- DL manuals
- Makita
- Power Tool
- DJV142
- Instruction Manual
Makita DJV142 Instruction Manual
Summary of DJV142
Page 1
1 english ( o rigina l in st ruct ions) instruction manual important: read before using. Cordless jig saw djv142 djv182 014104.
Page 2: Specifications
2 english (original instructions) specifications model djv142 djv182 length of stroke 26 mm 26 mm wood 135 mm 135 mm mild steel 10 mm 10 mm max. Cutting capacities aluminum 20 mm 20 mm strokes per minute (min -1 ) 800 - 3,500 800 - 3,500 overall length 264 mm 266 mm net weight 2.5 kg 2.6 kg rated vo...
Page 3: General Power Tool Safety
3 warning: • the vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used. • be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of u...
Page 4: Cordless Jig Saw Safety
4 13. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 14. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpect...
Page 5: Save These Instructions.
5 11. Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece. 12. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 13. Do not operate the tool at no-load unnecessarily. 1...
Page 6: Functional Description
6 functional description caution: • always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 1 2 3 014154 caution: • always switch off the tool before installing or removing of the ba...
Page 7
7 position cutting action applications for cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood. Small orbit cutting action for cutting mild steel, aluminum and hard wood. For cutting wood and plywood. For fast cutting in aluminum and mild steel. Large orbit cutting a...
Page 8: Assembly
8 assembly caution: • always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing saw blade caution: • always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may c...
Page 9: Operation
9 anti-splintering device 2 1 014121 for splinter-free cuts, the anti-splintering device can be used. To install the anti-splintering device, move the tool base all the way forward and fit it from the back of tool base. When you use the cover plate, install the anti- splintering device onto the cove...
Page 10
10 with the base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). 1 2 3 014112 to tilt the base, loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the bevel slot in the base. 1 2 3 4 5 6 014123 t...
Page 11
11 metal cutting always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear. The underside of the workpiece can be greased instead of using a coolant. Rip fence set (optional accessory) caution: • always be sure that the tool is switched off an...
Page 12: Maintenance
12 install the guide rail adapter on the rail of the guide rail. Insert the rule bar into the square hole of the guide rail adapter. Put the base to the side of the guide rail, and secure the bolt securely. 1 2 3 014153 caution: • always use blades no. B-8, b-13, b-16, b-17 or 58 when using the guid...
Page 13
13.
Page 14
14.
Page 15
15.
Page 16
16 www.Makita.Com makita jan-baptist vinkstraat 2, 3070, belgium makita corporation anjo, aichi, japan 885228a225.