature is below 10°c (50°f) or above 40°c (104°f). 2. Do not attempt to use a step-up trans- former, an engine generator or dc power receptacle. 3. Do not allow anything to cover or clog the charge...

  • Page 10: Functional

    10 functional description caution: • always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge • always switch off the tool before insertion or removal of the battery cartridge. • to r...

  • Page 11: Adjusting Depth of Cut

    11 time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • when you charge a battery cartridge from a just operated tool or a battery cartridge ...

  • Page 12: Switch Action

    12 switch action caution: • before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “off” position when released. To prevent the switch trigger from being accidentally pulled, a lock-off lever is provided. To start the to...

  • Page 13: Hex Wrench Storage

    13 hex wrench storage when not in use, store the hex wrench as shown in the figure to keep it from being lost. Operation caution: • be sure to move the tool forward in a straight line gently. Forcing or twisting the tool will result in overheating the motor and dangerous kickback, possibly causing s...

  • Page 14: Recycling The Battery

    14 to maintain product safety and reliability, repairs, any other maintenance or adjustment should be performed by makita authorized or factory service centers, always using makita replacement parts. En0001-1 recycling the battery the only way to dispose of a makita battery is to recycle it. The law...

  • Page 15: Memo

    Memo 15.

  • Page 16: Memo

    Memo 16.

  • Page 17: Makita U.S.A., Inc.

    17 first-class postage required post office will not deliver without proper postage. Makita u.S.A., inc. 14930 northam street la mirada, ca 90638-5753 fold cut.

  • Page 18: Mail This  Portion

    18 1. This product was purchased from: home center hardware/lumber store tool distributor industrial supply construction supply other ( ) 3. How did you learn about this product: magazine from dealer newspaper store display catalog radio exhibition from friend previous usage other ( ) 2. Use of the ...

  • Page 19: Factory Service Centers

    19 factory service centers 1-800-4-makita retain this portion for your records arizona 3707 e. Broadway rd., ste. 6 phoenix, az 85040 (602) 437-2850 california 41850 christy st. Fremont, ca 94538-5107 (510) 657-9881 14930 northam st. La mirada, ca 90638-5753 (714) 522-8088 1970 fulton avenue sacrame...

  • Page 20: Warning

    Warning some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline ...