1. DL manuals
  2. N-Tron
  3. Switch
  4. 604MFX-ST
  5. Hardware Installation Manual

N-Tron 604MFX-ST Hardware Installation Manual - 604Mfx-St

Summary of 604MFX-ST

  • Page 1

    (revised 2010-11-15) 1 600 series industrial ethernet switches hardware installation guide.

  • Page 2: 604Mfx-St

    (revised 2010-11-15) 2 industrial ethernet switch installation guide 604mfx-st 604mfxe-st-15 604mfxe-st-40 604mfxe-st-80 608mfx-st 608mfxe-st-15 608mfxe-st-40 608mfxe-st-80

  • Page 3

    (revised 2010-11-15) 3 copyright, © n-tron corp., 2008 820 s. University blvd., suite 4e mobile, al usa 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a register...

  • Page 4: Safety Warnings

    (revised 2010-11-15) 4 safety warnings electrical safety warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover removed. Warning: properly ground the unit before connecting anything else to the unit. Units not properly grounded may ...

  • Page 5

    (revised 2010-11-15) 5 600 series industrial ethernet switch the n-tron 600 series are product derivatives of the osm/esm family jointly manufactured by siemens and n-tron. The n-tron 600 series switches supports high speed layer 2 switching between ports, and is housed in a ruggedized steel enclosu...

  • Page 6

    (revised 2010-11-15) 6 package contents please make sure the ethernet switch package contains the following items: 1. 600 series ethernet switch 2. Product cd contact your carrier if any items are damaged. Installation read the following warning before beginning the installation: warning the fxe uni...

  • Page 7

    (revised 2010-11-15) 7 600 series hazardous location installation requirements 1. Warning! Do not disconnect while circuit is live, unless area is known to be non-hazardous. 2. Warning! Install only in accordance with local & national codes of .Authorities having jurisdiction. 3. Class i, div 2 inst...

  • Page 8

    (revised 2010-11-15) 8 applying power 1. Unscrew the flange & remove the dc voltage input plug from the header. 2. Install the dc power cables into the plug(s) (observing polarity per the legend on the top of the unit). L1+ and l2+ are the +24v connections. M1 and m2 are the minus (-) returns for th...

  • Page 9

    (revised 2010-11-15) 9 connecting the standard ring remove the dust cap from the fiber optic connectors and connect the fiber optic cables. Please refer to the figure 1. Diagram. To begin the ring, the tx out-port #7 should be connected to the rx in-port #8 of the far end station. The rx in-port #7 ...

  • Page 10

    (revised 2010-11-15) 10 for 10/100 base-tx ports, plug a category 5 (or better) twisted pair cable into one the rj45 copper ports (1-6). Connect the other end to the far end station. Verify that the port led’s are on once the connection has been completed. For switch to switch or switch to repeater ...

  • Page 11

    (revised 2010-11-15) 11 608mfx ring manager 608mfx network segment redundancy figure 2 608m fx 608m fx standby m as te r fiber optic pair fiber optic pair fiber optic pair #7 #8 #7 #8 #7 #8 #7 #8 608m fx standby slave 608m fx 608m fx fiber optic pair fiber optic pair #7 #8 #7 #8 608m fx 608mfx ring ...

  • Page 12

    (revised 2010-11-15) 12 displays and operating controls led’s fault (red led) status meaning on the 604/608mfx has detected an error. The signaling contact opens at the same time. Off no errors detected by the 604/608mfx. Stby - standby (green led, 608mfx only) status meaning on the 608mfx standby f...

  • Page 13

    (revised 2010-11-15) 13 port led’s the display mode is indicated by the led pair labeled “display mode”, and the state is given by the legend on the front of the 600 series switch. To transition between these display modes, the select/set button must be pressed briefly (similar to left mouse click)....

  • Page 14

    (revised 2010-11-15) 14 “select/set” button the select/set” multi-functional button on the front panel of the 604/608mfx performs the following actions: pressing the button briefly (similar to left mouse click) transitions the display of the two display mode led’s. The current display mode is indica...

  • Page 15

    (revised 2010-11-15) 15 aging time the 604/608mfx monitors the age of the addresses it has learnt, and addresses that exceed a certain age (aging time, default setting = 40 sec), are deleted again by the switch. If a packet with a source address matching the address entry is received before the agin...

  • Page 16

    (revised 2010-11-15) 16 serial interface the 604/608mfx provides an eia-232 interface accessed via a 9 pin male connector (labeled v24 on the unit). This is used to access the command line interpreter (cli). Functions include setting the ip address, and other parameters (see network management users...

  • Page 17

    (revised 2010-11-15) 17 serial cable connect the serial com port of your pc and the 600 series switch using a normal null modem cable (or a straight through cable with a null modem adapter). You will require a cable with a 9-pin or 25-pin sub-d female connector for the pc end, and a 9-pin female sub...

  • Page 18

    (revised 2010-11-15) 18 troubleshooting 1. Make sure the power led (l1 and/or l2) is on. 2. Make sure the voltage is within specifications (18-32v@1a). 3. Make sure the fiber ports and tx ports are properly connected. 4. Verify that port led’s are on for connected ports. 5. Verify the status of the ...

  • Page 19

    (revised 2010-11-15) 19 key specifications physical height: 5.5" (13.65 cm) width: 8.55" (21.70 cm) depth: 2.75" (6.90 cm) weight: 3.08 lbs (1.4 kg) electrical input voltage: 18-32 vdc (redundant inputs) input current: 1.0a @ 24vdc inrush current: 10.5a / 7 ms @ 24vdc power consumption: 24 watts @24...

  • Page 20

    (revised 2010-11-15) 20 recommended wiring clearance: top: 1 " (2.54 cm) front: 4 " (10.16 cm) emissions and safety approvals: fcc part 15 class a ce, ul, fm class 1 div 2 groups a,b,c,d note: shielded cables must be used to meet emission standards. Dnv/det norske veritas (a-10136) ordering informat...

  • Page 21: N-Tron Limited Warranty

    (revised 2010-11-15) 21 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the data of purchase from n-tron or its authorized reseller....

  • Page 22

    (revised 2010-11-15) 22 and non-infringement, all of which are expressly disclaimed. N-tron neither assumes nor authorizes any other person to assume for it any other liability in connection with the sale, installation, maintenance or use of its products. N-tron shall not be liable under this warran...