1. DL manuals
  2. N-Tron
  3. Switch
  4. 900-N Series
  5. Installation & User Manual

N-Tron 900-N Series Installation & User Manual

Other manuals for 900-N Series: Features, Installation & User Manual

Summary of 900-N Series

  • Page 1

    900 series industrial ethernet switch installation & user’s guide.

  • Page 2

    Rev050908 2.

  • Page 3: 900B/900N

    Rev050908 3 industrial ethernet switch installation guide 900b/900n (3 slot enclosure and backplane) 900b-fp (filler panel for empty slots) 908tx (module) 902fx-sc (module) 902fx-st (module) 902fxe-sc-yy (module) 902fxe-st-yy (module) 904fx-sc (module) 904fx-st (module) 904fxe-sc-yy (module) 904fxe-...

  • Page 4

    Rev050908 4 copyright, © n-tron corp., 2008 n-tron corp. 820 s. University blvd., suite 4e mobile, al 36609 all rights reserved. Reproduction, adaptation, or translation without prior written permission from n-tron corp. Is prohibited, except as allowed under copyright laws. Ethernet is a registered...

  • Page 5: Safety Warnings

    Rev050908 5 safety warnings electrical safety warning: disconnect the power cable before removing the enclosure top. Warning: do not operate the unit with the top cover removed. Warning: do not work on equipment or cables during periods of lightning activity. Warning: do not perform any services on ...

  • Page 6

    Rev050908 6 900 series hazardous location installation requirements 1. Warning: explosion hazard. Do not disconnect unit while circuit is live, unless known to be non-hazardous. 2. Avertisement: risque d’explosion. Nepas de’brancher tant que le circuit est sous tension, a’moins qu’il s’ a gisse d’un...

  • Page 7

    Rev050908 7 900 series industrial ethernet switches the 900 series modular industrial ethernet switches support high speed layer 2 switching between ports. The 900b and 900n enclosures contain a three slot backplane that supports up to three modules. The 908tx, 902fx and 904fx modules are the availa...

  • Page 8

    Rev050908 8 package contents please make sure the ethernet switch package contains the following items: 1. 900 series ethernet switch 2. Installed modules 3. This installation guide contact your carrier if any items are damaged. Installation read the following warning before beginning the installati...

  • Page 9

    Rev050908 9 902fx/fxe & 904fx /fxe half duplex setup all 900 series fiber modules are factory configured for full duplex operation. The setting is controlled by jumper jp1 on the backplane. Note: most 100mbit fiber systems will be compatible with this full duplex setting. If half duplex operation is...

  • Page 10

    Rev05 d i f v t t t t d u o t h m o t o 0908 din-rail m install the un fiber optic c vertically. To install the the back of th the back (aw to remove t disengages f upward and t optional mo the 900 ser however, d mounting sol our 900 pan to a panel or our rack m mounting nit in a stand cable bend r ...

  • Page 11

    Rev050908 11 module configuration settings in order for the 900 series modules to communicate properly the chassis must be populated with modules from the top slot down as shown below. In addition, jp1 and jp2 jumpers (located on top side of all modules) must be configured as indicated below. Note: ...

  • Page 12

    Rev050908 12 908tx module from left to right: rj45 ports ports 1-8 auto sensing 10/100baset ports upper left led port link status upper right led portactivity status green led lights when power is connected note: at power cycle, all led’s flash on for approximately two seconds, and then return to pr...

  • Page 13

    Rev050908 13 902/904 fx & fxe module from left to right: tx fiber optic transmit port rx fiber optic receive port lnk link led (top led) for fiber optic port act activity led (bottom led) for fiber optic port green led lights when power is connected note: at power cycle, only the led’s on the first ...

  • Page 14

    Rev050908 14 applying power 1. Unscrew the flange & remove the dc voltage input plug(s) from the side headers. 2. Install the dc power cables into the plug(s) (observing polarity). 3. Tightening torque for the terminal block power plug is 0.22 nm/0.162 pound foot. 4. Plug the voltage input plug(s) b...

  • Page 15

    Rev050908 15 n-tron switch grounding techniques the grounding philosophy of any control system is an integral part of the design. N-tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emissions (i.E. Ce...

  • Page 16

    Rev050908 16 rj45 connector crimp specifications please reference the illustration below for your cat5 cable specifications:.

  • Page 17

    Rev050908 17 connecting the unit for 902 & 904 fx & fxe units, remove the dust cap from the fiber optic connectors and connect the fiber optic cables. The tx port on the 902 and/or 904 units should be connected to the rx port of the far end station. The rx port on the 902 and/or 904 units should be ...

  • Page 18

    Rev050908 18 key specifications physical height: 3.2" (8.13 cm) width: 7.1" (18.03 cm) depth: 4.1" (10.41 cm) weight: ~3.0 lbs (2.3 kg) (note: this unit may be mounted horizontally or vertically) electrical input voltage: 10-30 vdc (regulated) input current: 390 ma @ 24vdc (steady state) input rippl...

  • Page 19

    Rev050908 19 regulatory approvals: safety: listed as ul 1604 (us and canada) hazardous locations, class i, zone 2, group iic, t4a emi: en50081-1:1992, en55022 – class a fcc part 15 class a ems: en55024:1998 en61000-4-2:1995 en61000-4-3:1995 en61000-4-4:1995 en61000-4-5:1995 en61000-4-6:1995 note: sh...

  • Page 20

    Rev050908 20 ordering information pn description 900b industrial ethernet switch chassis with 3 slots for optional expansion modules 900-rm 19" rack mount kit 900-pm panel mount kit 908tx eight ports 10/100basetx (rj45) 902fx-xx two ports 100basefx multimode fiber 902fxe-xx-yy two ports 100basefx si...

  • Page 21

    Rev050908 21 n-tron limited warranty n-tron, corp. Warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from n-tron or its authorized reseller. If a produ...