Summary of TUNERS
Page 1
O w n e r s m a n u a l t u n e r s.
Page 2: 1.0 Equipment Installation
Page 1.0 equipment installation normally your naim equipment will have been installed by the dealer who sold it to you even if you live outside their immediate vicinity. Your dealer is responsible for making sure that the system sounds exactly as it should and information given here is not intended ...
Page 3: 2.0 Getting Started
2.0 getting started 2.1 switching on and off source components and power supplies for cd players, tuners, preamplifiers and crossovers should be switched on before switching on the amplifier(s). Always switch the amplifier(s) off and wait about a minute for its power supply capacitors to discharge b...
Page 4: 3.0 Warnings
Important in order to comply with current european safety regulations it is essential that the naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. Do not under any circumstances allow anyone to modify your naim equipment without first checking with the factory, your deale...
Page 5: 4.0 Connection
4.0 connection 4.1 mains lead as the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: the wire which is coloured green-and-yellow must be connected to the terminal in the plug which is ma...
Page 6: Nat 01 and Nat 02 Operation
5 nat 01 and nat 02 operation connections the fm aerial input socket must be connected via 75ohm low-loss coaxial cable to a suitable roof- mounted directional aerial. Aerial requirements the tuner aerial should be mounted on the roof, clear of obstructions and also as high as possible. Horizontally...
Page 7: Nat 01
6 nat 01 front nat 01 rear connected to napst power supply napst power supply mains input to preamplifier 75 ohm fm aerial cable direction marker 5 pin din 5 pin din (snaic) interconnect cables ch1 nc nc -ve ch 2 nat 01 output signal stereo.
Page 8: Nat 02
7 nat 02 front nat 02 rear to preamplifier power switch mains lead 75 ohm fm aerial ch1 nc nc -ve ch 2 nat 02 output specifications nat 01 and nat 02 tuning range vhf/fm 87.5 - 108mhz output level 01 400mv per channel at 100% modulation 02 340mv per channel at 100% modulation mains supply 100 v, 115...
Page 9: Nat 05 Operation
8 nat 05 operation connections the fm aerial input socket must be connected via 75ohm low-loss coaxial cable to a suitable roof- mounted directional aerial. Aerial requirements the tuner aerial should be mounted on the roof, clear of obstructions and also as high as possible. Horizontally polarised ...
Page 10: Specifications
9 to preamplifier mains input power stereo freq scan preset • • • • down up mode mono note the rc5 input is designed to accept external control signals for multi-room applications. Contact your dealer for further information on its use. The nat 05 features various technologies to reduce microphonic ...
Page 11: Narcom 2 Remote Handset
Narcom 2 remote handset narcom 2 is a multi-functional remote control handset designed to be used with naim audio cd players, integrated amplifiers, pre-amplifiers and preset tuners. The handset control configuration is based around three types of keys: system component keys, global keys and soft ke...
Page 12
3 soft keys these keys operate functions depending on the system component key setting. Numeric keypad: in preamp mode the numeric keys will switch between the amplifier inputs (1 - cd, 2 - tuner, 3 - tape, 4 - av, 5 - aux 1, 6 - aux 2). In cd mode the numeric keys will select tracks. In tuner mode ...
Page 13: Appropriate Standards
1 2 naim audio southampton road salisbury england sp1 2ln tel: 01722 332266 www.Naim-audio.Com owntu • issue 3 • may 2001 ec declaration of conformity to appropriate standards manufacturer naim audio limited southampton road salisbury england sp1 2ln products nat 01, nat 02, nat 05 tuners napst powe...