- DL manuals
- NAD
- Stereo Receiver
- C 725BEE
- Owner's Manual
NAD C 725BEE Owner's Manual
Summary of C 725BEE
Page 1
En g li sh fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ ® owner’s manual c 725bee stereo receiver.
Page 2
Save these instructions for later use. Follow all warnings and instructions marked on the audio equipment. 1 read instructions - all the safety and operating instructions should be read before the product is operated. 2 retain instructions - the safety and operating instructions should be retained f...
Page 3
19 damage requiring service - unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) when the power-supply cord or plug is damaged. B) if liquid has been spilled, or objects have fallen into the product. C) if the product has be...
Page 4
Important information for uk customers donot cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. If, noneth...
Page 5
Introduction table of contents thank you for choosing nad. The c 725bee stereo receiver is a technologically advanced and highly capable product — yet we have invested great effort in making it simple and easy to use. We have been careful to ensure that the c 725bee is as musically transparent and s...
Page 6
Introduction getting started unpacking and setup what’s in the box packed with your c 725bee you will find: • the sr 8 remote control with 2 (two) aaa batteries • zr 5 zone remote control with 3v cr2025 battery • this owner’s manual save the packaging please save the box and all of the packaging in ...
Page 7
1 standby: with the rear panel power switch set to on position, press this button to switch on the c 725bee from standby mode. The standby led indicator will turn from amber to blue and illuminate the vfd. Pressing the [standby] button again turns the unit back to standby mode. The c 725bee can also...
Page 8
10 remote sensor: point the sr 8 remote control at the remote sensor and press the buttons. Do not expose the remote sensor of the c 725bee to a strong light source such as direct sunlight or illumination. If you do so, you may not be able to operate the c 725bee with the remote control. Distance: a...
Page 9
1 +12v trigger out: the +12v trigger out is used for controlling external equipment that is equipped with a +12v trigger input. This output will be 12v when the c 725bee is on and 0v when the unit is either off or in standby. This output can drive a load up to 150ma at 12v. 2 ir in/out: these mini-j...
Page 10
10 main in: connections to an external pre-amplifier or processor, such as a surround-sound decoder. In normal use, this should be connected to pre out sockets (no. 9) with the links supplied. To connect your nad c 725bee to external processor or pre-amplifier, remove first these links. Use a twin r...
Page 11
Using the sr 8 remote control the sr 8 remote control handset handles the key functions of the c 725bee as well as other nad stereo receivers, integrated amplifiers and preamplifiers. It has additional controls to remotely operate nad cd players, am/fm tuners and dedicated am/fm/dab tuners. It will ...
Page 12
8 vol [ ] : press [ ] button to increase or decrease the loudness level. Release the button when the desired level is reached. The vfd on the front panel will indicate the level set. For nad receivers, the vfd will also show “volume up” or “volume down” while pressing sr 8’s . The volume buttons do ...
Page 13
Using the zr 5 remote control the zr 5 remote control is a discrete compact remote for controlling the c 725bee from various rooms other than the main room. The zr 5 remote allows full separate control of the source selection irrespective of the main room. This means the zone input may be completely...
Page 14
The c 725bee’s internal am/fm tuner offers very high quality sound from radio broadcasts. The reception and sound quality will always be dependent to a degree however on the type of antenna(s) used as well as proximity to the broadcast origin, geography and weather conditions. About antennas the sup...
Page 15
Choosing tuner mode the front-panel [tuner mode] button is a dual-purpose control. In the normal position (“fm mute on” is briefly displayed in the lower line of the vfd; “fm stereo” and “fm mute” icons on the vfd are lit), only the stations with a strong signal can be listened to, and the noise bet...
Page 16
About dab radio (230v version only) until now, analogue radio signals such as fm or am have been subject to numerous kinds of interference on their way from the transmitter to your radio. These problems were caused by mountains, high-rise buildings and weather conditions. With digital audio broadcas...
Page 17
Station order use “station order” to sort the sequence of the listed stations. There are three orders – alphanumeric, ensemble and active. 1 while listening to a dab broadcast, press front panel’s [tuner mode] button and then [tune ] to select “station order”. Press [enter]. 2 toggle [tune ] to sele...
Page 18
Information settings while listening to a dab broadcast, the type of information displayed in the lower line of the vfd can be varied. Toggle front panel’s [info] button to step through the following display options: station name dls channel and frequency ensemble name program type time and date aud...
Page 19
The c 725bee is equipped with a data port in the rear panel where an optional “nad ipd 1 dock with ipod” (nad ipd 1) can be plugged in. With the nad ipd 1 linking the c 725bee with your own ipod player, you can enjoy listening to your favorite tracks and playlists. You can control your ipod player u...
Page 20
Condition possible causes possible solutions nopower. The power cord is disconnected. • plug the power cord into the wall outlet securely. • nosound. Power ac lead unplugged or power not switched on. • check ac lead. • mute on. • switch off mute. • nosoundonechannel. Balance control not centered. • ...
Page 21
Preamplifier section line level inputs (mp, cd, disc, aux, tape) input impedance (r and c) 22 kΩ + 100pf input sensitivity 250 mv (ref. Rated power) maximum input signal 6v signal / noise ratio a-weighted 1 95 db signal / noise ratio pre-amp out, a-weighted 107 db frequency response thd + noise, smp...
Page 22
Tuner section fm section tuning range 87.5 - 108.5 mhz (50 khz steps) usable sensitivity (98 mhz) 12 dbu signal/noise ratio (60 dbµ ihf-wtd mono) 65 db (60 dbµ ihf-wtd stereo) 60 db frequency response ±1.5 db (20 hz - 15 khz, 60 dbµ) channel separation (60 dbµ) 30 hz 30 db 1 khz 35 db 10 khz 30 db c...
Page 23
En g li sh fr anÇ ais esp aÑol it aliano deut sch nederl ands svensk a РУ ССКИЙ.
Page 24
Www .Nadelectronics .Com ©2008 nad electronics international a division of lenbrook industries limited all rights reserved. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of nad electronics international c 725bee owner’s manual issue 1...