Dm1400 & dm1800 upright vacuum operating instructions and repair parts list form no. 70720n 3/04 nacecare solutions printed in the u.S.A. Read this book this book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any ...
Page -2- n.A.C.E. Operator's manual - dm1400 & dm1800 operator safety instructions ............................................................................................................. 3 introduction & machine specifications ......................................................................
Page -3- n.A.C.E. Operator's manual - dm1400 & dm1800 operator safety instructions warning avertissement advertencia for the safe operation of this machine, read and understand all dangers, warnings and cautions. Look for these symbols: danger: if you do not follow the instructions in a danger, seve...
Page -4- n.A.C.E. Operator's manual - dm1400 & dm1800 save these instructions warning: to reduce the risk of fire, electric shock, or injury: 16. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt. 17. Do not use to pick up f...
Page -5- n.A.C.E. Operator's manual - dm1400 & dm1800 consignes de sÉcuritÈ de l'utilisateur avertissement pour utiliser cet appareil en toute sécurité, il faut lire et coprendre tous les consignes de danger, d'avertissement et d'attention. Soyez attentif aux symboles que voici. Danger: ne pas respe...
Page -6- n.A.C.E. Operator's manual - dm1400 & dm1800 16. Ne remassez pas de objets qui brûient ou fument comme les cigarettes, les allumettes ou les cendres chaudes. 17. Les poulies de la courroie peuvent devenir chaudes pendant l'utilisation normale. Pour prévenir des brûlures, évitez de toucher l...
Page -7- n.A.C.E. Operator's manual - dm1400 & dm1800 power supply 120v-60 cycle 120v-60 cycle vacuum motor 1050 watts 1050 watts brush rpm 4300 rpm 4300 rpm cord 50 ft. 3-wire 50 ft. 3-wire wheels (2) 2.7" x 1.25" 2.7" x 1.25" wand 21" extends to 33.5" 21" extends to 33.5" hose 1.5" x 18.5" 1.5" x ...
Page -8- n.A.C.E. Operator's manual - dm1400 & dm1800 grounding instructions preparation: the following are instructions for connection to the power supply and the electrical ground. This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine ha...
Page -9- n.A.C.E. Operator's manual - dm1400 & dm1800 instructions visant la mise a la terre preparation: consignes pour brancher l'appareil a la source d'energie et pour la mise à la terre. Cet appareil doit être mise à la terre afin d'eviter le risque de choc électrique. Cet appareil est pourvu d'...
Page -10- n.A.C.E. Operator's manual - dm1400 & dm1800 figure 2 figure 3 figure 5 figure 4 how to assemble the machine to assemble the machine, follow this procedure: 1. Remove the brush housing, vacuum bags, hose, wand, handle assembly, canister housing, and tools from the carton. 2. Remove the can...
Page -11- n.A.C.E. Operator's manual - dm1400 & dm1800 figure 7 figure 6 5. Install the wand assembly in the right rear canister housing (see figure 6, item a). 6. Position wand handle so that handle is towards the front of the machine (see figure 7, item a). 7. Attach hose to wand and canister (see...
Page -12- n.A.C.E. Operator's manual - dm1400 & dm1800 figure 9 the controls the handle release pedal (see figure 8, item a) the handle release pedal is on the lower left side of the machine. Press the pedal to release the handle and start the brush motor. The brush motor will not run unless the on/...
Page -13- n.A.C.E. Operator's manual - dm1400 & dm1800 figure 12 figure 13 canister door (see figure 12, item a) the canister door release is in the upper part of the canister housing. Lift to open door. Note: door will not close without a properly mounted filter bag. See page 11 for filter bag moun...
Page -14- n.A.C.E. Operator's manual - dm1400 & dm1800 how to operate the machine caution: to prevent damage to the machine, do not allow large objects to be pulled into the lower housing or the attachments. Note: the machine comes with a filter bag installed in the canister housing. Use the dm1400 ...
Page -15- n.A.C.E. Operator's manual - dm1400 & dm1800 maintenance warning: to prevent injury, always remove the electrical plug from the electrical outlet before doing any maintenance or repairs to the machine. Warning: maintenance and repairs must be done by authorized personnel only. Use only gen...
Page -16- n.A.C.E. Operator's manual - dm1400 & dm1800 figure 20 figure 21 how to change the filter cartridge change the filter cartridge whenever it is dirty or suction performance decreases. To change the filter cartridge, follow this procedure: 1. Make sure the on/off switch is in the "o" positio...
Page -17- n.A.C.E. Operator's manual - dm1400 & dm1800 figure 23 figure 24 how to change the drive belt warning: to prevent injury, unplug machine before cleaning or replacing brush. Brush may start suddenly and cause injury. To change the drive belt, follow this procedure: 1. Put the machine on its...
Page -18- n.A.C.E. Operator's manual - dm1400 & dm1800 the utv14 & utv18 upright vacuums have 3 brush performance indicator lights (see figure 25). They are green, yellow and red. They work in the following manner: normal operation: • the green light is on when the brush drive motor is on and the br...
Page -19- n.A.C.E. Operator's manual - dm1400 & dm1800 dm1400 & dm1800 upright vacuum repair parts list.
Page -20- n.A.C.E. Operator's manual - dm1400 & dm1800 n.A.C.E. Dm1400 & dm1800 drawing #1 upper canister assembly 3/04 1 2 3 4 5 6 7 8 5 9 11 10 12 13 14 15 16 17 18 19 20 22 21 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Page -21- n.A.C.E. Operator's manual - dm1400 & dm1800 1 53296a handle tube 1 1a 53199n handle, left 1 1b 53207n handle, right 1 1c 53320a on/off switch 1 1d 53315a pad, soft touch 1 1e 53318a power cord 1 1f 53233a receptacle, handle 1 2 53211n canister, rear 1 (incl. #4, 5, 6, 7, 28, 29, 30, 35, 3...
Page -22- n.A.C.E. Operator's manual - dm1400 & dm1800 n.A.C.E. Dm1400 & dm1800 drawing #2 brush housing assembly 3/04 1 2 3 4 5 6 7 8 9 8 10 11 12 13 14 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 37 13 34 35 36 13.
Page -23- n.A.C.E. Operator's manual - dm1400 & dm1800 part no. Description qty. 1 53231n cover asm., brush hsg. 14" 1 53232n cover asm., brush hsg. 18" 1 2 (cover asm. Include #2) 3 53245a pedal, brush height 1 4 53243a pivot asm., airway 1 (incl. 53236a; 53244a bracket, airway right; & 53243a brac...
Page -24- n.A.C.E. Operator's manual - dm1400 & dm1800 n.A.C.E. Dm1400 & dm1800 electrical schematic 3/04.
Page -25- n.A.C.E. Operator's manual - dm1400 & dm1800 notes.
Nacecare solutions u.S. Limited warranty this n.A.C.E. Industrial/commercial product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with n.A.C.E. Maintenance...