1. DL manuals
  2. Makita
  3. Chainsaw
  4. DCS34
  5. Instruction Manual

Makita DCS34 Instruction Manual

Manual is about: Makita DCS 34 Chain Saw: User Guide

Summary of DCS34

  • Page 1

    Important: read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! Dcs34 dcs4610 instruction manual.

  • Page 2

    Table of contents page packing ................................................................................ Delivery inventory ..............................................................3 symbols ..............................................................................3 safety precaution...

  • Page 3

    3 delivery inventory 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Assembly tool 6. Instruction manual (not shown) in case one of the parts listed should not be included in the delivery inventory, please consult your sales agent. Symbols you will note the following symbols on t...

  • Page 4

    4 4 3 1 2 3 4 5 6 7 safety precautions intended use power chain saws this power chain saw may be used only for sawing wood out of doors. It is intended for the followung uses depending on its class: - professional and mid-class: use on small, medium and large trees: felling, limb removal, cutting to...

  • Page 5

    5 6 5 7 9 8 fuels / refuelling - stop the engine before refuelling the chain saw. - do not smoke or work near open fires (5). - let the engine cool down before refuelling. - fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. Always w...

  • Page 6

    6 kickback - when working with the chain saw dangerous kickbacks may occur. - kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (0). - this causes the saw to be thrown back toward the user with great force and out of control. Risk of inj...

  • Page 7

    7 - be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). - when cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped. For this reason use the lower edge of the bar whenever possi...

  • Page 8: Service

    8 service transport and storage - when changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inadvertent start of the chain. - never carry or transport the chain saw with the chain run- ning. - when transporting the chain saw over long distanc...

  • Page 9

    9 stroke volume cm 3 33 45, bore mm 37 43 stroke mm 3 max. Power at speed kw / /min ,3 / 9.000 ,7 / 9.000 max. Torque at speed nm / /min ,7 / 6.500 ,4 / 6.500 idling speed / max. Engine speed with guide bar and chain /min .800 / .00 .600 / .600 coupling speed /min 3.900 sound pressure level l pa av ...

  • Page 10

    0 1 2 3 4 5 position the guide bar (6). Make sure that the pin (7) of the chain tightener is in the hole on the guide bar. Turn the chain adjusting screw (4) to the left (counterclockwise) until the pin (5) is at the left stop. Mounting the guide bar and saw chain use the universal wrench delivered ...

  • Page 11

    2 3 8 13 2 8 12 8 10 11 9 pull the chain (8) around the sprocket nose (12) of the guide bar in the direction of the arrow. Lift the chain (8) over the sprocket (9). Using your right hand, guide the chain into the top guide groove on the guide bar (10). Note that the cutting edges along the top of th...

  • Page 12

    2 checking the chain tension the tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. While doing so the chain brake must be released. Check the chain tension frequently - new chains tend to get longer during use! When ch...

  • Page 13

    3 fuel caution: this saw is powered by mineral-oil products (gasoline (petrol) and oil). Be especially careful when handling gasoline (petrol). Avoid all flame or fire. Do not smoke (explosion hazard). Fuel mixture the engine of the chain saw is a high-efficiency two-stroke engine. It runs on a mixt...

  • Page 14: Waste Oil

    4 a b fuel/oil mixture chain oil refuelling follow the safety precautions! Be careful and cautious when handling fuels. The engine must be switched off! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel or oil tank. Unscrew the cap and fill the tank with fuel (fue...

  • Page 15

    5 1 2 checking the chain lubrication never work with the chain saw withoute sufficient chain lubrica- tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: start ...

  • Page 16

    6 1 5 6 2 3 4 a starting the engine start the chain saw only after having assembled it com- pletely and inspected! Move at least 0 feet (3 m) away from the place where you fuelled the saw. Make sure you have a good footing, and place the saw on the ground in such a way that the chain is not touching...

  • Page 17: Service

    7 checking the chain brake do not work with the chain saw without first checking the chain brake! Start the engine as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact). Grasp the tubular handle firmly with one han...

  • Page 18

    8 maintenance sharpening the saw chain caution: before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „replacing the spark plug“). Always wear protective gloves! The chain needs sharpening when: the sawdust produced when sawing da...

  • Page 19

    9 d files and how to work with them sharpen using a special file holder with a saw chain round file dia. 4.0 mm. Normal round files are not appropriate for this work. See „accessories“ for the order number. The file should cut only when pushed forwards (arrow). Lift the file when leading it backward...

  • Page 20: Service

    0 cleaning the brake band and sprocket interior caution: before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „replacing the spark plug“). Always wear protective gloves! Caution: start the chain saw only after having assembled it...

  • Page 21: Service

    7 8 replacing the suction head the felt filter (9) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel flow to the carbure- tor. To remove the suction head for replacement, pull it out through the tank filler...

  • Page 22

    1 0,5 mm replacing the spark plug caution: do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. Wear protective gloves! The spark plug must be replaced in case of damage to the insul...

  • Page 23

    3 instructions for periodic maintenance to ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the p...

  • Page 24

    4 spare parts reliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts used. Use only original makita parts, marked only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning a...

  • Page 25

    5 1 2 3 4 6 14 16 15 17 18 19 7 5 8 10 10 9 pos. Makita-no. Qty. Denomination 44 035 66 sprocket nose bar 35 cm (4“) 58 09 65 saw chain 3/8“ for 35 cm 44 040 66 sprocket nose bar 40 cm (6“) 58 09 656 saw chain 3/8“ for 40 cm 3 95 00 630 chain protection for 30-35 cm 95 00 640 chain protection for 40...

  • Page 26

    6.

  • Page 27

    7 eu conformity declaration the undersigned, tamiro kishima and rainer bergfeld, as authorized by dolmar gmbh, declare that the makita machines, type: 036/037 eu prototype test certificate no. Dcs34 m6 08 01 24243 082 dcs4610 m6 08 01 24243 082 manufactured by dolmar gmbh, jenfelder str. 38, 045 ham...

  • Page 28

    8 form: 995 707 676 (.08 gb) specifications subject to change without notice to find your local distributor, please visit www.Makita-outdoor.Com makita werkzeug gmbh postfach 70 04 0 d-004 hamburg germany.