Summary of 202MC-SC
Page 1
(revised 2010-11-15) 1 200 series media converters installation guide.
Page 2: 202Mc-Sc
(revised 2010-11-15) 2 industrial ethernet switch installation guide 202mc-sc 202mc-st 202mce-sc-yy 202mce-st-yy where: yy = -15, -40, or -80
Page 3
(revised 2010-11-15) 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al 36609, usa all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a registe...
Page 4: Safety Warnings
(revised 2010-11-15) 4 safety warnings electrical safety warning: explosion hazardous, do not disconnect while circuit is live, unless area is known to be non- hazardous. Warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover remove...
Page 5
(revised 2010-11-15) 5 202mc & 202mce industrial ethernet media converters the 202mc and 202mce unmanaged industrial ethernet media converters support high speed layer 2 switching between ports. The 202mc is a 2 port unmanaged media converter switch that has 1 rj45 port and a multimode fiber optic u...
Page 6
(revised 2010-11-15) 6 package contents please make sure the ethernet switch package contains the following items: 1. 202mc/202mce ethernet media converter 2. N-tron product cd contact your carrier if any items are damaged. Installation read the following warning before beginning the installation: w...
Page 7
(revised 2010-11-15) 7 202mc/202mce half duplex setup while all rj45 port uses autonegotiation and autosensing, the 202mc/202mce fiber optic port is factory configured for full duplex operation. In the event half duplex operation is desired, follow these steps: 1. Remove the voltage input power plug...
Page 8
(revised 2010-11-15) 8 din-rail mounting install the unit in a standard din-rail. Recess the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius. Note: this unit may be mounted horizontally or vertically. To install the unit to 35 mm industrial din-rail - place the to...
Page 9
(revised 2010-11-15) 9 front panel from left to right: lnk link led for fiber optic port tx fiber optic transmit port rx fiber optic receive port act activity led for fiber optic port rj45 port auto sensing 10/100baset connections ! Red led indicates controller error green led lights when power is c...
Page 10
(revised 2010-11-15) 10 applying power (side view) unscrew & remove the dc voltage input plug(s) from the side header install the dc power cables into the plug(s) (observing polarity). Plug the voltage input plug(s) back into the side header. Tightening torque for the terminal block power plug is 0....
Page 11
(revised 2010-11-15) 11 n-tron switch grounding techniques the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emissio...
Page 12
(revised 2010-11-15) 12 rj45 connector crimp specifications please reference the illustration below for your cat5 cable specifications:.
Page 13
(revised 2010-11-15) 13 connecting the unit for 202mc and 202mce units, remove the dust cap from the fiber optic connectors and connect the fiber optic cables. The tx port on the unit should be connected to the rx port of the far end station. The rx port on the unit should be connected to the tx por...
Page 14
(revised 2010-11-15) 14 key specifications physical height: 2.13" (5.41 cm) width: 5.00" (12.70 cm) depth: 3.00" (7.62 cm) weight: ~ 1.2 lbs. (0.6 kg) (note: can be mounted horizontally or vertically) electrical input voltage: 10-30 vdc (regulated) input current: 190ma max. @ 24vdc (steady state) in...
Page 15
(revised 2010-11-15) 15 regulatory approvals: safety: suitable for use in class i, division 2, groups a, b, c, and d hazardous locations, or non-hazardous locations only. Emi: en55022 – class a fcc part 15 class a ems: en55024:1998 en61000-4-2:1995 en61000-4-3:1997 en61000-4-4:1995 en61000-4-5:1995 ...
Page 16
(revised 2010-11-15) 16 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller....