1. DL manuals
  2. N-Tron
  3. Switch
  4. 400 Series
  5. Installation Manual

N-Tron 400 Series Installation Manual - 405Tx

Manual is about: 400 Series Industrial Ethernet Switches

Summary of 400 Series

  • Page 1

    Rev 041008 1 400 series industrial ethernet switches installation guide.

  • Page 2: 405Tx

    Rev 041008 2 industrial ethernet switch installation guide 405tx 405fx-sc 405fx-st 405fxe-sc-yy 405fxe-st-yy where: yy = -15, -40, or -80

  • Page 3

    Rev 041008 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al 36609 usa all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a registered tradema...

  • Page 4: Safety Warnings

    Rev 041008 4 safety warnings electrical safety warning: do not disconnect while circuit is live, unless area is known to be non-hazardous. Warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover removed. Warning: do not work on equip...

  • Page 5

    Rev 041008 5 405fx, 405fxe, & 405tx industrial ethernet switches the 405tx and 405fx unmanaged industrial ethernet switches support high speed layer 2 switching between ports. The 405tx is an affordable 5 port unmanaged switch that is capable of auto negotiating 10/100 mb and half/full duplex commun...

  • Page 6

    Rev 041008 6 package contents please make sure the ethernet switch package contains the following items: 1. 405fx/405fxe/405tx ethernet switch 2. This installation guide contact your carrier if any items are damaged. Installation read the following warning before beginning the installation: warning ...

  • Page 7

    Rev 041008 7 405fx/405fxe half duplex setup while all rj45 ports are autosensing, the 405fx/405fxe fiber optic port is factory configured for full duplex operation. In the event half duplex operation is desired, follow these steps: 1. Remove the voltage input power plugs. 2. Remove the top cover (8 ...

  • Page 8

    Rev 041008 8 din-rail mounting install the unit in a standard din-rail. Recess the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius (2” for tx models). Note: this unit may be mounted horizontally or vertically. To install the unit to 35mm industrial din-rail - plac...

  • Page 9

    Rev 041008 9 front panel from left to right: lnk link led for fiber optic port (405fx/fxe only) tx fiber optic transmit port (405fx/fxe only) rx fiber optic receive port (405fx/fxe only) act activity led for fiber optic port (405fx/fxe only) x rj45crossover uplink port (405tx only) rj45 ports auto s...

  • Page 10

    Rev 041008 10 led’s: the table below describes the operating modes: led color description green power is applied off power is off ! Red controller hw error off no errors. Normal operation. Lnk green link between ports established off no link between ports act green data is active between ports off d...

  • Page 11

    Rev 041008 11 n-tron switch grounding techniques the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emissions (i.E. C...

  • Page 12

    Rev 041008 12 rj45 connector crimp specifications please reference the illustration below for your cat5 cable specifications:.

  • Page 13

    Rev 041008 13 connecting the unit for 405fx & 405fxe units, remove the dust cap from the fiber optic connectors and connect the fiber optic cables. The tx port on the 405fx should be connected to the rx port of the far end station. The rx port on the 405fx should be connected to the tx port of the f...

  • Page 14

    Rev 041008 14 key specifications physical height: 2.13" (5.41 cm) width: 5.00" (12.70 cm) depth: 3.00" (7.62 cm) weight: ~ 1.2 lbs. (0.6 kg) (note: can be mounted horizontally or vertically) electrical input voltage: 10-30 vdc (regulated) input current: 220ma max. @ 24vdc (steady state) inrush curre...

  • Page 15

    Rev 041008 15 regulatory approvals: safety: ul 1604 (us and canada) hazardous locations, class i, zone 2, group iic, t4a emi: en55022 – class a fcc part 15 class a ems: en55024:1998 en61000-4-2:1995 en61000-4-3:1997 en61000-4-4:1995 en61000-4-5:1995 en61000-4-6:1996 gost-r certified. Warranty: effec...

  • Page 16

    Rev 041008 16 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller. If a prod...