NAD T737 Owner's Manual - page 11
USING THE AVR 3 REMOTE CONTROL
The AVR 3 remote control handset handles the key functions of the T 737 as well as other NAD Stereo
Receivers, Integrated Amplifiers and Preamplifiers. It has additional controls to remotely operate NAD CD
Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners. It will operate up to a distance of 23ft (7m).
Alkaline batteries are recommended for maximum operating life. Two AA batteries should be fitted in the
battery compartment at the rear of the Remote Control handset. When replacing batteries, check that they
have been put in the right way round, as indicated on the base of the battery compartment.
When a command from the remote control is received, the Standby LED indicator will blink. Note that
the indicator may also blink when receiving commands not necessarily for the T 737 but for other
components in the system. Please refer to previous sections of the manual for a full description of
individual functions.
NOTE
TheremotecontrolhandsetsuppliedwiththeT737isofauniversalNADtype,designedtooperate
severalNADmodels.SomebuttonsareapplicableonlytospecificNADmodels.Contactyourdealer
orNADaudiospecialistforassistance.
1 POWER ON & OFF: The AVR 3 remote has a separate ON and OFF button. Press the ON button
to switch the unit from Standby to operating mode. Press the OFF button to switch the unit to
Standby mode.
2 DEVICE SELECTOR: A Device Selector button determines only what component the AVR 3 will
command; it does not perform any function on the receiver. Press desired Device Selector button
for the applicable buttons to be directed to a “page” of commands relevant to the selected device.
Upon selecting a Device, you can now press the corresponding AVR 3 control buttons applicable
for the selected Device.
3 INPUT SELECTORS: Refer to the corresponding labels printed in the remote control faceplate
and their respective assigned buttons to make use of these functions. Set the DEVICE SELECTOR
to “AMP” in order to gain access to these buttons. The input selector buttons perform the same
functions as the buttons labeled the same on the front panel.
NOTE
INPUT1,INPUT2uptoINPUT6correspondtotheT737’sSOURCE1,SOURCE2uptoSOURCE6.
INPUT7correspondstoMULTI.Theseinputsorsourceswillhavetobeenabledforthemtobe
directlyrecalledoraccessed.
4 NUMERIC KEYS: The numeric keys allow for direct input of tracks for CD players and direct
channel/preset access for tuners and receivers.
5 A/V PSET: In combination with the numeric keys, press a Preset number from 1 to 5. Note that the
Preset settings can be configured via the A/V Presets menu.
6 DIMMER (for use with NAD Stereo Receiver, Tuner and CD Player): Reduce, turn off or restore
VFD brightness. Depending on the NAD model, the brightness of the front panel display will vary
when you toggle this button.
7 TEST: Press to initiate speaker TEST mode while at “Speaker Levels” line item under “Speaker Setup”
menu.
8 MUTE: Press the [MUTE] button to temporarily switch OFF the sound to the speakers and
headphones. MUTE mode is indicated by the Standby LED indicator flashing for NAD Integrated
Amplifiers or “Mute” shown in the VFD of NAD Receivers. Press MUTE again to restore sound or by
pressing [VOL
] of AVR 3.
9 SURR: Toggle to select desired listening or surround mode.
IDENTIFICATION OF CONTROLS
AVR 3 REMOTE CONTROL
2
9
10
11
1
3, 4
8
5
12
7
6
11
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ