- DL manuals
- NAMCO
- Game Console
- 90500135
- Operator's Manual
NAMCO 90500135 Operator's Manual
Summary of 90500135
Page 1
Operators manual i t is the responsibility of the operator to maintain customer safety at all times , and it is imperative that the details set out in this manual are followed precisely part no. 90500135 issue 1 bee panic.
Page 2: Contents
Page 2 contents operators manual ................................................................................................................1 general safety considerations ..................................................................................... 4 allgemeine sicherheitshinweise .......
Page 3
Page 3 8. Maintenance ...................................................................................................................53 8-1 general cleaning ...........................................................................................................55 8-1-1 cleaning the hood ........
Page 4
Page 4 no part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without permission from namco europe limited. While the i...
Page 5
Page 5 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more removing and replacing parts l l l l l adjustments or maintenance on this equipment should be carried out by suitably qualified personnel only. L l l l l do not make any alteration t...
Page 6
Page 6 dieses dokument darf in keiner weise vervielfältigt werden. Jegliche tonaufnahmen sowie die speicherung auf datenträger (suchsysteme), die weitergabe oder sonstiges kopieren für den gewerblichen und privaten gebrauch sind untersagt und bedürfen der vorherigen genehmigung durch namco europe li...
Page 7
Page 7 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more hinweise zur aufstellung l l l l l niemals das gerät einschalten bevor die aufstellung völlig abgeschlossen ist. L l l l l zur vermeidung von elektroschlägen muß das gerät mit einem ...
Page 8
Page 8 denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra namco europe limited...
Page 9
Page 9 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more punkter om installation l l l l l tænd aldrig for strømmen til maskinen før installering er fuldført. L l l l l for at undgå mulige elektriske stød sikres, at maskinen er forbundet t...
Page 10
Page 10 no se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para uso público o privado, sin permiso de namco europe limited. Si bien la i...
Page 11
Page 11 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more retirar y reemplazar partes y unidades . L l l l l las revisiones de instalación, los ajustes, y el mantenimiento rutinario deberán llevarse a cabo sólo por personal cualificado. L ...
Page 12
Page 12 aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d’enregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique...
Page 13
Page 13 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more notes d’installation l l l l l ne jamais mettre le jeu en marche avant que l’installation ne soit complétement effectuée. L l l l l afin de prévenir une éventuelle électrocution, s’...
Page 14
Page 14 Κανένα μέρος αυτής της έκδοσης δεν μπορεί να αναπαραχθεί με οποιοδήποτε μηχανικ" ,φωτογραφικ" ή ηλεκτρονικ" μέσο , ή με μορφή φωνητικής ηχογράφησης και ούτε να αποθηκευτεί με επανορθωτικ" σύστημα , να μεταδοθεί ή να αντιγραφεί για δημ"σια ή ιδιωτική χρήση , χωρίς την άδεια της namco europe l...
Page 15
Page 15 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more ΑΠΟΜΑΚΡΥΝΣΗ ΚΑΙ ΑΝΤΙΚΑΤΑΣΤΑΣΗ ΜΕΡΩΝ - ΑΝΤΑΛΛΑΚΤΙΚΩΝ l l l l l Εγκατ%σταση , μετατροπ# # λεγχος ρουτνας μπορε να γνεται μνο απ εξουσιοδοτημνα %τομα . L l l l l Δεν πρπει να γνονται μ...
Page 16
Page 16 nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza l’autorizzazi...
Page 17
Page 17 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more notes d’installation l l l l l non accendere mai la macchina finchè l’installazione non è stata completata. L l l l l allo scopo di prevenire possibili scosse elettriche, la macchin...
Page 18
Page 18 ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra namco europe limited. Da in...
Page 19
Page 19 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more fjerne og utskifte enheter og deler. L l l l l installasjon, service, justering eller rutine vedlikehold skal bare utføres av kvalifiserte personer. L l l l l ikke lag noen forandri...
Page 20
Page 20 niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toest...
Page 21
Page 21 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more verwijderen en vervangen van assemblies en onderdelen l l l l l installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame persone...
Page 22
Page 22 nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos transmissiveis ou de outra forma copiados para uso publico ou privado sem a...
Page 23
Page 23 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more l l l l l esta maquina está equipada com rodas afim de facilitar a sua deslocação tenha cuidado ao mover a maquina num plano inclinado. L l l l l a altura total do bloco principal, ...
Page 24
Page 24 ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för offentlig eller privat användning, utan tillstånd från namco europe limi...
Page 25
Page 25 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more att beakta vid installation l l l l l sätt aldrig på strömmen på maskinen innan installationen är klar. L l l l l för att förhindra elektriska chocker, försäkra dig om att maskinen ...
Page 26
Page 26 tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman namco europe limited :in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. Namco europe limited:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite...
Page 27
Page 27 pathway play zone 50cm or more 50cm or more 1m90cm or more 1m or more 2m45cm or more 50cm or more 50cm or more asennushuomioita l l l l l Älä koskaan kytke laitetta päälle ennen kuin asennus on suoritettu loppuun. L l l l l tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maado...
Page 28
Page 28 1. Specifications power supply:- 230v / 400watts ac ambient operating +5°c to +25°c temperature coin acceptor:- mars cashflow - 1 channel dimensions:- assembled 900(w) x 1590(d) x 2240(h) lower cabinet 800(w) x 1520(d) x 970(h) upper cabinet 900(w) x 440(d) x 1100(h) weight assembled 140kg l...
Page 29
Page 29 2. Main components hood each prize sensor consists of two units installed opposite to each other prize sensor 1 prize sensor 2 prize sensor 5 prize sensor 4 prize sensor 3 7 -segment score displays target assy 1 target assy 4 target assy 6 target assy 8 target assy 9 target assy 7 target ass...
Page 30
Page 30 3. How to play n this is a gun shooting prize dispensing game. A player uses the gun to battle with ten bees. Each time the player shoots a bee in the display panel, the points indicated below that bee are added to the player’s score. The game can dispense two types or normal prize and one t...
Page 31
Page 31 4. Moving the machine l this equipment is fitted with castors to make it easier to move. Take care when moving the equipment on an inclined floor. L the overall height of this equipment is 2240mm. Take care of any overhead obstructions. (e.G. Light fittings, electric cables etc.) 4-1 separat...
Page 32
Page 32 4. Slowly tilt the upper cabinet backwards, while supporting the edge of the upper cabinet on the lower cabinet. 5. When the upper cabinet is level, remove the upper cabinet. Upper cabinet assy upper cabinet assy lower cabinet assy.
Page 33
Page 33 dieses gerÄt ist nur fÜr die gewerbliche aufstellung in geschlossenen rÄumen bestimmt. Das gerÄt darf an folgenden plÄtzen nicht aufgestellt werden 1. Im freien. 2. In direktem sonnenschein, an extrem feuchten und staubigen plätzen, an plätzen mit wasseranschlüssen und möglichen leckagen, na...
Page 34
Page 34 ও denne maskinen er bare konstruert for innendØrs bruk ikke installer maskinen pÅ fØlgende plasser. 1. Utendørs 2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje, nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur. 3....
Page 35
Page 35 esta maquina foi concebida para utilizaÇÃo em espacos interiores apenas nÃo instalar a maquinas nos seguintes locais:- 1. Exteriores. 2. `luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de água perto de ar condicionados ou equipamentos calorificos e locais ...
Page 36
Page 36 l l l l l warning • never turn the power to the machine on until installation has been completed. L l l l l warning • in order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug. L l l l l warning • so that customers...
Page 37
Page 37 5-3 assembling the backboard assemble the logo panel by following the diagrams below. 1 backboard 2 3 4 double-sided adhesive tape.
Page 38
Page 38 5-4 assembling the logo panel 5-5 attaching the logo panel and backboard logo panel 3 2 1 stick here backboard logo panel signboard assy upper cabinet assy.
Page 39
Page 39 6. Prizes after pushing a prize item forward, the prize dispensing sensors check whether the prize item has been dispensed at the prize outlet, so prizes can be hung on the payout assemblies at intervals to suit the prizes. To prevent two or more prizes being dispensed due to a prize dispens...
Page 40
Page 40 special prize items (for the right handed payout assembly viewed from the front.) weight: 300g or less per item each payout assembly can hold prize items totalling 3kg in weight. Size: maximum: 200mm(l) x 200mm(w) x 200mm(h) minimum: 10mm(l) x 50mm(w) x 50mm(h) 200mm 200mm 250mm 50mm 10mm 50...
Page 41
Page 41 6-2 preparing prize items the game uses prizes with hanging strings. When using prizes without strings, use a nylon string as a loop to hang prizes. The string length and dimension of each prize, including the string, must be as specified below. String length 30 to 50mm or more height of pri...
Page 42
Page 42 2. Hang the prizes on each payout assembly. 3. Close and lock the cover. Do not squeeze prize items too closely on the payout assemblies. Space prize items to prevent them from pushing each other. If the hanging interval of prizes is large, and the prize has not been dispensed within the set...
Page 43
Page 43 7. Adjustments adjustment or maintenance on this machine should be carried out by qualified personnel only. 쮕 쮕 쮕 쮕 쮕 einstellungen und wartung des gerätes dürfen nur von dafür qualifiziertem fachpersonal vorgenommen werden. Justeringer eller vedligehold af denne maskine bør kun udføres af k...
Page 44
Page 44 7-1 adjustment switches the adjustment switches are located inside the coin door. 1. Service switch. Press this switch to obtain game credits without incrementing the play meter. 2. Test switch slide the test switch on to enter test mode. Test mode allows testing and the changing of game set...
Page 45
Page 45 7-2 test mode 1. Open the coin door and slide the test switch “on”. 2. The 7-segment display indicates the name of the current test. Each time the select switch is pressed the test steps through in the following order. (1) output test (2) input test ( i ccccc ) (3) dispensing operation count...
Page 46
Page 46 7-2-2 input test when this test is selected, the following switches and sensors can be checked. To discontinue this test and step to the next test press the select switch. • each time a credit signal is sent from the cashflow, a sound is produced and the number shown on the 7-segment display...
Page 47
Page 47 7-2-5 payout motor test this test allows the checking of the payout motors and payout sensors. To discontinue this test and step to the next test press the select switch. • while this test is selected, the selection switches 1 and 2 and the challenge switch are illuminated. • press one of th...
Page 48
Page 48 7-3 using the setting modes 1. Open the coin door and slide the test switch “on” while pressing the select switch. 2. The 7-segment display indicates the name of the current adjustment mode. Each time the select switch is pressed the test steps through in the following order. (1) game price ...
Page 49
Page 49 7-3-1 game price setting this item sets the number of credit signals from the cashflow required for 1 game. Use select switch 1 or 2 to change the setting value. When in free game mode, a free game can be started by pulling the trigger of the gun during the attract mode. 7-3-2 play time sett...
Page 50
Page 50 7-3-4 continued game play time setting this item sets the number of plays provided for 1 continued game. Use select switch 1 or 2 to change the setting value. 7-3-5 normal stage difficulty setting this item sets the difficulty level of the normal stage game. The lower the difficulty level is...
Page 51
Page 51 7-3-7 attract sound setting this item sets the sound on or off during the attract mode. Use select switch 1 or 2 to change the setting value. 7-3-8 no prize item error setting this item sets the number of prize forwarding operations of the prize dispense motor that can occur, without detecti...
Page 52
Page 52 7-3-10 payout assy error setting this setting disables the use of payout assy 1 or 2. If a payout assy malfunctions, disabling a payout assy allows temporary operation of the game. The prize items on the disabled payout assy cannot be selected. Ensure that any faulty payout assy is replaced ...
Page 53
Page 53 8. Maintenance adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the power to the machine is turned off before commencing any maintenance work. (trouble shooting, service or repairs etc.) 쮕 쮕 쮕 쮕 쮕 einstellungen und wartung des gerätes d...
Page 54
Page 54 aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine uitgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.) afinações ou manutenção nesta maquina, deverão ser efectuadas sóme...
Page 55
Page 55 8-1 general cleaning 8-1-1 cleaning the hood never use any organic solvents, as solvents may cause irreparable damage. 1. Clean both the inside and outside of the hood using a cloth dampened with water or mild detergent. 2. Wipe with a dry cloth to remove any detergent or water from the surf...
Page 56
Page 56 8-1-4 cleaning the fibre optic cable l l l l l the xenon assy will remain hot and have areas of high voltage even though the equipment has been turned off, and there is the possibility of burns or electric shock. Be careful not to touch these areas. 쮕 쮕 쮕 쮕 쮕 das xenon assy nach ausschalten ...
Page 57
Page 57 never use any solvent products to clean the fibre optic cable as the solvent may cause irreparable damage. Clean the end of the fibre-optic cable regularly. If the end of the fibre-optic cable becomes dirty, the target assys may not detect the light emitted from the gun assy, and fail to reg...
Page 58
Page 58 8-2 error messages when an error is generated, the 7-segment score display indicates an error number, and the game makes an announcement repeatedly to call service personnel. An error can be cancelled by turning the power off and back on, or by opening the service door and operating the test...
Page 59
Page 59 error motor location 7-segment score display payout motor 1 error payout motor 2 error payout motor 3 error left centre right error motor location 7-segment score display prize sensor 1 error prize sensor 2 error prize sensor 3 error left (lengthwise sensor) centre (lengthwise sensor) right ...
Page 60
Page 60 8-3 removing the target assemblies 1. Remove the upper rear door. 2. When removing the the target assemblies at either end, remove 3off pozi head screws (m5x12) and remove the side cover, then remove 2off cap screws (m5x12) to remove the guard. 3. Disconnect the 2 connectors. 4. Remove the l...
Page 61
Page 61 5. Remove 2off cap screw (m4x10) and remove the target assy. 6. Reassemble in reverse order. Cap screws (m4x10) target assy.
Page 62
Page 62 8-4 removing the target pc board 1. Remove the target assy. (see 8-3 page 60) 2. Remove the target pc board by gently pressing the latch hooks outwards, and lifting the target pc board clear. 3. Reassemble in reverse order. Note: when refitting the target pc board, align the pins with the ho...
Page 63
Page 63 8-5 removing the target assy 7-segment pc board 1. Remove the target assy. (see 8-3 page 60) 2. Remove 4off pozi head self-tapping screws (m4x10) and separate the target assy. 3. Remove the 7-segment pc board. 4. Reassemble in reverse order. Note: take care, when seperating the target assy, ...
Page 64
Page 64 8-5 removing the target assy lamps 1. Remove the lamp base by pressing down on the latch and tilting the lamp base forwards. 2. Remove the lamp by unscrewing it from the lamp holder. 3. Reassemble in reverse order. Lamp base latch lamp holders lamp base latch must be positioned at the top la...
Page 65
Page 65 8-6 removing the 7-segment score pc board 1. Remove the upper rear door. 2. Disconnect the connector. Remove 4off cap screws (m4x10) and remove the 7-segment score pc board. 3. Reassemble in reverse order. Note: to prevent serious electrical damage to the game ensure that the connector is re...
Page 66
Page 66 8-7 replacing the fluorescent lamp or starter 1. Open the hood. 2. Replace the fluorescent lamp or starter. 3. Close and lock the hood. Fluorescent lamp (15 watt) starter.
Page 67
Page 67 8-8 replacing the main pc board pc boards can be easily damaged by static electricity. To prevent static damage, service personel should touch an earthed metal part of the game to discharge any static they may have built up before touching the pc board. 1. Remove the lower rear door. 2. Disc...
Page 68
Page 68 8-9 replacing the drive pc board pc boards can be easily damaged by static electricity. To prevent static damage, service personel should touch an earthed metal part of the game to discharge any static they may have built up before touching the pc board. 1. Remove the lower rear door. 2. Dis...
Page 69
Page 69 8-10 removing the play panel 1. Open the hood, and remove the fluorescent lamp. ( for safety and to prevent damage to the fluorescent lamp). 2. Remove 3off security screw (m5x12), 2off security screw (m5x20) and 2off whizz nuts (m6). 3. Lift the play panel only sufficient to gain access to t...
Page 70
Page 70 8-11 replacing the play panel switches 1. Remove the play panel. (see 8-10 page 69) 2. Remove the switch and lamp assy by pulling it straight out from the switch body. 3. Reassemble in reverse order. Note: when replacing the switch / lamp assy ensure that the correct colour wires are refitte...
Page 71
Page 71 8-12 replacing the prize sensors 8-12-1 lengthwise front 1. Remove the play panel. (see 8-10 page 69) 2. Remove 2off cap screw (m4x16) 3. Disconnect the 3 connectors, and detach the sensor bracket (b) 4. Remove 1off cap screw (m3x12), flat washer (m3) and hex nut (m3) from the sensor. Replac...
Page 72
Page 72 8-12-2 lengthwise rear 1. Remove 3off cap screws (m4x16). 2. Disconnect the 3 connectors, and detach the sensor bracket (a). 3. Remove 1off cap screw (m3x12), flat washer (m3) and hex nut (m3) from the sensor. Replace the sensor. 5. Reassemble in reverse order. Note: ensure that the rear pri...
Page 73
Page 73 8-12-3 widthwise 1. Remove 2off cap screws (m4x10). 2. Disconnect the 3 connectors, and remove the sensor bracket. 3. Remove 1off cap screw (m3x12), flat washer (m3), hex nut (m3) from the sensor. Replace the sensor. 4. Reassemble in reverse order. Note: ensure that a sensor with a 2-pin con...
Page 74
Page 74 8-13 payout assemblies 8-13-1 removing the payout assy 1. Remove the upper rear door. 2. Disconnect the 2 connectors and disconnect the earth connector. 3. Loosen 1off cap screw (m5x12) located under the payout assy. Remove 2off cap screws (m5x12) located on both sides of the payout assy. 4....
Page 75
Page 75 8-13-2 replacing the payout sensor 1. Remove the payout assy. (see 8-13-1 page 74) 2. Remove 1off pozi button head screw (m3x8), with flat washer, and replace the payout sensor. 3. Reassemble in reverse order. Pozi button head screw (m3x8) (with flat washer) payout sensor.
Page 76
Page 76 8-13-3 replacing the payout motor 1. Remove the payout assy. (see 8-13-1 page 74) 2. Remove 2off cap screws (m4x10) and detach the guide base. 3. Loosen 1off double point screw (m4x8). 4. Remove 4off cap screws (m4x10) and remove the payout motor. 5. Reassemble in reverse order. Cap screw (m...
Page 77
Page 77 8-14 gun assembly 8-14-1 removing the gun assy 1. Remove the play panel. (see 8-10 page 69) 2. Remove 2off cap screws (m4x6) and remove the xenon assy cover. 3. Remove the fibre-optic cable from the holder. Cap screw (m4x6) cover xenon assy fibre-optic cable xenon pc board holder.
Page 78
Page 78 4. Remove 4off security screws (m5x20), disconnect the connector, and remove the gun assy. 5. Reassemble in reverse order. Note: in order to ensure the correct light output from the gun assy, the fibre-optic should be fitted as close as possible to the xenon tube. When installing the fibre o...
Page 79
Page 79 8-14-2 replacing the gun switch, trigger and lens 1. Remove 7off cap screws (m3x8) and remove gun body (r). The grip is permanently fixed to the gun body (r). 2. Disconnect the two fast-on terminals from the trigger switch. Cap screws (m3x8) grip gun body (r) lens gun switch fast-on terminal...
Page 80
Page 80 3. Replace the gun switch, trigger or lens and reassemble in reverse order. Note: if the fibre optic holder has come off, re-attach it by aligning the marking on the fibre optic holder with the marking on the gun body (l). Install the lens so that the convex (curved) surface is facing outwar...
Page 81
Page 81 8-14-3 replacing the gun harness 1. Remove the gun assy. (see 8-14-1 page 77) 2. Remove 2off cap screws (m3x6) that hold the harness guide in place, and detach the harness guide from the pipe bracket. 3. Remove 1off pozi button head screw (m5x20) and hex nut (m5). 4. Remove the pipe clip, pi...
Page 82
Page 82 7. Disconnect the 2off fast-on terminals from the gun s w itc h 8. After removing the gun switch and trigger, remove 1off self tapping screw (m3x8) and detach the gun bracket. 9. Remove the flange nut (m3) to remove the pipe clip and sleeve. 10. Separate the fibre holder into two parts, and ...
Page 83
Page 83 8-15 xenon assembly l l l l l the xenon assy will remain hot and have areas of high voltage even though the equipment has been tuned off, and there is the possibility of burns or electric shock. Be careful not to touch these areas. 쮕 쮕 쮕 쮕 쮕 das xenon assy nach ausschalten des gerätes noch h...
Page 84
Page 84 8-15-1 replacing the xenon pc board pc boards can be easily damaged by static electricity. To prevent static damage, service personnel should touch an earthed metal part of the game to discharge any static they may have built up before touching the pc board. 1. Remove the play panel. (see 8-...
Page 85
Page 85 4. Disconnect the connector. 5. Using needle nosed pliers, squeeze the locking tabs of the locking supports, one at a time, to release the pc board. Remove the xenon pc board. 6. Reassemble in reverse order. Note: to prevent possible electrical damage, ensure that connectors are refitted the...
Page 86
Page 86 8-15-2 replacing the xenon drive pc board pc boards can be easily damaged by static electricity. To prevent static damage, service personel should touch an earthed metal part of the game to discharge any static they may have built up before touching the pc board. When installing the fibre op...
Page 87
Page 87 8-15-3 removing the xenon fan and filter 1. Remove 2off cap screws (m4x6) and remove the filter bracket. 2. Remove the filter from inside the filter bracket. 3. Disconnect the connector, remove 4off pozi head screws (m4x35), with spring and toothed lock washers, and remove the xenon fan 4. R...
Page 88
Page 88 9. Parts 9-1 upper cabinet assy 1 3 15 16 4 5 7 8 11 12 12 10 11 12 13 11 10 9 10 6 2 14 m e t i n o i t p i r c s e d o n t r a p 1 r e v o c t e g r a t 0 6 1 - 3 0 7 - p b x 2 r e v o c e d i s 1 6 1 - 3 0 7 - p b x 3 l e n a p t e g r a t 2 6 1 - 3 0 7 - p b x 4 t e n i b a c r e p p u 3...
Page 89
Page 89 9-2 target assy z target (a) target (b) target (c) target (d) a-a a-a z a a 1 5 6 2 4 7 3 9 8 10 m e t i n o i t p i r c s e d o n t r a p 1 ) a ( l e n a p r e t c a r a h c 0 7 1 - 3 0 7 - p b x ) b ( l e n a p r e t c a r a h c 5 7 1 - 3 0 7 - p b x ) c ( l e n a p r e t c a r a h c 7 7 1...
Page 90
Page 90 9-3 lower cabinet assy (1) b-b b-b a a b b a-a a-a c-c c-c c c y x - x y fork here fork here z ( on opposite side) 15 11 10 1 13 15 30 28 17 20 9 18 8 21 5 12 27 26 16 18 3 25 7 6 29 14 2 19 4 main main pc board pc board drive drive pc board pc board 22 23 24 31 z.
Page 91
Page 91 m e t i n o i t p i r c s e d o n t r a p 1 t e n i b a c r e w o l 0 8 1 - 3 0 7 - p b x 2 l e n a p e c n a n e t n i a m 1 8 1 - 3 0 7 - p b x 3 l e n a p l o r t n o c 2 8 1 - 3 0 7 - p b x 4 ) a ( y a t s r o s n e s 4 8 1 - 3 0 7 - p b x 5 ) b ( y a t s r o s n e s 5 8 1 - 3 0 7 - p b ...
Page 92
Page 92 9-4 lower cabinet assy (2) b-b b-b a a b b a-a a-a c-c c-c c c y x namco limited x y fork here fork here fork here fork here z 41 36 58 49 55 37 43 44 45 48 42 46 57 38 39 56 57 47 35 34 32 40 33 48 operators manual 52 main main pc board pc board driver driver pc board pc board z.
Page 93
Page 93 m e t i n o i t p i r c s e d o n t r a p 2 3 t e k c a r b r e t s u j d a 0 2 1 - 0 5 4 - p b x 3 3 p x e ) e c n a n e t n i a m ( l a c e d n o i t u a c 9 5 3 - 1 6 4 - p b x 4 3 ) 5 7 x 6 1 m ( t o o f e l b a t s u j d a 9 7 0 0 0 3 8 8 5 3 r o t s a c l e v i w s 9 9 1 - 2 0 1 - p b ...
Page 94
Page 94 9-5 payout assy 4 3 2 1 6 7 5 m e t i n o i t p i r c s e d o n t r a p 1 l a r i p s e z i r p 0 2 2 - 3 0 7 - p b x 2 e d i u g l a r i p s 1 2 2 - 3 0 7 - p b x 3 t e k c a r b r o t o m 2 2 2 - 3 0 7 - p b x 4 e s a b e d i u g 1 1 7 - 9 9 6 - p b x 5 t il s r o s n e s 2 1 7 - 9 9 6 - p...
Page 95
Page 95 9-6 gun assy 4 7 12 5 13 10 19 8 9 14 16 3 1 15 2 18 6 11 17 m e t i n o i t p i r c s e d o n t r a p 1 e s o h e l b i x e l f 0 3 2 - 3 0 7 - p b x 2 e r b i f n u g 1 3 2 - 3 0 7 - p b x 3 t e k c a r b n u g 1 1 6 - 6 8 6 - c q x 4 e ) l ( y d o b n u g p i r g d n a y d o b n u g t e s...
Page 96
9-7 mains-in assy 3 1 2 m e t i n o i t p i r c s e d o n t r a p 1 x o b d r o c 0 5 7 - 1 6 4 - p b x 2 ) 6 0 - 6 - 2 2 2 9 n f ( r e t li f n i - s n i a m 8 2 1 - 7 0 0 - p b x 3 ) t n u o m l e n a p - m m 0 2 ( r e d l o h e s u f 6 8 7 0 0 5 3 6 ) m m 0 2 - b / q a 5 ( e s u f 1 0 6 0 0 5 3 6.
Page 97
9-8 coin door volume min. Max. Select off test on service prize counter 6 5 4 3 2 1 z z sw. Sw. Sw. 9 1 7 5 6 2 3 4 8 m e t i n o i t p i r c s e d o n t r a p 1 y s s a r o o d n i o c 7 8 1 - 0 0 1 - p b x 2 r e k c i t s e c i v e s 3 7 1 - 1 6 4 - p b x 3 h c t i w s n o t t u b h s u p 9 5 0 0 ...
Page 98
Page 98 1 9-9 xenon assy m e t i n o i t p i r c s e d o n t r a p 1 s i s s a h c 4 4 0 0 0 0 7 4 2 e t a l p g n i t n u o m b c p 3 4 0 0 0 0 7 4 3 r e v o c 5 4 0 0 0 0 7 4 4 t e k c a r b g n i t n u o m r e t li f 2 4 0 0 0 0 7 4 5 h s e m r e t li f n a f 6 4 0 0 0 0 7 4 6 r e t li f 1 4 0 0 ...
Page 99
230v ac mains-in grn/yel blue brown 5 amp q/b 2 amp q/b 17 19 18 16 (grn/yel) lamp fixture fluorescent org 6. Wire colours indicated in parenthesis () are for accessory gland and indicated for reference only. 5. Transformer (300d) assy is used in export models, and input terminal connections must co...
Page 100
Red red lower cabinet 3. Socket and pin contacts are used respectively for plug and cap connectors. 2. Miniature universal mate-n lock connectors are used unless otherwise specified. 1. Thick green/yellow, thick, and thin lines represent awg16, awg18 and awg24, respectively, unless otherwise specifi...
Page 101
For all parts or technical support contact: brent electronic, namco house, units 7-8, acton park estate, the vale, london. W3 7qe www.Namco.Co.Uk for technical support, warranty and advance replacement parts:- +44 (0) 20 8324 6120 for consumable parts:- +44 (0) 20 8324 6102 fax for both:- +44 (0) 20...