- DL manuals
- Makita
- Saw
- DPC6410 (UK)
- Instruction And Safety Manual
Makita DPC6410 (UK) Instruction And Safety Manual - page 27
27
Cutting attachment in
central / side position
NOTE: The Power Cut is delivered with the cutting attachment
mounted in the middle position (1). For cutting up against ob-
stacles, such as curbs or walls, the cutting attachment can be
mounted to one side (2). Use this position only when actually
necessary, and afterwards return the cutting attachment to the
middle position
In this position the Power Cut has better balance, is easier to
guide, and is not as fatiguing for the operator.
Use the combination tool (8) to lever out the stop pin (9) as
shown in the illustration, until the protective hood (11) can be
turned.
NOTE: The turn stop (7) is deactivated when the stop pin (8) is
removed. This permits the hood (11) to be turned farther than
the turn stop (7).
Unscrew the grip (10) and turn the protective hood (11) as
shown in the illustration.
Disengage the V-belt (12) and remove the cutting attach-
ment.
NOTE: The illustration shows the V-belt for models DPC6410
- 7321).
8
9
10
11
12
Repositioning the cutting attachment
Loosen nuts (5).
Loosen the tightening screw (3) (counter-clockwise) until the
end of the screw (4) is visible in the gap.
Loosen and unscrew the screw (detail X, only for DPC8112).
Unscrew the nuts (5) and remove the cover (6).
Summary of DPC6410 (UK)
Page 1
Warning! Read and understand this manual. Always follow safety precautions in the instruction and safety manual. Improper use can cause serious injury! The engine exhaust from this product contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. ...
Page 2
2 emissions component defect warranty coverage makita u.S.A, inc warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the u.S. Environmental protection ...
Page 3
3 packing your makita power cut is packed in a cardboard box to pre- vent shipping damage. Cardboard is a basic raw material and is consequently reuseable or suitable for recycling (waste paper recycling). Table of contents page packing ..................................................................
Page 4
4 6 5 4 3 2 1 delivery inventory 1. Power cut 2. Cutting disc 3. Adapter ring 0.8"/1.0" (not in the general scope of delivery. Country-specific) 4. Screwdriver (for carburetor adjustment) 5. Offset screwdriver 6. Universal wrench 13/19 7. Instruction manual (not shown) symbols you will notice the fo...
Page 5
5 2 3 1 4 safety precautions intended use power cut use the power cut cutoff saw outdoors only, for trimming and cutting suitable materials, using cutting discs rated for this machine. Improper use: never use the cutoff saw cutting discs for grinding or sanding (using the side of the cutting disc to...
Page 6
6 7 6 5 9 8 30 m 3 meters = wearing protective equipment - always wear safety shoes or boots (g) with steel toes, non-skid soles, and leg protectors when working with the power cut. Safety shoes equipped with a protective layer provide protection against cuts and ensure a secure footing. - always we...
Page 7
7 10 11 13 12 min. 5 m 14 ● maintenance ● refuelling ● changing cutoff discs ● repositioning the cutting attachment ● stopping work ● transport ● putting out of function cutoff discs - the protection hood must always be on! Change discs only with the engine off! - there are two basic types of cutoff...
Page 8
8 18 16 17 15 kickback and lock-in - when working with the power cut there is a danger of kickback and lock-in. - kickback occurs when the top of the cutting disc is used for cutting (15). - this causes the power cut to be thrown back toward the user with great force and out of control. Risk of inju...
Page 9
9 19 20 21 when using synthetic resin cutting discs, always ob- serve the following: caution: - synthetic resin cutting discs can absorb moisture. This moisture can cause the disc to become unbalanced at high speed. This imbalance can cause the disc to break. - do not cool resin cutting discs with w...
Page 10
10 23 26 25 24 in wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water. Makita offers the right accessories for all wet cutting applications (see also "special accessories"). - remove foreign objects such as sand, stones and nails found within the working area. Cautio...
Page 11: Service
11 27 28 29 service maintenance - before performing maintenance work switch off the power cut (27) and pull out the plug cap. - allow the power cut to cool off before doing any mainte- nance work (burn hazard)! - always check the power cut before using it to make sure that it is in good working orde...
Page 12
12 technical data displacement cu in (cm 3 ) 3.9 (64) 4.5 (73) bore in (mm) 1.85 (47) 1.97 (50) stroke in (mm) 1.46 (37) 1.46 (37) max. Power hp (kw) 4.4 (3.2) 5.6 (4.2) max. Torque nm 4.0 5.0 idling speed 1/min 2,500 2,500 clutch engagement speed 1/min 3,800 3,800 engine speed limitation 1/min 9,35...
Page 13
13 denomination of components (illustration shows model dpc7311) 1 handle 2 filter cover for air filter and spark plug cap 3 cover lock 4 tubular handle 5 muffler 6 protection hood 7 grip 8 v-belt tension adjusting screw 9 retaining nuts 10 stand 11 carburetor adjustment opening 12 identification pl...
Page 14
14 place the spring washer (8) on the arbour and insert the screw (9) and tighten by hand. Turn the disc slowly until the stop hole of the v-belt pulley is visible in the cutting arm cover (10). Insert the allen key (2) as far as it will go. The shaft is now blocked. Tighten the screw with the combi...
Page 15
15 note: the two fastening nuts (11) must be loosened before tightening the v-belt or checking the tension. To increase the belt tension, turn the tightening screw (12) to the right (clockwise) with the combination wrench included with the power cut. The belt tension is correctly adjusted when the n...
Page 16
16 fuels caution: the power cut uses mineral-oil products (gasoline and oil). Be especially careful when handling gasoline. Do not smoke. Do not allow gasoline to come near flames, sparks or fire (explosion hazard). Fuel mixture the power cut is powered by a high-performance two-stroke engine. It ru...
Page 17
17 refuelling important: follow the safety precautions! Be careful and cautious when handling fuels. The engine must be turned off and cooled down! Carefully clean the area around the fuel-tank filler neck to keep dirt from getting in the tank. Place the unit on its side on an even surface. Unscrew ...
Page 18
18 starting the engine this model is fitted with a semiautomatic decompression valve (1) to make starting easier. Depressing it reduces the force needed for compression, so little force is needed to accelerate the engine to its starting speed. The high pressure in the combustion chamber after the fi...
Page 19
19 stopping the engine push the combination switch (10) down to position . Grasp the tubular handle firmly with one hand and press the power cut against the ground. Place the tip of your left foot in the rear handle. Pull the starter cable strong and rapidly until you hear the first audible ignition...
Page 20
20 adjusting the carburetor note: the grinding parts are equipped with an electronic ignition to limit the speed. At the factory the idling speed has been set to approx. 2500 rpm, but the running-in process of a new engine may require slight readjustment of the idling speed. For correct adjustment o...
Page 21: Service
21 maintenance caution: before doing any work on the power cut turn off the engine, remove the cutting disc, pull the plug cap off the spark plug and wear protective gloves! Caution: start the power cut only after complete assembly and inspection. Important: because many of the parts and assemblies ...
Page 22
22 cleaning the protection hood over time, the inside of the protective hood can become caked with material residue (especially from wet cutting), which if allowed to accumulate can hinder the free rotation of the cut- ting disc. For this reason the hood must be cleaned out from time to time. Take o...
Page 23
23 pre-filter (foam with air-filter oil) only for models dpc8111 and 8112 clean or replace (when cutting with high dust amounts): • daily or at least every • 4 operating hours, or • 8 tank fillings, or • 8 litres fuel mixture. Clean or replace (when cutting wet, or when cutting steel): • weekly or a...
Page 24
24 checking the ignition spark insert the combination wrench (9) between the hood and cyl- inder only as shown. Caution! Do not insert the combination tool into the spark plug hole, but make contact only with the cylinder (otherwise you may damage the engine). Using insulated pliers, hold the spark ...
Page 25
25 replacing the starter cable remove four screws (14). Remove starter housing (15). Unscrew two screws (16) and carefuly remove the air guide (17) from the starter housing (15). Proceed in the order (a - b - c - d). Remove all pieces of cable (18). Thread in a new starter cable (dia 4.0 mm, length ...
Page 26
26 replacing the return spring remove the starter housing (see “replacing the starter cable”). Take the air guide off the starter housing (see “replacing the starter cable”). Take off circlip (1) (circlip pliers, see “accessories”). Remove the cable pulley (2). Unscrew screw (3). Evenly lever the re...
Page 27
27 cutting attachment in central / side position note: the power cut is delivered with the cutting attachment mounted in the middle position (1). For cutting up against ob- stacles, such as curbs or walls, the cutting attachment can be mounted to one side (2). Use this position only when actually ne...
Page 28
28 13 14 15 press the cutting attachment (13) onto the drive arm in the side position. Guide the v-belt (14) over the v-belt pulley (15). Note: the illustration shows the v-belt for models dpc6410 - 7321). Put the guard plate (16) on. Screw on nuts (17) and tighten by hand. To tighten the v-belt see...
Page 29
29 diamond cutting discs (1) makita diamond cutting discs meet the highest demands in working safety, ease of operation, and economical cut- ting performance. They can be used for cutting all materials except metal. The high durability of the diamond grains ensures low wear and thereby a very long s...
Page 30
30 instructions for periodic maintenance to ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be per- formed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform th...
Page 31
31 troubleshooting guarantee makita guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular guaran...
Page 32
32 extract from the spare parts list use only original makita parts. For repairs and replacement of other parts, see your makita service center. Dpc6410, 6411 dpc7310, 7311, 7320, 7321 dpc8111, 8112 32 31 29 30 22 28 * 20
Page 33
33 extract from the spare parts list use only original makita parts. For repairs and replacement of other parts, see your makita service center. Pos. Makita-no. Qty. Denomination synthetic resin cutting disc 1 966 121 150 1 cutting disc for steel, dia. 300/20 mm (12"/0.8") 966 141 150 1 cutting disc...
Page 34
34 emissions component defect warranty coverage makita u.S.A, inc garantit à l’acheteur au détail initial et à chaque propriétaire ultérieur que cet équipement utilitaire est conçu, construit et équipé en conformité, à la date d’achat initiale, à toutes réglementations applicables de l’ u.S. Environ...
Page 35
35 sommaire page emballage ..........................................................................35 etendue de la fourniture ..................................................36 symboles ...........................................................................36 instructions de sÉcuritÉ utilis...
Page 36
36 6 5 4 3 2 1 etendue de la fourniture 1. Découpeuse 2. Disque à découper 3. Bague d’adaptation 0.8"/1.0" (pas toujours fournie, en fonction du pays) 4. Tournevis (pour carburateur) 5. Tournevis coudé 6. Outillage de montage 13/19 7. Notice d’emploi (sans illustration) symboles vous rencontrerez le...
Page 37
37 2 3 1 4 instructions de sÉcuritÉ utilisation conforme aux prescriptions découpeuse la découpeuse ne doit être utilisée en plein air que pour découper / tronçonner des matériaux adéquats au moyen du disque à découper autorisé pour l’appareil. Méthode de travail non-autorisée : les disques à découp...
Page 38
38 7 6 5 9 8 30 m 3 mètres = porter l’équipement de protection - des gants ou des bottes de sécurité (g) à semelle crantée, une casquette en acier et un protège-jambe doivent être portés pendant l’utilisation de la découpeuse. Les chaussures de sécurité avec des recouvrements anti-coupure offre une ...
Page 39
39 10 11 13 12 min. 5 m 14 ● maintenance ● ravitaillement ● remplacer le disque à découper ● démonter le dispositif de découpage ● pause de travail ● transport ● mise hors service disques à découper - le capot de protection doit toujours être monté. Ne remplacer le disque à découper que lorsque le m...
Page 40
40 18 16 17 15 rebond (kickback) et freinage - un rebond ou freinage dangereux peut se produire en travaillant avec la découpeuse. - le rebond se produit lorsque la partie supérieure du disque est utilisé pour découper (15). - la découpeuse est incontrôlée, accélérée et lancée en avant avec une gran...
Page 41
41 19 20 21 a observer impérativement en cas d’utilisation de dis- ques à découper en résine synthétique attention: - les disques à découper en résine synthétique ont la pro- priété d’absorber l’humidité. Un déséquilibre survient dû à l’absorption d’humidité lors de la rotation rapide du disque à dé...
Page 42
42 23 26 25 24 disque à découper (refroidissement), pour un meilleur contrôle visuel et pour éviter un dégagement de poussière excessif, il est préférable de découper au mouillé plutôt qu’à sec. Pour cela, le disque à découper doit être arrosé d’eau de manière égale des deux côtés. Dans la gamme mak...
Page 43: Service
43 27 28 29 service maintenance - pour tous les travaux de maintenance, arrêter la décou- peuse (27) et retirer la fiche de la bougie! - laisser refroidir la découpeuse avant les travaux d‘entre- tien (risque de brûlure)! - vérifier avant de commencer à travailler si l’état de la dé- coupeuse est fi...
Page 44
44 caractéristiques techniques dpc8111 dpc8112 dpc6410 dpc6411 dpc7310, 7320 dpc7311, 7321 cylindrée cu in (cm 3 ) 3.9 (64) 4.5 (73) alésage in (mm) 1.85 (47) 1.97 (50) course in (mm) 1.46 (37) 1.46 (37) puissance max. Hp (kw) 4.4 (3.2) 5.6 (4.2) couple max. Nm 4.0 5.0 vitesse de rotation à vide 1/m...
Page 45
45 désignation des pièces (le dessin montre le modèle dpc7311) 1 poignée 2 couvercle de filtre pour filtre à air et fiche de bougie 3 pièce de verrouillage du couvercle 4 poignée-étrier 5 silencieux 6 capot de protection 7 poignée 8 vis de réglage pour la tension de courroie 9 ecrous de fixation 10 ...
Page 46
46 poser le disque de contrainte (8) sur l’arbre, visser la vis (9) à l’intérieur et la serrer à la main. Tourner lentement le disque à découper jusqu’à ce que le trou d’arrêt de la poulie à courroie trapézoïdale soit visible dans le couvercle de l’adaptateur de coupe (10). Enfoncer entièrement le t...
Page 47
47 note: pour tendre la courroie et pour vérifier la tension, il faut dévisser les écrous de fixation (11). Pour augmenter la tension, tourner la vis de tension (12) vers la droite (dans le sens des aiguilles) au moyen de la clé combinée comprise dans la fourniture. La courroie est correctement régl...
Page 48
48 carburants attention: l’appareil est utilisé avec des produits d’huiles minérales (essence et huile)! Votre attention est requise lorsque vous manipulez l’es- sence. Il est interdit de fumer et tout feu immédiat n’est pas autorisé (risque d’explosion). Mélange carburant le moteur de la découpeuse...
Page 49
49 remplissage des réservoirs attention: respecter imperativement les regles de securite! La manipulation de carburants exige une manipulation avec précaution et prudence. Opération à effectuer uniquement lorsque le moteur est arrêté et refroidi! Bien nettoyer autour de la zone de remplissage pour é...
Page 50
50 démarrer le moteur le modèle est équipé d’une soupape de décompression (1) semi-automatique pour faciliter le démarrage. En enfonçant la soupape de décompression, le travail de compression est réduit et le moteur accélère pour atteindre son régime de démarrage en déployant le moindre effort sur l...
Page 51
51 arrêter le moteur pousser le commutateur combiné (10) vers le bas en posi- tion . Tenir la poignée-étrier à pleine main et appuyer la découpeuse contre le sol. Poser la pointe du pied gauche dans le pare-main. Tirer vite et fort sur le cordon de lancement, jusqu’au dé- clenchement du premier allu...
Page 52
52 réglage du carburateur remarque: les découpeuses sont équipées d’un allu- mage électronique à limitation de vitesse de rotation. Le régime de ralenti est préréglé en usine sur env. 2.500 1/min; il se peut néanmoins que la procédure de rodage d’une nouvelle machine exige une léger rajustage du rég...
Page 53: Service
53 travaux de maintenance attention: pour tout travail sur la d´copeuse, il est impératif d’arrêter le moteur, de retirer le disque `découper, de tirer la cosse de bougie et de porter les gants de protection! Attention: la découpeuse ne peut être mise en marche qu’après le montage complet! Important...
Page 54
54 nettoyer le capot de protection a l’intérieur de la tôle de protection se constituent des dépôts de matière (notamment lors du découpage au mouillé) susceptibles d’empêcher la rotation du disque à découper. Démonter le disque à découper et le disque de pression. Enlever les dépôts de découpe à l’...
Page 55
55 pré-filtre (mousse avec huile pour filtre à air) uniquement pour les modèles dpc8111 et 8112 nettoyage ou remplacement (pour les découpes avec fort dégagement de poussières): • une fois par jour ou au plus tard après • 4 heures de service ou • 8 pleins ou • la consommation de 8 litres de mélange....
Page 56
56 vérification de l’étincelle d’allumage n’introduire la clé combinée (9) entre le capot et le cylindre que comme montré sur la figure. Attention! Ne pas introduire la clé dans le trou de bougie, établir seulement un contact avec le cylindre (sinon risque de détérioration du moteur). Presser contre...
Page 57
57 remplacement du cordon de lancement serrer les quatre vis (14). Retirer le carter du démarreur (15). Dévisser les deux vis (16) et retirer avec précaution la canali- sation d’air (17) du carter du démarreur (15), en suivant l’ordre donné (a - b - c - d). Enlever les anciens restes de cordon (18)....
Page 58
58 remplacement du ressort de rappel retirer le carter du démarreur (cf. Chapitre « remplacer le cordon de lancement »). Enlever la canalisation d’air du carter du démarreur (cf. Chapitre « remplacer le cordon de lancement »). Enlever le circlip (1) (pince pour les circlips extérieurs, voir accessoi...
Page 59
59 dispositif de coupe en positon médiane / posi- tion extérieure attention: le dispositif de découpage a été monté par l’usine pour le montage en position médiane (1). En cas d’obstacles se trouvant à toute proximité du tracé du découpage (par exemple bordure ou murs), le dispositif de découpage pe...
Page 60
60 16 17 18 poser le couvercle (16). Visser les écrous (17) et les serrer à la main. Tendre la courroie comme décrit au chapitre «tendre la courroie / contrôler la tension». Visser et serrer à bloc la vis (détail x, uniquement sur le mo- dèle dpc8112). Serrer bien les écrous (17) avec la clé combiné...
Page 61
61 disques à découper en diamant (1) en vue de satisfaire les exigences en matière de sécurité, de confort de travail et de fournir une solution économique lors des découpages, la gamme makita contient des disques à découper au diamant. Elles servent au découpage de toutes les matières à l’exception...
Page 62
62 indications de maintenance et d’entretien périodiques pour obtenir une longue durée de vie et pour éviter des détériorations, il faut effectuer régulièrement les travaux de maintenance décrits ci-après. Des demandes en garantie ne pourront être acceptées que si les travaux ont été effectués régul...
Page 63
63 recherche de pannes panne système observation origine la découpeuse ne démarre pas embrayage moteur tourne panne au niveau de l’embrayage disque à découper tourne carburateur, disque à découper tourne réglage du ralenti incorrect, au ralenti accouplement embrayage bloqué moteur ne démarre pas sys...
Page 64
64 extrait de la liste des pièces de rechange n’utilisez que des pièces de rechange d’origine makita. Pour les réparations et la rechange pour d’autres pièces, votre atelier spécialisé makita est compétent. Dpc6410, 6411 dpc7310, 7311, 7320, 7321 dpc8111, 8112 32 31 29 30 22 28 * 20
Page 65
65 pos. N°makita pcs. Désignation disque à découper à la résine 1 966 121 150 1 pour l’acier, diam. 300/20 mm (12"/0.8") 966 141 150 1 pour l’acier, diam. 350/20 mm (14"/0.8") 966 144 150 1 pour l’acier, diam. 350/25,4 mm (14"/1.0") 966 161 150 1 pour l’acier, diam. 400/20 mm (16"/0.8") 1 966 121 12...
Page 66
66.
Page 67
67.
Page 68
Specifications subject to change without notice changements sans préavis form: 995 704 732 (1 1.07 gb, f) makita u.S.A., inc. 14930 northam street la mirada, ca 90638-5753 makita canada inc. Dolmar division 1950 forbes street whitby, ontario canada, l1n 7b7.