- DL manuals
- N-Tron
- Switch
- 1002MC-LX
- User Manual & Installation Manual
N-Tron 1002MC-LX User Manual & Installation Manual
Summary of 1002MC-LX
Page 1
(revised 2011-09-28) 1 1000 series gigabit media converter & industrial gigabit ethernet switch user manual & installation guide.
Page 2
(revised 2011-09-28) 2 industrial gigabit ethernet switch installation guide 1002mc-sx 1000basesx multimode fiber media converter 1002mc-lx-yy 1000baselx singlemode fiber media converter 1003gx2-sx 1000basesx multimode fiber switch 1003gx2-lx-yy 1000baselx singlemode fiber switch 1003gx2-b custom mi...
Page 3
(revised 2011-09-28) 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al usa 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a register...
Page 4
(revised 2011-09-28) 4 electrical safety warnings this equipment is suitable for use in class i, division 2, groups a, b, c, and d or non-hazardous locations only. This equipment must be used with a listed ul industrial power supply. A recognized or listed fuse, rated maximum 3a, minimum 30vdc, must...
Page 5
(revised 2011-09-28) 5 laser safety (1002mc and 1003gx2 models) caution: class 1 laser product. Do not stare into the laser!).
Page 6
(revised 2011-09-28) 6 environmental safety warnings warning: disconnect the power and allow to cool 5 minutes before touching. 1000 series industrial gigabit ethernet switches the 1000 series unmanaged industrial gigabit ethernet switches support high speed layer 2 switching between ports. This ser...
Page 7
(revised 2011-09-28) 7 package contents please make sure the package contains the following items: 1. 1000 series media converter or ethernet switch 2. Product cd contact your carrier if any items are damaged. Unpacking remove all the equipment from the packaging, and store the packaging in a safe p...
Page 8: Urmk
(revised 2011-09-28) 8 din-rail mounting install the unit in a standard din rail. Recess the unit to allow at least 2” of horizontal clearance for cat5e cable bend radius or 5” of horizontal clearance for fiber optic cable bend radius. To install the unit to 35mm industrial din rail, place the top e...
Page 9
(revised 2011-09-28) 9 front panel from top to bottom: green led lights when power is connected lnk/act link/activity led spd1000 1000 speed led leds: the table below describes the operating modes: led color description on power is applied. Off power is off. Lnk/act on link established, no activity ...
Page 10
(revised 2011-09-28) 10 applying power (top view) unscrew & remove the dc voltage input plug from the top header. Install the dc power cables into the plug (observing polarity on unit). Plug the voltage input plug back into the top header. Tightening torque for the terminal block power plug is 0.5 n...
Page 11
(revised 2011-09-28) 11 n-tron switch grounding techniques for 1000 series the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immu...
Page 12
(revised 2011-09-28) 12 connecting the unit for 10base-t ports, plug a category 3 (or greater) twisted pair cable into the rj45 connector. For 100/1000base-t ports, plug a category 5e (or greater) twisted pair cable into the rj45 connector. Connect the other end to the far end station. Verify that t...
Page 13
(revised 2011-09-28) 13 fcc statement this product complies with part 15 of the fcc-a rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired ope...
Page 14
(revised 2011-09-28) 14 1002mc - key specifications physical height: 4.0” (10.16 cm) width: 1.0” (2.54 cm) depth w/ typical sfp installed: 3.61” (9.165 cm) weight: 0.70 lbs (0.32 kg) din rail: 35 mm electrical input voltage: 10-30 vdc (regulated) input current: 200ma max. @ 24vdc (steady state) inru...
Page 15
(revised 2011-09-28) 15 gigabit fiber transceiver (sfp) characteristics fiber length 550m* with 50/125 µm 275m @ 62.5/125μm 10km** 40km** 80km** tx power min -9.5dbm -9.5dbm -2dbm 0dbm rx sensitivity max -17dbm -20dbm -22dbm -24dbm wavelength 850nm 1310nm 1310nm 1550nm assumed fiber loss 3.5 to 3.75...
Page 16
(revised 2011-09-28) 16 1003gx2 - key specifications physical height: 4.0” (10.16 cm) width: 1.0” (2.54 cm) depth w/ typical sfp installed: 3.61” (9.165 cm) weight: 0.7 lbs (0.32 kg) din rail: 35 mm electrical input voltage: 10-30 vdc (regulated) input current: 200ma max. @ 24vdc (steady state) inru...
Page 17
(revised 2011-09-28) 17 gigabit fiber transceiver (sfp) characteristics fiber length 550m* with 50/125 µm 275m @ 62.5/125μm 10km** 40km** 80km** tx power min -9.5dbm -9.5dbm -2dbm 0dbm rx sensitivity max -17dbm -20dbm -22dbm -24dbm wavelength 850nm 1310nm 1310nm 1550nm assumed fiber loss 3.5 to 3.75...
Page 18
(revised 2011-09-28) 18 1005tx - key specifications physical height: 4.0” (10.16 cm) width: 1.0” (2.54 cm) depth: 3.61” (9.165 cm) weight: 0.70 lbs (0.32 kg) din rail: 35 mm electrical input voltage: 10-30 vdc (regulated) input current: 230ma max. @ 24vdc (steady state) inrush current: 13 amp/0.61 m...
Page 19
(revised 2011-09-28) 19 regulatory approvals: safety: ul listed per ansi/isa-12.12.01-2007 (us and canada) and listed for use in class i, div 2, groups a, b, c, d, t4. Emi: en61000-6-4, en55011 - class a fcc title 47, part 15, subpart b - class a ices-003 – class a ems: en61000-6-2 en61000-4-2 (esd)...
Page 20
(revised 2011-09-28) 20 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller....