1. DL manuals
  2. Nacecare
  3. Floor Machine
  4. TTB 516
  5. Owner's Instructions Manual

Nacecare TTB 516 Owner's Instructions Manual

Manual is about: TTB 516; TTB 1840

Summary of TTB 516

  • Page 1

    Original instructions warning! Read instructions before using the machine. Attention lisez la notice avant d’utiliser la machine. Owner instructions mode d’emploi ttb 516 (ttb 1840).

  • Page 2

    233969 / 01/13 (a20) 2 index machine overview control panel overview rating label / personal protective equipment / recycling safety precautions before continuing, please refer to quick set up guide on page 8 ! ! Quick set-up guide machine set-up fitting the brushes fitting the floor tool filling th...

  • Page 3: Machine Overview

    233969 / 01/13 (a20) 3 machine overview 1. Operator control panel ( see page 4 ) 2. On / off lever 3. Waste water tank 4. Clean water tank 5. Brush deck 6. Squeegee blades 7. Floor-tool retaining knobs 8. Clean-water on / off tap 9. Clean-water emptying cap 10. Rear moving wheels 11. Floor-tool vacu...

  • Page 4: Control Panel Overview

    233969 / 01/13 (a20) 4 control panel overview 1 2 3 4 7 on / off switch on / off lever for full easy to follow instructions oncontrol panel set up and use, see machine operationset-up page 14 5 6 water flow on / off button 8 9 hi / lo button vacuum indicator battery charge level indicator handle pos...

  • Page 5: About The Machine

    233969 / 01/13 (a20) 5 rating label safety critical component charging lead: 18awg x 3 core svt cable (black) battery charger: 100 - 240 volt (50-60 hz) ppe (personal protective equipment) that may be required for certain operations. Ear protection safety footwear head protection safety gloves dust/...

  • Page 6

    233969 / 01/13 (a20) 6 component interval inspect for charging lead daily scuffing, cracks, splits, conductors showing brushes daily bristle damage, wear, drive collar wear squeegee blade before each use wear, cracks, splits filters before each use clogging and debris retention tanks after each use ...

  • Page 7

    233969 / 01/13 (a20) 7 warning: only use brushes provided with the appliance or those specified in the instruction manual. The use of other brushes may impair safety. A full range of brushes and accessories are available for this product. Only use brushes or pads which are suitable for the correct o...

  • Page 8: Quick Set-Up Guide

    233969 / 01/13 (a20) 8 quick set-up guide please read before commencing any operation. After the removal of all the packaging, carefully open and check the contents. Ensure the batteries are charged before use. ! ! 1 2 using the handle position lever, move the handle into the upright position. (fig ...

  • Page 9: Machine Set-Up

    233969 / 01/13 (a20) 9 machine set-up always ensure that the battery is disconnected before making any adjustments ! ! Fitting the brushes featuring the nulock brush system. The brush is simply pushed and twisted to lock, making fitting and removal a simple process. Slide the brush / pad under the b...

  • Page 10: Machine Set-Up

    233969 / 01/13 (a20) 10 machine set-up the ttb 516 is equipped with a large 5 us gallons clean-water tank allowing large areas to be cleaning in a single fill. Filling the clean-water tank to fill the clean-water tank, remove the filler cap (fig 10). Fill using either a hose, bucket or a suitable co...

  • Page 11: Machine Set-Up

    233969 / 01/13 (a20) 11 machine set-up control of substances hazardous to health (coshh) for best results use a non-foaming type of chemical, dilute to the manufacturers specification. For further guidance on hazardous substances refer to health and safety instructions online. Visit http://www.Hse.G...

  • Page 12: Machine Set-Up

    233969 / 01/13 (a20) 12 machine set-up moving the machine caution when moving or lifting the ttb 516, follow the national safety guidelines on lifting. ! ! When the bottom tank (clean water) is full the machine can be tilted to a maximum of 45 0 (fig 17). When the top tank (waste water) is full the ...

  • Page 13: Machine Operation

    233969 / 01/13 (a20) 13 machine operation pre-scrub mode the ttb -516 has been designed to cope with a variety of floor types and different levels of soiling. On heavily soiled floors use a ‘double scrub’ technique. First pre-scrub the floor with the floor-tool in the raised position (fig 21), allow...

  • Page 14

    233969 / 01/13 (a20) 14 setting the cleaning controls to start: hold down either trigger and press the yellow start button once (fig 26). Whilst the brush motor is running press the tap on / off button for fluid control (fig 27a), the clean tank tap must be open. Ideally set the tap to 45 0 (fig 27)...

  • Page 15: Regular Maintenance

    233969 / 01/13 (a20) 15 regular maintenance always ensure that the battery is disconnected prior to any maintenance operation ! ! After use, empty waste-water tank using emptying hose and flush-out with clean water. A remove the two hoses to disconnect the separator from the machine (fig 28). Lift o...

  • Page 16: Regular Maintenance

    233969 / 01/13 (a20) 16 regular maintenance once the clean-water tank has been emptied, the tank can be removed. Firstly detach the water feed pipe from the tap, this can be done by pushing the red tap clip in whilst pulling off the pipe. (fig 35). Removing the clean water tank the black suction hos...

  • Page 17

    233969 / 01/13 (a20) 17 changing the floor-tool blades ! ! Always ensure that the battery is disconnected prior to any maintenance to change the floor-tool, firstly swing the floor-tool clear of the machine (fig 41). Undo the two floor-tool retaining knobs (fig 42). Unscrew the four knobs securing t...

  • Page 18: Battery Care

    233969 / 01/13 (a20) 18 battery care removing the battery unplug the battery from the machine using the red connection handle (fig 48). The battery can then be lifted from the machine for storage or charging (fig 49). Recharge the machine fully after its last use. Do not leave the machine in a disch...

  • Page 19: Machine Charging

    233969 / 01/13 (a20) 19 machine charging the ttb-516 come with its own stand-alone charger. Insert the charging lead required for your country into the charger. Connect the charger to a suitable power supply. The battery meter displays the charge level of the batteries; when fully charged, all meter...

  • Page 20: Trouble-Shooting

    233969 / 01/13 (a20) 20 trouble-shooting problem cause solution machine will not operate missing or blown fuses battery not connected low battery charge fit or replace fuse (page 8) connect battery (page 8) charge batteries (page 19/21) vacuum will not operate vacuum not turned on turn on vacuum (pa...

  • Page 21

    233969 / 01/13 (a20) 21 recommended spare parts - ttb-516 606260 ttb-516 battery pack (boxed) 606261 ttb-516 replacement blade set 606266 ttb-516 battery & charger pack (uk) 303985 ttb-516 filler cap assembly 606267 ttb-516 battery & charger pack (euro) 237268 filler cap lid 606268 ttb-516 battery &...

  • Page 22

    233969 / 01/13 (a20) 22 ttb-516 drw-7279 (a06) 06:08:2012.

  • Page 23

    233969 / 01/13 (a20) 23 notes .......................................................................... .......................................................................... ........................................................................... ...............................................

  • Page 24

    233969 / 01/13 (a20) this machine has been packed with the following charging lead + charger brush / pad battery pack floor tool signed.