NAMCO Quick & Crash Operator's Manual

Page of 131

Download

Print this page

Bookmark us

OPERATORS MANUAL

THE

RESPONSIBILITY

THE

OPERATOR

MAINTAIN

CUSTOMER

SAFETY

ALL

TIMES

AND

IMPERATIVE

THAT

THE

DETAILS

SET

OUT

THIS

MANUAL

ARE

FOLLOWED

PRECISELY

Part No. 90500074

Issue 1

QUICK & CRASH

1 2 3 4 5 6 7 Next › »

Summary of Quick & Crash

Page 1
Operators manual i t is the responsibility of the operator to maintain customer safety at all times , and it is imperative that the details set out in this manual are followed precisely part no. 90500074 issue 1 quick & crash.
Page 2: Contents
Page 2 contents operators manual ............................................................................................................................. 1 general safety considerations .................................................................................................. 4 allgemei...
Page 3
Page 3 7. Maintenance .................................................................................................................................. 46 7-1 regular cleaning ...................................................................................................................... 48 7...
Page 4
Page 4 no part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without permission from namco europe limited. While the i...
Page 5
Page 5 removing and replacing parts adjustments or maintenance on this equipment should be carried out by suitably qualified personnel only. Do not make any alteration to this equipment without prior approval. Doing so could cause unforeseeable danger. Only parts specified by namco europe ltd. Shoul...
Page 6
Page 6 dieses dokument darf in keiner weise vervielfältigt werden. Jegliche tonaufnahmen sowie die speicherung auf datenträger (suchsysteme), die weitergabe oder sonstiges kopieren für den gewerblichen und privaten gebrauch sind untersagt und bedürfen der vorherigen genehmigung durch namco europe li...
Page 7
Page 7 hinweise zur aufstellung niemals das gerät einschalten bevor die aufstellung völlig abgeschlossen ist. Zur vermeidung von elektroschlägen muß das gerät mit einem ordnungsgemäß geerdetem netzstecker an die stromversorgung angeschlossen werden. Um zu vermeiden, daß kunden durch die gerätebewegu...
Page 8
Page 8 denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra namco europe limited...
Page 9
Page 9 punkter om installation tænd aldrig for strømmen til maskinen før installering er fuldført. For at undgå mulige elektriske stød sikres, at maskinen er forbundet til hovedstrømmen med sikkert monterede jordstik. For at kunder ikke kommer til skade ved spillets bevægelser sikres, at der er mind...
Page 10
Page 10 no se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para uso público o privado, sin permiso de namco europe limited. Si bien la i...
Page 11
Page 11 retirar y reemplazar partes y unidades . Las revisiones de instalación, los ajustes, y el mantenimiento rutinario deberán llevarse a cabo sólo por personal cualificado. No realice alteraciones en esta máquina sin aprobación previa. De hacerlo así, pueden causar peligros imprevisibles. Sólo d...
Page 12
Page 12 aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen denregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique...
Page 13
Page 13 notes dinstallation ne jamais mettre le jeu en marche avant que linstallation ne soit complétement effectuée. Afin de prévenir une éventuelle électrocution, sassurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité. Afin que les clients ne...
Page 14
Page 14 Κανένα µέρος αυτής της έκδοσης δεν µπορεί να αναπαραχθεί µε οποιοδήποτε µηχανικ# ,φωτογραφικ# ή ηλεκτρονικ# µέσο , ή µε µορφή φωνητικής ηχογράφησης και ούτε να αποθηκευτεί µε επανορθωτικ# σύστηµα , να µεταδοθεί ή να αντιγραφεί για δηµ#σια ή ιδιωτική χρήση , χωρίς την άδεια της namco europe l...
Page 15
Page 15 ΑΠΟΜΑΚΡΥΝΣΗ ΚΑΙ ΑΝΤΙΚΑΤΑΣΤΑΣΗ ΜΕΡΩΝ - ΑΝΤΑΛΛΑΚΤΙΚΩΝ Εγκατ&σταση , µετατροπ$ $ λεγχος ρουτνας µπορε να γνεται µνο απ εξουσιοδοτηµνα &τοµα . ∆εν πρπει να γνονται µετατροπς στα µηχαν$µατα ωρς γκριση . Μπορε να προκληθε απρβλεπτος κνδυνος. Μνο µρη που διευκρινζονται απ την εταιρεα ;bcd: efg:he i...
Page 16
Page 16 nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza lautorizzazi...
Page 17
Page 17 notes dinstallation non accendere mai la macchina finchè linstallazione non è stata completata. Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure. Perchè i clienti non si...
Page 18
Page 18 ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra namco europe limited. Da in...
Page 19
Page 19 fjerne og utskifte enheter og deler. Installasjon, service, justering eller rutine vedlikehold skal bare utføres av kvalifiserte personer. Ikke lag noen forandringer på denne maskinen uten godkjenning. Dette kan medføre uforutsette farer. Bare deler spesifisert av namco europe ltd. Skal beny...
Page 20
Page 20 niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toest...
Page 21
Page 21 het spel is voorzien van wieltjes, waardoor het gemakkelijker is om te verplaatsen. Wees voorzichtig als de machine op een hellend vlak gereden wordt. Het zwaartepunt van de header assembly ligt aan diens voorkant, waardoor het belangrijk is dat minimaal 2 personen de header assembly aanbren...
Page 22
Page 22 nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos transmissiveis ou de outra forma copiados para uso publico ou privado sem a...
Page 23
Page 23 esta maquina está equipada com rodas afim de facilitar a sua deslocação tenha cuidado ao mover a maquina num plano inclinado. O bloco superior (cabeça) tem o centro de gravidade para a frente, porconseguinte é importante que pelo menos sejam utilizadas duas pessoas para montar ou desmontar e...
Page 24
Page 24 ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för offentlig eller privat användning, utan tillstånd från namco europe limi...
Page 25
Page 25 att beakta vid installation sätt aldrig på strömmen på maskinen innan installationen är klar. För att förhindra elektriska chocker, försäkra dig om att maskinen kopplas till strömförsörjning med jordad kontakt för att undvika skador av spelets rörelser, försäkra dig om att det finns ett avst...
Page 26
Page 26 tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman namco europe limited :in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. Namco europe limited:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite...
Page 27
Page 27 asennushuomioita Älä koskaan kytke laitetta päälle ennen kuin asennus on suoritettu loppuun. Tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sähköiskun vaaraa ei olisi. Varmista, että laitteen ja seinän tai toisen laitteen välissä on vähintään...
Page 28
Page 28 1. Specifications power requirements:- 230v / 180watts ac ambient operating +5°c to +25°c temperature:- coin acceptor:- mars cashflow - single channel dimensions:- assembled 760(w) x 2,430(d) x 2,050(h) gun cabinet 550(w) x 1,670(d) x 930(h) target cabinet 760(w) x 1,000(d) x 1,670(h) header...
Page 29
Page 29 2. How to play game description this game is a quick draw shooting game where the player draws a gun, aims at the targets that appear and tries to hit the targets as quickly as possible. A target appears as soon as the gun is drawn from the holster and the player tries to complete the four...
Page 30
Page 30 3. Major components signboard assy dot matrix display rear fluorescent tubes flat target (u) assy flat target (l) assy shutter assy front fluorescent tube time display 7 segment pc board target cabinet gun cabinet castor adjustable foot gun assy [set] lamp [start] lamp instruction panel top ...
Page 31
Page 31 4. Moving the machine this equipment is fitted with castors to make it easier to move. Take care when moving the equipment on an inclined floor. The overall height of this equipment is 2050mm. Take care of any overhead obstructions. (e.G. Light fittings, electric cables etc.) warning never t...
Page 32
Page 32 dieses gerÄt ist nur fÜr die gewerbliche aufstellung in geschlossenen rÄumen bestimmt. Das gerÄt darf an folgenden plÄtzen nicht aufgestellt werden 1. Im freien. 2. In direktem sonnenschein, an extrem feuchten und staubigen plätzen, an plätzen mit wasseranschlüssen und möglichen leckagen, na...
Page 33
Page 33 ও denne maskinen er bare konstruert for innendØrs bruk ikke installer maskinen pÅ fØlgende plasser. 1. Utendørs 2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje, nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur. 3....
Page 34
Page 34 esta maquina foi concebida para utilizaÇÃo em espacos interiores apenas nÃo instalar a maquinas nos seguintes locais:- 1. Exteriores. 2. `luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de água perto de ar condicionados ou equipamentos calorificos e locais ...
Page 35
Page 35 5-1 joining the front and rear cabinets 1. Remove 4off button head screws (m8x35) and remove the joint brackets from inside the gun cabinet. (do not lose the screws as these are required for refitting later). 2. Fit the joint brackets to the target cabinet with 6off button head screws (m8x35...
Page 36
Page 36 3. Connect the connectors and slide the gun cabinet upto the target cabinet, taking care not to trap any wires, and retain using the 4off button head screws removed in 1 above. 4. When the game is fully assembled and in its correct position, lower the four level adjusters on the gun cabinet...
Page 37
Page 37 5-2 removing the flat target packing. 1. Remove the four off button head screws (m5x35) and remove the rear upper door on the target cabinet. ( note: take care that the door does not fall when removing the four screws ). 2. Remove the cardboard packing from both the upper and lower flat targ...
Page 38
Page 38 6. Adjustments g adjustment or maintenance on this machine should be carried out by qualified personnel only. D einstellungen und wartung des gerätes dürfen nur von dafür qualifiziertem fachpersonal vorgenommen werden. L justeringer eller vedligehold af denne maskine bør kun udføres af kvali...
Page 39
Page 39 6-1 adjustment switches the adjustment switches are located inside the coin door. 1. Service switch. Press this switch to obtain game credits without incrementing the play meter, to change the settings when in the setting mode and to select test numbers when in the test mode. 2. Test switch ...
Page 40
Page 40 6-2 setting mode this mode allows the changing of various game and price settings. 6-2-1 setting mode operation 1. Slide the test switch on while pushing the select switch. 2. The item and settings are displayed on the dot matrix display. The selected item changes each time the select switch...
Page 41
Page 41 6-2-2 ticket payout setting n do not operate in ticket mode without a ticket dispenser connected 1. Free ticket setting this setting when on will pay one ticket at the end of each game if no score tickets have been awarded. 2. Ticket payout no. Setting this sets the number of tickets to be p...
Page 42
Page 42 6-3 test mode 1. Open the coin door and slide the test switch on. The test item and test no. (number) are displayed on the dot matrix display. 2. Press the select switch to step to the next item. 3. Press the service switch to change the test no. (number). Each time the service switch is p...
Page 43
Page 43 6-4 adjusting the launcher solenoid the launcher solenoid must be adjusted after replacement. 1. Loosen the 4off socket flange head screws (m6x10), only sufficiently so that the solenoid bracket can just be moved by hand. If the screws are loosened too much it will make it difficult to adjus...
Page 44
Page 44 6-5 adjusting the shutter solenoid the shutter solenoid must be adjusted after replacement. 1. Loosen the 4off socket flange head screws (m5x8), only sufficiently so that the solenoid can just be moved by hand. If the screws are loosened too much it will make it difficult to adjust the solen...
Page 45
Page 45 6-6 adjusting the flat target (u)/(l) solenoids the flat target (u)/(l) solenoid must be adjusted after replacement. 1. Loosen the 4off socket flange head screws (m5x8), only sufficiently so that the solenoid can just be moved by hand. If the screws are loosened too much it will make it diff...
Page 46
Page 46 7. Maintenance g adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the power to the machine is turned off before commencing any maintenance work. (trouble shooting, service or repairs etc.) d einstellungen und wartung des gerätes dürfen ...
Page 47
Page 47 o aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine uitgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.) p afinações ou manutenção nesta maquina, deverão ser efectuadas ...
Page 48
Page 48 7-1 regular cleaning this game relies upon light to operate correctly and it is important that glasses, mirrors, sensors and lenses are kept clean. Never use any solvent products to clean the above items as the solvent may cause irreparable damage. 7-1-1 cleaning the glasses and half mirror....
Page 49
Page 49 7-1-3 cleaning the cup target sensor never use any solvent products to clean the sensor as the solvent may cause irreparably damage. 1. Remove the display cover as described in section 7-9 page 62. 2. Remove the maintenance door as described in section 7-10 page 64 3. Move the cup target cov...
Page 50
Page 50 7-1-4 cleaning the gun lens never use any solvent products to clean the lens as the solvent may cause irreperable damage. 1. Wipe and clean the surface of the gun lens with a clean, dry, lint free cloth. Gun assy lens soft, dry cloth.
Page 51
Page 51 7-1-5 cleaning the fibre optic cable never use any solvent products to clean the fibre optic cable as the solvent may cause irreparable damage. 1. Remove the fibre optic cable as described in section 7-30 page 93 2. Wipe and clean the surface of the fibre optic lens with a clean, dry, lint f...
Page 52
Page 52 7-1-6 cleaning the gun holster detection sensor never use any solvent products to clean the lens as the solvent may cause irreparable damage. 1. Remove the holster cover as described in section 7-26 page 87. 2. Wipe and clean the surface of the gun holster detection sensor with a clean, dry,...
Page 53
Page 53 7-2 replacing the game pc board note: the game pc board is susceptible to damage from static electricity. Anti static precautions should be taken when removing, handling and refitting the game pc board. 1. Remove the 2off button head screws (m5x35) and remove the rear maintenance door (l) of...
Page 54
Page 54 7-3 replacing the cup target sensor pc board 1. Remove the upper rear maintenance door from the target cabinet. 2. Remove the connectors. 3. Using needle nosed pliers, squeeze the locking tabs of the locking supports, one at a time, to release the pc board. Remove the sensor pc board. 4. Rep...
Page 55
Page 55 7-4 replacing the rear glass 1. Remove the upper rear maintenance door from the target cabinet. 2. Remove 4off pozi flange head screws (m5x12) and remove the chip slope (l). 3. Remove 4off pozi flange head screws (m5x12) and remove the chip slope (r). 4. Remove the 4off button head screws (m...
Page 56
Page 56 7-5 replacing the light guard 1. Remove the upper rear door from the target cabinet. 2. Remove 3off pozi head screws (m4x16) and remove the light guard in the direction of the arrow in the diagram below note: the rear glass is located below the light guard. Take care not to drop anything on ...
Page 57
Page 57 7-6 replacing the rear fluorescent tubes and starters. 1. Remove the light guard. (see section 7-5 page 56). 2. Replace the fluorescent lamp or starter. Note: the fluorescent lamp has an effect on the appearance of the game field, so replace only with 20 watt coolwhite fluorescent. Starter 2...
Page 58
Page 58 7-7 replacing the front acrylic 1. Remove 6off security screw (m5x12) and remove the header front cover. 2. Disconnect the two connectors: cn11 and cn12. 3. Remove 4off pozi head screws (m5x25) and pull the header panel forward a little to unfasten it from the hooks, and disconnect the conne...
Page 59
Page 59 4. Remove the 4off security screws (m5x12) and remove the front acrylic retaining brackets. Note: the front acrylic will tilt forward when the retaining brackets are moved, so ensure that the acrylic is being held in place with a hand. 5. The front acrylic sits in a groove on the target cabi...
Page 60
Page 60 7-8 replacing the half mirror 1. Remove the front acrylic. (see section 7-7 page 58). 2. Remove the 4off button head screws (m5x16) and remove the upper half mirror retaining brackets (left and right). 3. Only loosen the 4off button head screws (m5x16) retaining the lower half mirror retaini...
Page 61
Page 61 indicator label target cabinet half mirror 4. Hold the mirror both top and bottom and remove it in the direction of the arrow, as shown in the diagram below. 5. Refit the half mirror in the reverse order. Note: there is a small label in the upper left corner of the mirror to indicate the fro...
Page 62
Page 62 7-9 replacing the 7-segment pc board note: the 7-segment pc board is susceptible to damage from static electricity. Anti static precautions should be taken when removing, handling and refitting the 7-segment pc board. 1. Remove 4off security screw (m5x30) and remove the display cover. 2. Rem...
Page 63
Page 63 3. Remove 6off pozi head screws (m4x12) that retain the 7-segment pc board. 4. Disconnect the connector and remove the 7-segment display pc board. 5. Refit in the reverse order. Display bracket 7-segment pc board pozi head screw (m4x12) display bracket 7-segment pc board connector.
Page 64
Page 64 7-10 replacing the front fluorescent and starter 1. Remove the display cover. (see section 7-9 page 62) 2. Remove 2off security screws (m5x35) that retain the front maintenance door. Pull the front maintenance door forward in the direction of the arrow, as shown in the diagram below, only su...
Page 65
Page 65 3. Only loosen 2off pozi flange head screws (m4x8) and remove the cover b. 4. Replace the fluorescent tube or starter. 5. Reassemble in reverse order. Note: the fluorescent lamp has an effect on the appearance of the game field, so replace only with 20 watt coolwhite fluorescent. Pozi flange...
Page 66
Page 66 7-11 replacing the cup target sensor assy 1. Remove the upper rear maintenance door from the target cabinet. 2. Remove the display cover and front maintenance door. (see section 7-10 page 64) . 3. Disconnect connector j301 from the sensor pc board and free the harness from the front of the t...
Page 67
Page 67 5. Remove 3off pozi head head screws (m4x12) and remove the cup target sensor from the mounting bracket. 6. Replace the sensor assy and reassemble in reverse order. Connector j301 cup target pozi head screw (m4x12) cup target sensor assy pozi head screw (m4x45) (with flat and spring washers)...
Page 68
Page 68 7-12 replacing the header fluorescent and starter. 1. Remove the header front cover. (see section 7-7 page 58) 2. Replace the fluorescent tube or starter. 3. Reassemble in reverse order. Lamp 24v / 15w starter fluorescent tube (15watt) lamp 24v / 15w.
Page 69
Page 69 lamp 24v / 15w 7-13 replacing the header lamp 1. Remove the header front cover. (see section 7-7 page 58) 2. Remove the header lamp by unscrewing the lamp in the direction of the arrow, shown in the diagram below. 3. Replace the lamp and reassemble in reverse order..
Page 70
Page 70 7-14 replacing the dot matrix display. 1. Remove the header front cover. (see section 7-7 page 58) 2. Remove 2off pozi head screws (m4x12) and remove the dot matrix cover. 3. Remove the 4off pozi head screw (m5x25), 1off lock washer and ring tag terminal and gently pull the display bracket f...
Page 71
Page 71 4. Disconnect the connectors (cn45 and cn46), remove 4off pozi head screw (m4x12) and remove the dot matrix display from the display bracket. 5. Reassemble in the reverse order. Display bracket dot matrix assy pozi head screw (m4x12) connector (cn46) connector (cn45).
Page 72
Page 72 7-15 replacing the launcher solenoid 1. Remove the upper rear maintenance door from the target cabinet. 2. Remove 1off pozi flange head screw (m4x6) and disconnect the ring tag terminal and connector (cn25). 3. Remove 4off socket flange screws (m6x10), with flat and spring washers, and remov...
Page 73
Page 73 7-16 replacing the launcher sensor 1. Remove the upper rear maintenance door from the target cabinet. 2. Disconnect the connector (cn26). 3. Remove 2off pozi flange head screws (m4x6) and remove the launch sensor complete with sensor bracket. 4. Remove 1off pozi head screw (m4x12) and remove...
Page 74
Page 74 7-17 replacing the shutter solenoid 1. Remove the front maintenance door from the target cabinet (see section 7-10 page 64) . 2. Disconnect connector (cn28). 3. Remove 4off socket flange screws (m5x8) and remove the shutter solenoid. Socket flange screw (m5x8) ring tag connector (cn28) shutt...
Page 75
Page 75 solenoid plunger delrin washer install the solenoid spring (s) so the spring hook comes in contact with the side of the spacer (6dia x 5) flat washer (m6) e-clip spacer (6dia x 5) solenoid shaft spring hook solenoid spring spacer (6dia x 10) tension spring 4. To remove the solenoid plunger r...
Page 76
Page 76 7-17 replacing the shutter sensor 1. Remove the front maintenance door from the target cabinet (see section 7-10 page 64). 2. Disconnect connector (cn30). 3. Tilt the cup target cover in the direction of arrow (a), shown in the diagram below. Remove 2off flange socket head screws (m5x8) and ...
Page 77
Page 77 7-18 removing the flat target assembly 1. Remove the upper rear door from the target cabinet. 2. Disconnect the connectors (cn20) and (cn22), remove 2off pozi flange head screws (m4x6) to release the harnesses. 3. Disconnect the connectors (cn21) and (cn29). 4. Remove 4off (2ea left and righ...
Page 78
Page 78 7-19 replacing the flat target solenoid 1. Remove the flat target assy. (see section 7-18 page 77) 2. Remove the pozi flange head screw (m4x6) to release the nylon clip retaining the harness coming from connector (cn20). 3. Remove 4off flange socket head screws (m5x8) and remove the ring tag...
Page 79
Page 79 e-clip solenoid shaft flat washer (m6) arm shaft spacer solenoid spring spring spacer flat washer (m6) e-clip solenoid plunger flat target solenoid e-clip solenoid spring spring spacer e-clip spring hook arm shaft spacer 4. To remove the solenoid plunger, remove one of the e-clips and flat w...
Page 80
Page 80 7-20 replacing the flat target drive cable 1. Remove the upper rear maintenance door from the target cabinet. 2. Remove 2off flange socket screws (m4x6) and remove the flat target drive cable. 3. Reassemble in reverse order. Note: when refitting the flat target drive cable ensure that the ca...
Page 81
Page 81 7-21 replacing the flat target motor 1. Remove the upper rear maintenance door from the target cabinet. 2. Remove the flat target drive cable (see section 7-20 page 80). 3. Disconnect connectors (cn21) and (cn24). 4. Loosen 2off double point screws (m5x6) and remove the pulley in the directi...
Page 82
Page 82 6. Replace the motor and reassemble in reverse order. Note: the shaft of the flat target motor has been ground flat in two places. When replacing the pulley ensure that the two double point screws are in contact with these flat faces. Before tightening the double point screws ensure that the...
Page 83
Page 83 7-22 replacing the flat target sensor pc board note: pc boards are susceptible to damage from static electricity. Anti static precautions should be taken when removing, handling and refitting the pc board. 1. Remove the flat target assembly. (see section 7-18 page 77). 2. Disconnect connecto...
Page 84
Page 84 7-23 replacing the flat target position detection sensor 1. Remove the upper rear maintenance door from the target cabinet. 2. Disconnect connector (cn48) 3. Remove 1off pozi head screw (m4x12) and remove the flat target position detection sensor 4. Reassemble in reverse order. Note: it is r...
Page 85
Page 85 flat target sensor assy target plate pozi flange screw (m4x6) flange socket screw (m4x10) flange socket screw (m4x12) connectors (cn50) flat target sensor assy 7-24 replacing the flat target sensor assy 1. Remove the flat target assembly. (see section 7-18 page 77). 2. Remove 2off pozi head ...
Page 86
Page 86 7-25 replacing the flat target origin sensor 1. Remove the upper rear maintenance door from the target cabinet. 2. Disconnect connector (cn24). 3. Remove 1off pozi head screw (m4x12) with flat washer (m4) and remove the flat target detection sensor. 4. Reassemble in reverse order. Note: it i...
Page 87
Page 87 7-26 replacing the gun detection sensor 1. Remove 1off security screw (m5x20), 1off security screw (m5x10) and remove the holder cover. 2. Remove 2off pozi head screws (m4x20) and remove the holder bracket (c). 3. Remove 2off pozi head screws (m4x25), with flat and spring washers, and remove...
Page 88
Page 88 4. Disconnect the connector (cn39). 5. Remove the pozi head screw (m3x12) and remove the gun detection sensor (projection side). 6. Reassemble in reverse order. Note : repeat above procedures to remove the gun detection sensor (receiving side). Holder bracket (l) connector (cn39) holder brac...
Page 89
Page 89 7-27 replacing the [set] and [start] lamps 1. Remove 6off security screws (m4x25), with flat washers, and remove the set / start acrylic. 2. Remove the lamp by turning it in the direction of the arrow, shown in the diagram below. 3. Reassemble in reverse order. Security screw (m5x25) gun cab...
Page 90
Page 90 7-28 replacing the speaker 1. Remove 5off security screws (m5x20) and remove the top cover. 2. Remove 4off pozi head screws (m5x25), with flat and spring washers, and lift the speaker box in the direction of the arrow, as shown in the diagram below. Security screw (m5x20) top cover gun cabin...
Page 91
Page 91 3. Remove the 4off self tapping screws (no8 x 5 / 8 ) and remove the speaker cover. 4. Remove the 4off , self tapping screws (no8 x 5 / 8 ) disconnect the faston terminals and remove the speaker. 5. Reassemble in reverse order. Note: if the wires to the speaker have been disconnected, en...
Page 92
Page 92 7-29 replacing the holder cushions (a) (b) (c) 1. Remove the holder cover and holder bracket (c). (see section 7-26 page 87) 2. The holder cushions (a) (b) (c) are attached using double-sided adhesive tape. Pull firmly on the cushion and peel it from the holder bracket. 3. Apply the new hold...
Page 93
Page 93 7-30 replacing the xenon pc board note: pc boards are susceptible to damage from static electricity. Anti static precautions should be taken when removing, handling and refitting the pc board. 1. Remove 2off button head screws (m5x35) and remove the front maintenance door from the gun cabine...
Page 94
Page 94 tab needle nosed pliers stopper locking support pc board 3. Disconnect connector (cn41) and the fibre optic in the direction of the arrow, as shown in the diagram below. 4. Using needle nosed pliers, squeeze the locking tabs of the locking supports, one at a time, to release the pc board. Re...
Page 95
Page 95 holder xenon tube xenon pc board insert the fibre optic until it comes in contact with the stopper in the holder and install it so that it is as close as possible to the xenon tube. Fibre optic 5. Reassemble in reverse order. Note: in order to ensure the correct light output from the gun ass...
Page 96
Page 96 tab needle nosed pliers stopper locking support pc board 7-31 replacing the xenon drive pc board note: pc boards are susceptible to damage from static electricity. Anti static precautions should be taken when removing, handling and refitting the pc board. 1. Remove the xenon cover. (see sect...
Page 97
Page 97 7-32 removing the xenon fan and filter 1. Remove 2off pozi head screws (m4x12) and remove the filter bracket. 2. Remove the filter from inside the filter bracket. 3. Disconnect connector (cn37), remove 4off pozi head screws (m4x45), with spring and toothed lock washers, and remove the xenon ...
Page 98
Page 98 7-33 replacing the gun assy note: when removing the gun assy from the top cover on the gun cabinet, take care not to bend, pull or scratch the harness or fibre optic cable. 1. Remove the fibre optic cable. (see section 7-30 page 93) 2. Remove 4off security screw (m5x10) that retains the pipe...
Page 99
Page 99 7-34 replacing the gun switch, trigger and lens 1. Loosen 2off screws (m3x8) retaining the gun sight. 2. Remove 7off cap bolts (m3x8) and remove gun side (r). The grip is permanently fixed to the gun side (r). 3. Disconnect the two faston terminals to remove the gun switch, trigger and lens....
Page 100
Page 100 4. Replace the gun switch, trigger or lens and reassemble in reverse order. Note: if the fibre optic holder has come off, reattach it by aligning the marking on the fibre optic holder with the marking on the gun side (l). Install the lens so that the convex (curved) surface is facing outwar...
Page 101
Page 101 7-35 replacing the gun harness assy 1. Remove the fibre optic cable. (see section 7-30 page 93) 2. Remove 2off cap bolts (m3x6) and remove the harness guide from the pipe bracket. 3. Remove 1off pozi head screw (m5x20), hex nut (m5) and unfasten the pipe clip and pipe bracket. 4. Remove 1of...
Page 102
Page 102 5. Remove the gun side (r) and grip (r). (see section 7-34 page 99). 6. Disconnect the 2off fast-on terminals from the gun switch. 7. After removing the gun switch and trigger, remove 1off self tapping screw (m3x8) and remove the gun bracket. 8. Remove 1off flange nut (m3) and remove the pi...
Page 103
Page 103 tie wrap gun bracket 10 reassemble in reverse order. Note: the tie wraps on the gun harness assembly should be installed so that they come in contact with the gun bracket, as shown in the diagram below. Note: install the fibre optic holder by aligning the marking on the holder with the mark...
Page 104
Page 104 8. Error messages this game is constantly monitoring its operation. If an error is detected, a message is displayed on the dot matrix display, an error code is displayed on the 7 segment display and an audible warning sounded. For errors to in the table below, the message please call atten...
Page 105
Page 105.
Page 106
Page 106 9. Parts 20 15 25 30 45 40 39 24 41 40 39 27 10 11 7 24 17 18 19 22 5 4 1 2 3 7 12 25 26 27 29 30 31 32 gun cabinet.
Page 107
Page 107 m e t i n o i t p i r c s e d o n t r a p 1 g n i h s u b g n i t n u o m n u g 7 8 9 - 4 9 6 - c q x 2 e t a l p g n i t n u o m n u g 6 8 9 - 4 9 6 - c q x 3 m r o f - c a v r e k a e p s d u o l 6 3 0 0 0 0 7 4 4 h s e m r e k a e p s d u o l 7 3 0 0 0 0 7 4 5 e g n a r ll u f " ½ 5 r e ...
Page 108
Page 108 15 9 7 9 4 1 2 13 16 19 21 25 23 22 16 15 29 27 40 31 34 35 36 37 38 32 5 5 6 3 14 target cabinet 1.
Page 109
Page 109 m e t i n o i t p i r c s e d o n t r a p 1 x e p s r e p t n o r f 2 6 0 0 0 0 7 4 2 p a r t s g n i n i a t e r x e p s r e p t n o r f 3 6 0 0 0 0 7 4 . 3 t e k c a r b p m a l c r e t u o r o r r i m 8 6 0 0 0 0 7 4 4 r o r r i m 5 6 0 0 0 0 7 4 5 t e k c a r b p m a l c r e n n i r o r...
Page 110
Page 110 42 41 49 50 48 43 47 51 45 43 53 54 56 57 43 63 64 72 66 59 52 44 73 65 67 target cabinet - 2.
Page 111
Page 111 m e t i n o i t p i r c s e d o n t r a p 1 4 r e v o c x e p s r e p e b u t t n e c s e r o u l f 6 7 0 0 0 0 7 4 2 4 r e p p u - t e k c a r b g n i n i a t e r x e p s r e p e b u t t n e c s e r o u l f 7 7 0 0 0 0 7 4 3 4 d e d i s e l b u o d - m m 5 x m m 0 1 e g n o p s k c a l b 7...
Page 112
Page 112 m e t i n o i t p i r c s e d o n t r a p 1 m r o f - c a v r e d a e h 8 5 0 0 0 0 7 4 2 c il y r c a r e d a e h 4 4 5 0 0 0 0 4 3 c il y r c a p m a l 6 4 5 0 0 0 0 4 4 t e k c a r b g n i t n u o m r e p p u m r o f - c a v r e d a e h 1 6 0 0 0 0 7 4 5 t t a w 5 2 - " 8 1 - e b u t t n...
Page 113
Page 113 m e t i n o i t p i r c s e d o n t r a p 1 s i s s a h c 4 4 0 0 0 0 7 4 2 n a f n o n e x 5 6 0 3 5 - c q x 3 h s e m r e t li f n a f 6 4 0 0 0 0 7 4 4 r e t li f 1 4 0 0 0 0 7 4 5 t e k c a r b g n i t n u o m r e t li f 2 4 0 0 0 0 7 4 6 e t a l p g n i t n u o m b c p 3 4 0 0 0 0 7 4 ...
Page 114
Page 114 1 2 3 5 4 8 9 13 12 14 15 16 17 11 7 6 10 launcher assembly.
Page 115
Page 115 m e t i n o i t p i r c s e d o n t r a p ) y s s a r e h c n u a l ( y l b m e s s a m s i n a h c e m n o i s o l p x e p u c h c e m - l p x e - c - c q x 1 d a e h 4 1 1 - 4 9 6 - c q x 2 m r a d i o n e l o s 5 1 1 - 4 9 6 - c q x 3 k c o l b m r a 0 2 1 - 4 9 6 - c q x 4 t e k c a r b...
Page 116
Page 116 a 12 32 31 30 29 14 28 23 25 24 21 13 20 22 19 18 13 12 13 9 14 17 16 9 8 13 15 12 9 11 9 5 7 6 1 2 3 9 10 4 27 26 flat target (upper) assembly - 1.
Page 117
Page 117 m e t i n o i t p i r c s e d o n t r a p ) y s s a t e g r a t b u s ( y s s a ) r e p p u ( t e g r a t t a l f h c e m - r a t - u - c q x 1 ) u ( t e k c a r b t s 1 3 1 - 4 9 6 - c q x 2 y s s a r o s n e s t e g r a t b u s 4 0 1 - 4 9 6 - c q x 3 e t a l p t e g r a t 5 6 1 - 4 9 6 -...
Page 118
Page 118 34 35 33 36 37 38 41 42 40 43 44 42 39 45 46 55 56 54 53 51 52 49 54 47 48 50 flat target (upper) assembly - 2.
Page 119
Page 119 m e t i n o i t p i r c s e d o n t r a p 3 3 ) u ( e s a b 4 3 1 - 4 9 6 - c q x 4 3 r e p p o t s u 5 3 1 - 4 9 6 - c q x 5 3 r e b b u r r e p p o t s u 7 6 1 - 4 9 6 - c q x 6 3 t e k c a r b t n e m h c a t t a s e r i w d e h c n u b 9 3 1 - 4 9 6 - c q x 7 3 g o d r o s n e s 7 4 1 -...
Page 120
Page 120 a 12 32 31 30 29 14 28 23 25 24 21 13 20 22 19 18 12 13 9 14 17 16 9 8 13 15 12 9 11 9 5 7 6 1 2 3 9 10 4 27 13 26 flat target (lower) assembly - 1.
Page 121
Page 121 m e t i n o i t p i r c s e d o n t r a p ) y s s a t e g r a t b u s ( y s s a ) r e w o l ( t e g r a t t a l f h c e m - r a t - u - c q x 1 ) l ( t e k c a r b t s 1 8 1 - 4 9 6 - c q x 2 y s s a r o s n e s t e g r a t b u s 4 0 1 - 4 9 6 - c q x 3 e t a l p t e g r a t 5 6 1 - 4 9 6 -...
Page 122
Page 122 35 34 36 37 33 38 41 42 43 44 42 39 40 46 45 47 48 54 49 52 56 55 54 53 50 51 flat target (lower) assembly - 2.
Page 123
Page 123 m e t i n o i t p i r c s e d o n t r a p 3 3 ) l ( e s a b 4 8 1 - 4 9 6 - c q x 4 3 r e p p o t s u 5 3 1 - 4 9 6 - c q x 5 3 r e b b u r r e p p o t s u 7 6 1 - 4 9 6 - c q x 6 3 ) l ( t e k c a r b t n e m h c a t t a s e r i w d e h c n u b 1 9 1 - 4 9 6 - c q x 7 3 g o d r o s n e s 7...
Page 124
Page 124 2 1 2 4 5 6 15 13 14 5 5 6 3 12 7 12 8 9 5 11 10 17 18 18 16 19 shutter assembly.
Page 125
Page 125 m e t i n o i t p i r c s e d o n t r a p e t e l p m o c - y l b m e s s a r e t t u h s y s s a - t u h s - c q x 1 r e v o c t e g r a t n i a m 2 1 2 - 4 9 6 - c q x 2 t e k c a r b t n e m h c a t t a r e v o c 5 0 2 - 4 9 6 - c q x 3 2 t e k c a r b r e t t u h s 1 0 2 - 4 9 6 - c q x...
Page 126
Page 126 17 19 18 20 15 11 12 16 6 9 7 3 4 5 2 1 9 13 14 10 8 gun assembly.
Page 127
Page 127 m e t i n o i t p i r c s e d o n t r a p 1 ) l ( p i r g ) 2 m e ti f o t r a p ( - - - - - - - - - 2 n e e r g - ) l ( e d i s n u g 6 5 2 - 4 9 6 - c q x 3 n e e r g - t h g i s 4 5 2 - 4 9 6 - c q x 4 t e k c a r b t h g i s 6 1 0 - 4 9 6 - c q x 5 s n e l 5 1 0 - 4 9 6 - c q x 6 t e k ...
Page 128
Page 128 m e t i n o i t p i r c s e d o n t r a p 1 r e t e m l e n a p 2 0 0 0 0 0 5 6 2 d n u o w e r i w w 0 1 m h o 0 0 1 - r e t e m o i t n e t o p 4 6 1 0 0 0 6 7 b o n k d e t u l f 9 0 0 0 0 0 4 4 3 h c t i w s e d il s o c p d 3 2 0 0 0 0 0 6 4 h c t i w s h s u p o n p s 9 5 0 0 0 0 0 6 ...
Page 129
Page 129 10. Schematics.
Page 130
Page 130
Page 131: Brent Spares,
For all parts or technical support contact: brent spares, namco house, units 5-8, acton park estate, the vale, london. W3 7qe for technical support, warranty and advance replacement parts: [ +44 (0) 20 8324 6120 for consumable parts: [ +44 (0) 20 8324 6102 fax for both: +44 (0) 20 8324 6126.