1. DL manuals
  2. Makita
  3. Drill
  4. 6302H
  5. Instruction Manual

Makita 6302H Instruction Manual - Maintenance

Other manuals for 6302H: Parts Breakdown, Instruction Manual
Manual is about: Makita Drill Instruction Manual

Summary of 6302H

  • Page 1

    I n s t r u c t i o n m a n u a l warning: for your personal safety, read and understand before using. Save these instructions for future reference. W w w . M a k i t a t o o l s . C o m drill 13 mm (1/2”) model 6302h 13 mm (1/2”) model 6303h 002996 double insulation.

  • Page 2: Specifications

    2 specifications • manufacturer reserves the right to change specifications without notice. • specifications may differ from country to country. General safety rules usa002-2 (for all tools) warning: read and understand all instructions. Failure to follow all instructions listed below, may result in...

  • Page 3

    3 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged...

  • Page 4: Specific Safety Rules

    4 use proper extension cord: make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows t...

  • Page 5: Symbols

    5 symbols usd201-2 the followings show the symbols used for tool. V ....................... Volts a ....................... Amperes hz ..................... Hertz ................ Alternating current .................... No load speed .................... Class ii construction .../min..................

  • Page 6: Functional

    6 functional description caution: • always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action caution: • before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “off” position when...

  • Page 7: Operation

    7 installing side grip (auxiliary handle) always use the side grip to ensure operating safety. Install the side grip so that the teeth on the grip fit in between the protrusions on the tool barrel. Then tighten the grip by turning clockwise at the desired position. It may be swung 360 ° so as to be ...

  • Page 8: Maintenance

    8 however, the tool may back out abruptly if you do not hold it firmly. • always secure small workpieces in a vise or similar hold- down device. • avoid drilling in material that you suspect contains hidden nails or other things that may cause the bit to bind or break. Maintenance caution: • always ...

  • Page 9: Makita U.S.A., Inc.

    9 first-class postage required post office will not deliver without proper postage. Makita u.S.A., inc. 14930 northam street la mirada, ca 90638-5753 fold cut.

  • Page 10: Mail This  Portion

    10 1. This product was purchased from: home center hardware/lumber store tool distributor industrial supply construction supply other ( ) 3. How did you learn about this product: magazine from dealer newspaper store display catalog radio exhibition from friend previous usage other ( ) 2. Use of the ...

  • Page 11: Factory Service Centers

    11 factory service centers 1-800-4-makita retain this portion for your records arizona 3707 e. Broadway rd., ste. 6 phoenix, az 85040 (602) 437-2850 california 41850 christy st. Fremont, ca 94538-5107 (510) 657-9881 14930 northam st. La mirada, ca 90638-5753 (714) 522-8088 1970 fulton avenue sacrame...

  • Page 12: Warning

    Warning some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline ...