Nady Audio 4180 Owner's Manual - Specifications
7
SPECIFICATIONS
(24)
(25)
(26)
(27)
REAR PANEL CONTROLS & CONNECTIONS
REAR PANEL
(24) POWER
SWITCH
Turns the unit ON or
OFF. Always turn
level controls down
before turning on the
unit.
(25) VOLTAGE
SELECTOR SWITCH
For selecting the
proper voltage (115/
230VAC) to match the
power supply in your
area.
Note: To avoid
damage to your unit,
always make sure this
switch is set to the
correct supply
voltage. Damage
caused by improper
use is not covered by
the warranty.
SPEAKERS
Impedance ........................................................................ 8 Ohms
Tweeter type ............................................................. Piezoelectric
Woofer diameter ......................................................................... 8"
PA-4180 MIXER SECTION
Power ........................................... 90W RMS @ 4 Ohms Per Side
S/N Ratio ........................................................................... >115dB
THD Power output, 20Hz to 20KHz .................................... <0.1%
CROSSTALK (1KHz @ 0dBu, channel in to master output)
Channel fader down ........................................................... <-60dB
FREQUENCY RESPONSE
(Mic input to output)
Line level o/p @ +4dBu into 600 Ohms ............................ +0/-3dB
Power amp o/p 1 watt into 8 Ohms per side ..................... +0/-3dB
SENSITIVITY @ LINE OUTPUT +4dBu with Master
and Channels controls set to MID
Mic/Line .......................................................................... -54/-24dB
Tape in .................................................................................... -6dB
Max Input Level XLR ............................................................. -9dB
Max Input Level 1/4" .......................................................... +22dB
(26) POWER CONNECTOR WITH FUSE HOLDER
This standard IEC power cord receptacle is used to
connect the AC power to your unit. It features a built-in fuse
holder for a 5X20mm, (4A/250V for 115VAC, and 2A/250V
for 230VAC operation) fast-blow fuse. If the fuse
continuously blows, shut off the unit and have it serviced by
qualified service personnel.
(27) SPEAKER OUTPUTS
Two 1/4" (6.3mm) jacks, each powered by its own separate
amplifier output stage, for connecting left and right speaker
cabinets. The connected speaker impedance must be 4
ohms or greater. The PA-4180 delivers 90W RMS of power
@ 4 Ohms per each speaker output.
CAUTION: Do not overload the ENSEMBLE PA 4180 with
speaker loads less than 4 ohms as this will degrade
performance and may harm the unit. Damage caused by
improper use is not covered by the warranty.
CHANNEL EQUALIZATION
Low EQ ...................................................................... 90Hz
±15dB
Mid EQ ................................................................... 2.5KHz
±15dB
Hi EQ ....................................................................... 12KHz
±15dB
MASTER EQUALIZATION
Low EQ ...................................................................... 90Hz
±15dB
Mid EQ ................................................................... 2.5KHz
±15dB
Hi EQ ....................................................................... 12KHz
±15dB
Microphone Preamp E.I.N.
(150ohm Terminated, max. Gain) ................................... -102 dBm
Power requirements ................. 100-120, 220-240 VAC, 50-60 Hz
Fusing ........................................................... 5x20mm glass type,
4A/250V for 115VAC, and 2A/250V
for 230VAC operation, fast-blow fuse
Dimensions (W x H x D) ................................ 15.5" x 27.5" x 10.5"
(40 cm x 70 cm x 27 cm)
Weight ............................................................ 62.7 lbs. (28.4 Kgs)
Note: Specifications subject to change without notice for
product improvement purposes.