Form no. 70676n 3/04 nacecare solutions printed in the u.S.A. Read this book this book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your n.A.C.E.Machine could result in inj...
Page -2- n.A.C.E. Operator's manual - sm1200 & sm1600 table of contents operator safety instructions ................................................................................... 3 grounding instructions .............................................................................................
Page -3- n.A.C.E. Operator's manual - sm1200 & sm1600 operator safety instructions warning avertissement advertencia for the safe operation of this machine, read and understand all dangers, warnings and cautions. Look for these symbols: danger: if you do not follow the instructions in a danger, seve...
Page -4- n.A.C.E. Operator's manual - sm1200 & sm1600 save these instructions warning: to reduce the risk of fire, electric shock, or injury: 16. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt. 17. Do not use to pick up f...
Page -5- n.A.C.E. Operator's manual - sm1200 & sm1600 grounding instructions preparation: the following are instructions for connection to the power supply and the electrical ground. This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine ha...
Page -6- n.A.C.E. Operator's manual - sm1200 & sm1600 consignes de sÉcuritÈ de l'utilisateur avertissement pour utiliser cet appareil en toute sécurité, il faut lire et coprendre tous les consignes de danger, d'avertissement et d'attention. Soyez attentif aux symboles que voici. Danger: ne pas respe...
Page -7- n.A.C.E. Operator's manual - sm1200 & sm1600 16. Ne remassez pas de objets qui brûient ou fument comme les cigarettes, les allumettes ou les cendres chaudes. 17. Les poulies de la courroie peuvent devenir chaudes pendant l'utilisation normale. Pour prévenir des brûlures, évitez de toucher l...
Page -8- n.A.C.E. Operator's manual - sm1200 & sm1600 instructions visant la mise a la terre preparation: consignes pour brancher l'appareil a la source d'energie et pour la mise à la terre. Cet appareil doit être mise à la terre afin d'eviter le risque de choc électrique. Cet appareil est pourvu d'...
Page -9- n.A.C.E. Operator's manual - sm1200 & sm1600 how to prepare the machine for operation assemble the handle attach upper (a) and lower (b) handle to handle socket (c) by aligning holes and securing with 2 part screws (d). See figure 1. Install the bag assembly position the bag coupling into t...
Page -10- n.A.C.E. Operator's manual - sm1200 & sm1600 maintenance this section describes the procedures that must be done by the operator. Warning: to prevent injury, always turn off the switch and remove the electrical plug from the electrical outlet before changing the brush, belt, or filter bag ...
Page -11- n.A.C.E. Operator's manual - sm1200 & sm1600 maintenance (cont.) 9. Place the rubber end cap covers over both end caps (flat side against end cap). Align holes and secure. Then, slant the brush roll forward so the end caps are in line with the slots in the cleaner base. Push the brush roll...
Page -12- n.A.C.E. Operator's manual - sm1200 & sm1600 steel core brush warning: turn off the switch and disconnect unit from electrical supply before replacing brush strips. 1. New brush strips inserts are supplied in sets. To replace, first disconnect the machine from the electrical outlet. 2. Rem...
Page -13- n.A.C.E. Operator's manual - sm1200 & sm1600 n.A.C.E. Sm1200 & sm1600 trouble shooting guide problem possible cause solution motor does not run. 1) not firmly plugged in. 1) check attachment plug. 2) bad on-off switch. 2) replace switch. 3) line open. 3) replace cord. 4) motor open. 4) che...
Page -14- n.A.C.E. Operator's manual - sm1200 & sm1600 base assembly drawing 3/04 n.A.C.E. Sm1200 & sm1600 113.
Page -15- n.A.C.E. Operator's manual - sm1200 & sm1600 ref. Part no. Description qty. 1 51229n hood and graphics, n.A.C.E. 1 2 80065a screw (m4 *10) 2 3 51949a cable clip 1 4 80066a screw (m4* 18.5) 6 5 washer (4.2 *12*1) 4 6 51348a motor assembly, 120v 1 7 51230a motor exhaust (lh) 1 8 30161a exhau...
Page -16- n.A.C.E. Operator's manual - sm1200 & sm1600 n.A.C.E. Sm1200 & sm1600 handle and filter bag assembly drawing 3/04 92 93 91 96 97 90 89 88 87 35 26 85 83 31 86 81 80 82 79 78 77 76 75 74 73 72 71 70
Page -17- n.A.C.E. Operator's manual - sm1200 & sm1600 ref. Part no. Description qty. 26 56489a screw (m4*15) 23 31 51211a e-clip (e6) 5 35 56485a screw (m4*8) 3 70 30138b handle grip 1 71 51240a handle assembly - upper chrome 1 72 30143a bag hook 1 73 30144a bag retainer 1 74 30142a cord retainer- ...
Page -18- n.A.C.E. Operator's manual - sm1200 & sm1600 nacecare solutions u.S. Limited warranty this n.A.C.E. Industrial/commercial product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated...
