1. DL manuals
  2. Nadatel
  3. DVR
  4. SDVR-16000C
  5. User Manual

Nadatel SDVR-16000C User Manual

Manual is about: Nadatel 9CH/16CH MPEG4 DVR User guide

Summary of SDVR-16000C

  • Page 1

    User guide 9ch/16ch mpeg4 digital video recorder ver. 2.1 about this user guide before installing and using this unit, please read this user guide carefully. Be sure to keep it handy for later reference . The specification and information are subject to change without notice for quality improvement..

  • Page 2: Safety Precautions

    Safety precautions 2 explanation of graphical symbols this symbol indicates the presence of important operating and maintenance (servicing) instruction in the literature accompanying the product. This symbol indicates the presence of un-protected ”dangerous voltage” within the product’s enclosure th...

  • Page 3: Warnings

    3 warnings installation and servicing should be performed only by qualified and experienced personnel. Power off the dvr when connecting cameras, audio or sensor cables. The manufacturer is not responsible for any damage caused by improper use of the product or failure to follow instructions for the...

  • Page 4: Rack Mount Instructions

    4 rack mount instructions the following or similar rack-mount instructions are included with the installation instructions: a) elevated operating ambient - if installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient...

  • Page 5: Product Components

    Product components the package contains the main unit and its components as specified below. When you purchase the unit, please check to ensure the components specified below are included. Dvr set cdrw (option) client software cd remote control battery1.5v (aaa x 2ea) user guide ide hdd cable 80pin ...

  • Page 6

    Power cord (110v or 220v) video signal select & rs-422/485 settings video mode video output ntsc pal bnc vga rs-422/485 select rs-485 termination 485 422 on off notice 1. Do not change the setting when the power is on. When the switch is changed, the dvr should be rebooted to apply the new setting. ...

  • Page 7: Compatible Hdd Models

    7 compatible hdd models company capacity rpm buffer interface 80 gb 7200 rpm 2 m e-ide 160 gb 7200 rpm 8 m e-ide 250 gb 7200 rpm 8 m e-ide hitachi 500 gb 7200 rpm 8 m e-ide 80 gb 7200 rpm 2 m e-ide 200 gb 7200 rpm 2 m e-ide 250 gb 7200 rpm 8 m e-ide maxtor 300 gb 7200 rpm 16 m e-ide 80 gb 7200 rpm 2...

  • Page 8: Cdrw Installation Guide

    Are different with others, the dvr could not recognize hdd. Cdrw installation guide 1. Open the top cover of dvr set and install the cdrw inside the dvr. 2. Fasten the screws on both side of cdrw as indicated in red circle below. 3. Connect the ide cdrw 40pin cable and power cable to the point on bo...

  • Page 9: Hdd Installation Guide

    Hdd installation guide 1. Unfasten the cover of the unit. 2. Fix the bracket to the hard disk using the supplied hdd mounting bracket screws. 3. Connect the supplied ide hdd 80pin cable and power cable to the hard disk and fix the hard disk to the unit the supplied hdd fixing screws. 9.

  • Page 10: Specifications

    4. Hdd jumper setting 1 st hdd = master 2 nd hdd = slave specifications item dvr-9ch/16ch channel, input level 9/16ch, composite 1.0vp-p, 75 ohm signal format ntsc/pal input video loss check yes main monitor output 1 ch bnc, 1 ch s-video, 1ch vga output level composite 1.0vp-p +_0.2, 75 ohm signal f...

  • Page 11

    11 704x480 352x288 704x288 pal 704x576 recording quality grade 5 grades recording mode continuous / schedule / motion/ sensor/ manual motion detection motion detection setup by grid pre & post recording yes display frame rate ( /sec) ntsc: 30fps/ch, 60 fields / pal: 25fps/ch, 50 fields multi-decodin...

  • Page 12: Table of Contents

    12 recording performances and resolutions per models model recoding performance (max.) ntsc 352x240: 120fps 704x240: 60fps 704x480: 30fps sdvr-9000c pal 352x288: 100fps 704x288: 50fps 704x576: 25fps ntsc 352x240: 240fps 704x240: 120fps 704x480: 60fps sdvr-9200c pal 352x288: 200fps 704x288: 100fps 70...

  • Page 13

    13 3-6. Setup – system mode .................................................................................................. 31 3-7. Setup – password mode ......................................................................................... 35 3-8. Setup – network mode ...........................

  • Page 14

    14 9-6. Pc system configuration .............................................................................................. 62 9-6-1. General...................................................................................................................... 62 9-6-2. Site .........................

  • Page 15

    15 1. Features ● 9/16 channels real-time live display and 9/16 channels simultaneous playback. ● mpeg-4 - unbeatable recording picture quality and compression ratio. Best format for minimizing recording space and bandwidth requirements for network transmission. ● triplex - simultaneous recording, pl...

  • Page 16

    2. Name, function and connection 2-1. Front panel the following information will help you to operate the front panel controls. Figure 2.1.1. Front panel table2.1.1. Indication lamps no. Name description a hdd indicating that the system is accessing the hard disk. B record indicating that the system ...

  • Page 17

    17 single- highlighted channel only. Mix- all of 4 channels. 8 f/rew jump/step backward. In playback mode, the playback position moves 60 seconds backward. 9 alarm press to enable/disable alarm operation. 9 f/adv jump/step forward. In playback mode, the playback position moves 60 seconds forward. 10...

  • Page 18

    2-2. Rear panel figure 2.2.1. Rear panel table 2.2.1. Rear panel connections no connection purpose 1 video in 9/16 connectors for video input. (ntsc/pal) 2 video out 9/16 connectors for video output. (loop back) 3 spot composite video output for spot monitoring. 4 video composite video output in nts...

  • Page 19

    2-3 remote controller power power on/off display display of full, quad or 9 split view f/rew jump 60 seconds backward play play/pause f/adv jump 60 seconds forward freeze/cap freeze/capture ff fast forward alarm disable alarm operation setup setup menu screen archive display archive list audio disab...

  • Page 20

    20 3. Setting up the dvr the following sections detail the initial setup of the dvr 3-1. Setup – main screen when the setup button is pressed, the dvr will ask for a password. The default password is 1111, which can be entered by pressing the up button 4 times and then pressing the sel button. It is...

  • Page 21

    3.1.1. Will appear. Navigate through the menu items and press the sel button to enter the sub- category menu. Figure 3.1.1. Setup screen table 3.1.1. Setup menu configuration display osd sequence seq-dwell time osd contrast channel display, brightness, contrast, hue, saturation record resolution cha...

  • Page 22

    System dvr-id description language date format set date & time send email password admin password user password network password network port client access bandwidth saving network type ip, gateway, subnet mask, dns ddns config save config load config load default load factory default 3-2. Setup – d...

  • Page 23

    Table 3.2.1. Menu items in display mode setup item description osd enable/disable on-screen-display. Sequence enable/disable sequential display of video in full screen mode. Seq-dwell time set the dwell time for each, 4 or 9 channels display in sequential display mode. Osd contrast set the visibilit...

  • Page 24

    24 table 3.3.1. Menu items in recording mode setup menu item description resolution set the resolution to either 704x480, 704x240, or 352x240 for ntsc. (pal: 704*576/ 704*288/ 352*288) channel select the channel to apply the following settings on. Changes you make will immediately take effect with t...

  • Page 25

    3-3-1. Quick record setting user can setup all the values related with record such as frame rate, quality, recording type, pre-recording, and post-recording on one page of setup screen. 1. Go to record>channel and press sel button. 2. Then the bellow setup screen will pop up. Figure 3.3.2. Quick rec...

  • Page 27

    Table 3.4.1. Menu items in device setup screen item description alarm out set the sensor, motion, and video loss for each alarm. Spot-out set the all details for spot monitoring. Ptz set the ptz camera speed, number, type and id. Channel select specified channel for motion zone setup. Motion zone se...

  • Page 28

    Alarm out select alarm from 1 to 4. Sensor in enable setting up to 4 sensors of 9/16 sensors for the each alarm. Motion on enable setting up to 4 cameras of 9/16cameras for the each alarm. Video loss on enable setting up to 4 cameras of 9/16 cameras for the alarm. Alarm duration set the dwell time o...

  • Page 29

    Figure 3.4.4. Ptz control setup screen note: for speed dome cameras that support rs-485, connect them directly to the rs-485 port. If the camera is controlled with rs-232c, use an rs-485 to rs-232c signal converter. On the ptz control setup screen, you can select or set the protocol type of the came...

  • Page 30

    Figure 3.4.5. Motion zone selection screen 3-5. Setup – storage mode set the storage parameters in the storage setup screen. Figure 3.5.1. Storage setup screen table 3.5.1. Menu items in storage setup screen item description 30

  • Page 31

    Overwrite when enabled, the dvr will continue recording and overwrite the oldest existing recorded data once the hard drive is full. When disabled, recording will stop once the hard drive is full. Disk format format the hard drive. Use the up and down arrow buttons to select on, then press sel. You ...

  • Page 32

    Item description dvr id set the name of the dvr. Press the sel button, use the left and right or up and down arrow controls to navigate through the position for each alphanumeric character and press sel to apply the selected character. And press ok to confirm the name. Space / caps lock(select eithe...

  • Page 33

    Date & time set the present date and time for the dvr. Press sel, then use the left and right arrow controls to navigate through the position of each alphanumeric character in the date and time. Use the up and down arrow controls to change the selected character. Press esc and select yes to confirm ...

  • Page 34

    3. Others - begin (mar/1 st /sun/00h) - end (sep/1 st /mon/00h) (set the begin and end time for the specific area except eu and usa) use the up and down arrow controls to change the value of month, week, day and hour. Caution: -do not set the start time to 23:00 for dls. -dls can’t be applied, if th...

  • Page 35

    3-7. Setup – password mode use the left or right and up and down arrow controls to set the password. Figure 3.7.1. Password setup screen table 3.7.1. Menu items in passwrord setup screen item description admin password set the administrator password. After selecting this menu item you will be promot...

  • Page 36

    36 down=3 left=4 admin password is asked for the following functions. Setup, power, search, and key lock from remote control. User password set the user password. After selecting this menu item you will be promoted for your current password and then the new password. Follow the prompts to change and...

  • Page 37

    3-8. Setup – network mode set up your network parameters on the network setup screen. Figure 3.8.1. Network setup screen table 3.8.1. Menu items in network setup screen item description port port number (default: 5445) client access enable/disable remote access through client software. Bandwidth sav...

  • Page 38

    The ddns sever name is ns.Standalone4ch.Com. Caution: do not change this sever name. If this is changed, the ddns service cannot be used. Registration check the mac address of dvr from setup>system>description. Please contact a distributor or an installer to register your dvr on a ddns server. Regis...

  • Page 39

    3-8-2. Network types 3-8-2-1. Lan 1. For the use of fixed ip. (see your network administrator if you do not have this information.) 2. When dvr is installed in ip sharer that is connected with adsl, a user can assign fixed ip to dvr from ip sharer itself using “dmz” function out of such sharer. Inpu...

  • Page 40

    Dns the address for the dns server 3-8-2-2. Dhcp an ip address is automatically assigned by the dhcp server, which automatically assigns ip address and other parameters to new devices. When adsl or other network being used adopts variable ip method, not fixed ip. This option is used as a way to auto...

  • Page 41

    Id the user id for the adsl connection password the password for the adsl connection 3-8-3. Saving setup of network setup after changing the network configuration, confirmation window will popup. To preserve the setup values that you have selected, select yes. Then system will reboot. Figure 3.8.5. ...

  • Page 42

    The saving process. Load config user can upload the configuration of dvr to another dvr using the usb memory stick. Put the usb stick on the front panel and press sel to start the loading process. Load default select on to reset the system to the default settings. (password, date format, dls, networ...

  • Page 43

    Load factory default select on to reset the system to the factory default settings. 4. Saving setup to preserve the setup values that you have selected, select yes. Figure 4.1.1. Save setup screen 43.

  • Page 44

    5. Live, search, and playback 5-1. Live viewing screen in the live screen, video inputs from the cameras are displayed as they are configured in the display setup screen. Various on-screen display (osd) symbols, which indicate the status of the dvr, are described in table 5.1.1. Figure 5.1.1. Live v...

  • Page 45

    Alarm indicator. When there is an alarm (sensor or motion alarm) in the video channel, this icon will be highlighted bright red. Indicates that a network client is connected to the dvr. Indicates that sequencing mode is enabled. Table 5.1.2. Button functions in live viewing screen button description...

  • Page 46

    To exit from each menu. 5-2. Search screen press search in live mode to enter the search screen. When you press the search button, dvr asks for a password as in figure 5-2-1. Figure 5.2.1. Search screen enter the password using the arrow controls. There are 7 ways of search menu such as timeline, ev...

  • Page 47

    C: continuous-green m: motion-yellow s: sensor-red r: manual -purple 4. Once you have selected the time zone, press the sel button to move to the 60 minutes time table. 5. Select all or a specific channel to search by using the up and down arrow buttons. 6. Once you select the channel, use the left ...

  • Page 48

    After the current selection. 9. Once the desired event has been selected, press sel to start playing back the selected video. 10. Press the backup button to launch the archiving function in playback mode. 5-2-3. Go to first time you can access the oldest recorded data on the dvr hard drive by select...

  • Page 49

    Figure 5.2.5. Log search screen 5-2-7. Archive search the archive search window is used to find previously stored video or images. 1. Select the date to begin searching by using the left, right, up and down buttons to navigate through the days. 2. Once you have selected the date, press sel to open t...

  • Page 50

    Figure 5.3.1. Play mode screen table 5.3.1. Button functions in play mode button description return to the previous menu screen, search window, or exit from the menu press to rewind the footage at 1x, 2x, 4x, and 8x speeds. Reverse playback speed is shown as -1x(normal), -2x (2 times normal), -4x (4...

  • Page 51

    Select the item you wish to control the ptz camera and control them by using the up and down or left and right buttons. Please refer to the table 6.1.1. For the control. Figure 6.1.1. Ptz control screen table 6.1.1. Button functions in ptz control item description pan / tilt use the up or down butto...

  • Page 52

    2. And the dvr will ask which media you will take for archiving. 3. Once you select the media, the system will start to archive the data to the selected media. Figure 7.1.1. Still image archiving and backup screen 7-2. Video backup onto usb flash memory or cd media video can be captured and archived...

  • Page 53

    Figure 7.2.1. Video archiving and backup screen the dvr will convert the corresponding portion of the video into an avi file. 7-3. Transferring still images or video from the archive list the stored data onto hard drive will be found in the archive list in search menu. User can back up still images ...

  • Page 54

    54 7-4-2. Playback of backup video in exclusive (nafs) format if the data is backed up in an exclusive file format, this video can be playbacked only an exclusive player in cd that is provided with dvr..

  • Page 55

    8. Upgrading firmware in order to upgrade, the firmware upgrade file must first be downloaded and copied into the usb memory stick. Create a new folder in the usb memory stick and name it “upgrade”. Copy the firmware upgrade file “app16xxxxxx.Bin” for 16ch dvr or “app9xxxxxx.Bin” for 9ch dvr into th...

  • Page 56

    9. Network – by an exclusive viewer the dvr provides a live remote monitoring feature. Remote monitoring requires installation of a software client program on your pc. Notice in a high bandwidth network, a maximum of four users can access one dvr simultaneously. In a low bandwidth network it is reco...

  • Page 57

    9-2. Minimum pc requirements pc specification minimum requirement recommended cpu intel pentium Ⅲ intel pentium Ⅳ 500mhz 2ghz memory 128mb 256mb vga 16mb 64mb resolution 1024x768 1024x768 disk space 10mb 10mb os windows 2000 windows 2000, professional, xp vista network 10/100base t 10/100base t othe...

  • Page 58

    9-4. Live viewer when installation is complete, double click the icon on your desktop to start the program. Figure 9.4.1. Main user interface table 9.4.1. Main controls in live no button description 1 date & time displays the current date and time. 2 connect click this icon to connect to the dvr 3 s...

  • Page 59

    4 lock/ unlock click this icon to lock/unlock all operations of the client software. Once the lock or unlock icon is clicked, this pop up window appears. Remember the password and enter it when you operate the client software. 5 pan/tilt use these buttons to control the pan/tilt features on the remo...

  • Page 60

    9-5. Search and playback viewer the search window can be accessed by clicking the search icon on the upper right of the main user interface. Figure 9.5.1. Main user interface table 9.5.1. Main controls in search no button description 1 date & time displays the recording time of the data selected on ...

  • Page 61

    3 capture click this icon to capture a still image of recorded video. Once the capture icon is clicked, this pop up window appears. The still image is captured in either jpeg or bmp file format. 4 mark in click this icon to set the start time for video backup. 5 mark out click this icon to set the e...

  • Page 62

    9-6. Pc system configuration click the setup icon to setup the configuration of pc that the network client s/w is installed. 9-6-1. General once you click the setup icon, this pop up window appears. Select security options and set a password. When you access any of the selected functions, you will n...

  • Page 63

    9-6-3. Event you can set event items, the amount of local disk space you want to allow and the save path for the log file. Z log – select to save event log into ‘log file’. Z icon – select to display the event on live video. Z event list – select to show the event in the ‘event list” window of live ...

  • Page 64

    9-6-4. Record you can set the recording conditions for always, event, or auto recording. You can also select individual channels or all channels to record. When you set the recording condition to event, you can set event for motion or alarm with duration. You can also set each or all channels to rec...

  • Page 65

    9-6-5. Disk you can select which local disk to use and the amount of disk space you want to allow the program to use for recording. You can also choose to overwrite data or stop recording when the maximum amount of disk space is full. 65.

  • Page 66

    10. Network – by an web-browser viewer the dvr provides a live remote monitoring feature by web-browser viewer. 10-1. Download web brower viewer and connection 1. User needs to access http://ns.Standalone4ch.Com/webview2/ to get a web browser viewer. Then the window will appear as bellow. Click “yes...

  • Page 67

    3. Click button and enter ip address (or domain name using ddns), the password, and port number. 4. Then user can access dvr. 10-2. Main features 10-2-1. Live figure 10.2.1. Main user interface - live 67.

  • Page 68

    Table 10.2.1. Main controls in live no name description 1 date & time displays the current date and time. 2 connect click this icon to connect to the dvr 3 search click this icon to search for recorded video. 4 live display mode click these icons to select display mode. 5 pause click this icon to pa...

  • Page 69

    No name description 1 date & time displays the current date and time. 2 connect/disconnect click this icon to connect to the dvr 3 live click this icon to search for recorded video. 4 display mode click these icons to select display mode. 5 backup click this icon to pause the display screen. 6 captu...

  • Page 70

    Lan: select when dvr is installed in local area network with router or ip sharer and ip address is static and private ip address. Adsl (pppoe): to use this adsl (pppoe) function when the network type connecting the dvr is using pppoe method. If adsl type is not using inputting ip and password like v...

  • Page 71

    Enter your e-mail address correctly. B. Press registration and register dvr as bellows, input mac address and registration that you checked from the rear of dvr. And input domain name and press [check] to see if domain name is usable or not. Notice id and password of registration ddns is not the sam...

  • Page 72

    2. Network access using domain name if ddns registration is successful, you can access your dvr via the provided network client s/w. A. Run network client s/w program and click the “connect” button. B. Enter your domain name instead of ip address in the “ip address” field. C. Enter the port no, prot...