Modfamily eyetrack TK302A Quick Reference Manual - page 2
o
If installing tracking through your computer, you will be prompted for a user name and password,
which is “admin” for both.
•
The device can be used outside the United States wherever a GSM network is enabled, for example T Mobile
international plan. GSM network is common in Europe and many other countries throughout the world.
•
There is an available App for both Android and IOS called “Tracker Home”.
•
Battery: Charge the battery using the included charger plus about 8-12 hours before use. The battery has up
to 180 hours of standby time once fully charged, however you should charge the battery regularly.
•
Basic troubleshooting: See manual, page 28
Text Message Device Code Commands
For these commands, don’t type any of the “+” signs or the where “space” is shown as a word – just insert a space. All
codes should be texted from an Admin’s Cell Phone.
ADMIN SETUP: This command is used for the cell phone that
will control the device and be the SOS contact for that button
on the unit:
•
Text admin+password+space+admin cell phone
number
For roaming purposes, may need to include your
country code ahead of the cell phone number, plus a
“1” following this code. (U.S. country code is 011).
CONTACTS SETUP:
These are 3 phone numbers the device can
call using the push buttons on the device:
•
Set up device button 1 (dorsal Jin on EyeTrak):
Text “contact”+space+”one”+password+space
+phone number; device replies, “contact one ok”
•
Set up device button 2 (left pectoral Jin on
EyeTrak) and device button 3 (tail/caudal Jin on
EyeTrak) using the same command, only replace
“one” with either “two” or “three”.
•
Delete Contacts (deletes all at once): Text
“nocontact+space+password”
AUTO TRACK CONTINUOUSLY – TIME INTERVALS: Tells the
device to send back its location continuously in chosen time
intervals.
•
Text Oix030s005n+space+password to the
device
o
Note: “Jix” then 3 numeric time
characters, then a unit of time - either
seconds (“s”), minutes (“m”) or hours
(“h”), then space and password. Hence,
“Jix001h010n” + password means send
back device coordinates every hour for
10 hours.
•
Device replies with its longitude/latitude
coordinates
•
Text Oix030s***n +password will send device
location continuously (no end) until disabled.
CALL DEVICE: Puts the device into call mode to receive calls.
(Must have a data carrier plan already enabled).
•
Text call+password to the device; tracker replies
“call ok” and can now receive and make calls.
WALKIE TALKIE/CB RADIO DEVICE FEATURE
•
Text speak+password to the device; tracker
replies “speak ok” and device enabled for 2-way
talk.
SOS ALERT
•
Press SOS button on the device for 3 seconds
and it will text help me!+location info to all of
the authorized numbers and then dial them one
after another, stopping when any authorized
number answers the call or texts back “help
me” to the tracker.
EXCESSIVE DEVICE VIBRATION, JIGGLE OR SHOCK: Sends
message if it is excessively jiggled. Default mode is off.
•
To turn on “shock sensor/alarm”, text shock
+password to the device.
•
Device replies “Shock is activated!”
•
Upon being “shocked”, device sends text “Sensor
alarm” + location info to all authorized numbers.
•
Cancel shock mode/alarm by texting noshock
+password to the tracker.
MOVEMENT ALARM: Detect unwanted device movement, i.e.
can protect a valuable that should stay stationary.
•
Set Up: Leave device stationary for 10 minutes
with GPS signal being received.
•
Text “move”+password+space+0200 to the
device; tracker replies “move OK”
o
Note: “0200” means an area with a
radius of 200 meters
•
If device moves, texts
“Move”+latitude,longtitude to authorized phone
numbers every 3 minutes.
•
To cancel movement alarm, text
“nomove”+password