- DL manuals
- NAMCO
- Arcade Game Machines
- Race on!
- Operator's Manual
NAMCO Race on! Operator's Manual
Summary of Race on!
Page 1
Operators manual i t is the responsibility of the operator to maintain customer safety at all times , and it is imperative that the details set out in this manual are followed precisely part no. 90500117 issue 1 ridge racer v.
Page 2: Contents
Page 2 contents operators manual ............................................................................................................................. 1 general safety considerations .................................................................................................. 4 allgemei...
Page 3
Page 3 8. Maintenance .................................................................................................................................. 56 8-1 error messages .......................................................................................................................... 58...
Page 4
Page 4 no part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without permission from namco europe limited. While the i...
Page 5
Page 5 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more removing and replacing parts adjustments or maintenance on this equipment should be carried out by suitably qualified personnel only. Do not make any alteration to this equipment w...
Page 6
Page 6 dieses dokument darf in keiner weise vervielfältigt werden. Jegliche tonaufnahmen sowie die speicherung auf datenträger (suchsysteme), die weitergabe oder sonstiges kopieren für den gewerblichen und privaten gebrauch sind untersagt und bedürfen der vorherigen genehmigung durch namco europe li...
Page 7
Page 7 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more hinweise zur aufstellung niemals das gerät einschalten bevor die aufstellung völlig abgeschlossen ist. Zur vermeidung von elektroschlägen muß das gerät mit einem ordnungsgemäß geer...
Page 8
Page 8 denne udgivelse må ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den må heller ikke lagres i et eftersøgningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra namco europe limited...
Page 9
Page 9 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more punkter om installation tænd aldrig for strømmen til maskinen før installering er fuldført. For at undgå mulige elektriske stød sikres, at maskinen er forbundet til hovedstrømmen m...
Page 10
Page 10 no se permite la reproducción total ni parcial de esta publicación por ningún medio mecánico, fotográfico o electrónico, grabaciones fonográficas, ni su almacenamiento informático, su transmisión o su copia, ya sea para uso público o privado, sin permiso de namco europe limited. Si bien la i...
Page 11
Page 11 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more retirar y reemplazar partes y unidades . Las revisiones de instalación, los ajustes, y el mantenimiento rutinario deberán llevarse a cabo sólo por personal cualificado. No realice...
Page 12
Page 12 aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen denregistement phonographique. Ces informations ne seront ni stockées grâce à un procédé de récupération, ni transmises ou autrement copiées pour un usage publique...
Page 13
Page 13 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more notes dinstallation ne jamais mettre le jeu en marche avant que linstallation ne soit complétement effectuée. Afin de prévenir une éventuelle électrocution, sassurer que la mac...
Page 14
Page 14 Κανένα μέρος αυτής της έκδοσης δεν μπορεί να αναπαραχθεί με οποιοδήποτε μηχανικ" ,φωτογραφικ" ή ηλεκτρονικ" μέσο , ή με μορφή φωνητικής ηχογράφησης και ούτε να αποθηκευτεί με επανορθωτικ" σύστημα , να μεταδοθεί ή να αντιγραφεί για δημ"σια ή ιδιωτική χρήση , χωρίς την άδεια της namco europe l...
Page 15
Page 15 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more ΑΠΟΜΑΚΡΥΝΣΗ ΚΑΙ ΑΝΤΙΚΑΤΑΣΤΑΣΗ ΜΕΡΩΝ - ΑΝΤΑΛΛΑΚΤΙΚΩΝ Εγκατ%σταση , μετατροπ# # λεγχος ρουτνας μπορε να γνεται μνο απ εξουσιοδοτημνα %τομα . Δεν πρπει να γνονται μετατροπς στα μηχαν...
Page 16
Page 16 nessuna parte di questa pubblicazione può essere riprodotta con processo meccanico, fotografico o lettronico, nè sotto forma di registrazione fonografica, nò può essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza lautorizzazi...
Page 17
Page 17 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more notes dinstallation non accendere mai la macchina finchè linstallazione non è stata completata. Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbl...
Page 18
Page 18 ingen del av denne utgivelsen må reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra namco europe limited. Da in...
Page 19
Page 19 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more fjerne og utskifte enheter og deler. Installasjon, service, justering eller rutine vedlikehold skal bare utføres av kvalifiserte personer. Ikke lag noen forandringer på denne mask...
Page 20
Page 20 niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toest...
Page 21
Page 21 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more verwijderen en vervangen van assemblies en onderdelen installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen. Maak ...
Page 22
Page 22 nenhuma parte desta publicacão poderá ser reproduzida por processos mecanográficos, fotográficos, electrónicos ou ainda sob a forma de gravacão sonora nem tão pouco poderá ser gravada através de sistemas informáticos transmissiveis ou de outra forma copiados para uso publico ou privado sem a...
Page 23
Page 23 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more substituiÇÃo e montagem de peÇas a montagem, assistência e afinações ou manutenção de rotina desta maquina, deverão ser somente executadas por tecnicos ou pessoas devidamente qual...
Page 24
Page 24 ingen del av denna publikation får reproduceras, varken fotografiskt, elektroniskt eller i någon form av ljudinspelning. Det får inte heller lagras i något återvinningssystem, översändas eller på annat sätt kopieras för offentlig eller privat användning, utan tillstånd från namco europe limi...
Page 25
Page 25 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more att beakta vid installation sätt aldrig på strömmen på maskinen innan installationen är klar. För att förhindra elektriska chocker, försäkra dig om att maskinen kopplas till ström...
Page 26
Page 26 tästä julkaisusta ei saa ottaa missään muodossa kopioita yksityis- tai julkiseen käyttöön ilman namco europe limited :in lupaa. Tässä ohjekirjassa olevat tiedot pitävät julkaisuhetkellä paikkansa. Namco europe limited:illä on kuitenkin oikeus muutoksiin ilman erillistä ilmoitusta. Tämä laite...
Page 27
Page 27 50cm or more 50cm or more play zone pathway 2m 20cm or more 30cm or more 30cm or more 2m 20cm or more 1m or more asennushuomioita Älä koskaan kytke laitetta päälle ennen kuin asennus on suoritettu loppuun. Tämän laitteen virtalähde on kytkettävä maadoitetulla johdolla maadoitettuun pistorasi...
Page 28
Page 28 1. Specifications power supply:- 230v /350watts ac ambient operating +5°c to +25°c temperature monitor:- hantarex 28 polo-medium planar (type 02193240) coin acceptor:- mars cashflow - 4 channel dispense dimensions:- assembled 1600(w) x 1630(w) x 1990(h) monitor cabinet 1600(w) x 870(d) x 15...
Page 29
Page 29 2. How to play this is a multi-play car racing game, which can be played by one or two people. The player(s) compete against computer cars. [game overview] the object of the game is to complete a specified number of laps in the given time period. Extra time is awarded at specified points of ...
Page 30
Page 30 3. Major components seat assy seat assy coin assy accelerator pedal assy brake pedal assy steering assy control panel assy control panel assy monitor game pcb assy game pcb assy mains-in and on / off switch header assy fluorescent lamp.
Page 31
Page 31 5. Installation notes on installation warning never turn the power to the machine on until installation has been completed. Warning in order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug. Warning so that custome...
Page 32
Page 32 쮕 denne maskine er kun designet til indendØrsbrug installer ikke maskinen pÅ fØlgende steder 1. Udendørs 2. Direkte sollys, steder med høj fugtighed el. Støv, steder med vand udslip, i nærheden af air-condition eller varme udstyr, steder med usædvanlig høj el. Kold temperatur. 3. Steder hvor...
Page 33
Page 33 ও denne maskinen er bare konstruert for innendØrs bruk ikke installer maskinen pÅ fØlgende plasser. 1. Utendørs 2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje, nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur. 3....
Page 34
Page 34 denna maskin Är avsedd enbart fÖr inomhusbruk installera ej maskinen pÅ fÖljande stÄllen 1. Utomhus 2. I direkt solsken, platser med extremt hög luftfuktighet eller damm, platser där det förekommer vattenläckage, nära luftkonditionering eller värmeelement, i extremt hög eller låg temperatur....
Page 35
Page 35 5-2 fitting the header assembly the header assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the header assembly. The fitting position of the header assembly is very high, and it is important that a means of reaching the height sa...
Page 36
Page 36 5. Fit the 3off pozi head screw, with flat and spring washer, (m6x16) to retain the header assembly in position. Pozi head screw (with flat/spring washers) (m6 x 16) header assy.
Page 37
Page 37 5-3 fitting the seat assemblies 1. Remove 10off security screw (m5x16) and remove both floor plates. 2. Place the seat assemblies up to the monitor cabinet and set the adjustable feet so that the seat base is level with the main cabinet. 3. Connect the connectors. 4. Fit the 8off hex head sc...
Page 38
Page 38 5-4 adjusting the level adjusters 1. When the assembled game is in its final position, lower the twelve (12) level adjusters,(4off monitor assy and 4off each seat assy), with a spanner so that the machine is level and all castors are raised from the floor by approx. 5mm. Tighten the lock nut...
Page 39
Page 39 5-6 fitting the game pcb security cards the security cards are designed for this game only. Do not use them with other models. Do not insert any other security cards. These may result in malfunctions. Always turn off the power before inserting the security cards. Always install one security ...
Page 40
Page 40 5-7 fitting the cd rom the supplied cd-roms are designed for this game only. Do not use them with othergames. Do not insert any other cd-roms. These may result in malfunction. Always install one cd-rom to each game pcb assy. Note that the tray automatically closes after approximately 10 seco...
Page 41
Page 41 6. Adjustments 6-1 turning on the power after the machine has been installed, turn on the power. The power switch is located on the rear of the monitor cabinet. Adjustment or maintenance on this machine should be carried out by qualified personnel only. Einstellungen und wartung des gerätes ...
Page 42
Page 42 6-2 adjustment switches the adjustment switches are located inside the coin door. 1. Service switch. Press this switch to obtain game credits without incrementing the play meter. 2. Test switch slide the test switch on to enter test mode. Test mode allows testing and the changing of game set...
Page 43
Page 43 6-3 test mode 1. Open the coin door and slide the test switch on. The menu screen will be displayed on the monitor. 2. Select the test required by using the select up/down switch. The colour of the selected test will change. 3. Activate the test by pressing the enter switch. Select exit...
Page 44
Page 44 6-3-1 coin options 1. Select coin options on the menu screen to set the game cost and related settings. The following screen is displayed. 2. Use the select up/down switch choose the required item then press the enter button. 3. Use the select up/down switch to change the setting. 4. Press...
Page 45
Page 45 6-3-2 game options 1. Select game options on the menu screen to set the game variables, the following screen is displayed. 2. Use the select up/down switch to choose the required item then press the enter button. 3. Use the select up/down switch to change the setting. 4. Press the enter bu...
Page 46
Page 46 m e t i n o i t p i r c s e d t e s - e r p d i b c p ) a ( ) t h g i r ( 2 , ) t f e l ( 1 d i b c p e m a g s t e s 2 r e b m u n s i t a e s t h g i r e h t d n a 1 r e b m u n s i t a e s t f e l e h t t i a w y r t n e ) b ( r e t n e o t r e y a l p d n o c e s r o f s t i a w e m a g ...
Page 47
Page 47 6-3-3 i/o test 1. Select i/o test on the menu screen to test the switches and lamps. The following screen is displayed. 2. Use the select up/down switch to choose the required item then press the enter button to enter the test. 3. Select exit and press the enter button to return to the m...
Page 48
Page 48 6-3-3-1 i/o pcb test 1. Select i/o pcb check from the i/o test screen. The following screen is displayed:- note: this screen is for information only. No adjustments are available. 6-3-3-2 go to [i/f initialize] this item initializes the control devices. Selecting this option displays the i...
Page 49
Page 49 6-3-3-3 switch test 1. Select switch test on the i/o menu screen to test the switches. The following screen is displayed. 2. The display shows the current state of the switches. 3. Press the up select switch and the enter switch together to exit and return to the i/o menu screen (a) not us...
Page 50
Page 50 6-3-3-4 lamp test 1. Select lamp test from the i/o test screen. The following screen is displayed:- (a) the view change lamp will turn on or off each time the enter switch is pressed, and the display will change from off to on. I / o test dip sw 1234 [on : red] link on link as 1 (left) lam...
Page 51
Page 51 6-3-4 monitor test 1. Select monitor test on the menu screen to test and adjust the monitor. The following screen is displayed. 2. Use the select up/down switch to choose the required item then press the enter button. To return to the monitor test menu from a test pattern press the enter b...
Page 52
Page 52 6-3-5 sound test 1. Select sound test on the menu screen to test the audio and adjust the volume settings. The following screen is displayed. 2. Use the select up/down switch to choose the required item then press the enter button. 3. Use the up/down switch to change the setting. 4. Press ...
Page 53
Page 53 6-3-6 cd test 1. Select cd test on the menu screen to test the cd read-in. The following screen is displayed. 2. Use the select up/down switch to choose the required item then press the enter button to enter the test. 3. Select exit and press the enter button to return to the menu screen...
Page 54
Page 54 6-3-7 ads data by selecting ads data from the menu screen, all of the bookkeeping details can be read and/or reset. 6-3-8 others 1. Select others on the menu screen. The following screen is displayed. 2. Use the select up/down switch choose the required item then press the enter button. 3....
Page 55
Page 55 7. Initialization adjustments when replacing parts the following operation must always be performed after replacing the game pcb, rom, or control potentiometers. The game will not operate correctly if these adjustments are not made. 1. Slide the test switch on while pressing the service swit...
Page 56
Page 56 8. Maintenance adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the power to the machine is turned off before commencing any maintenance work. (trouble shooting, service or repairs etc.) einstellungen und wartung des gerätes dürfen nur ...
Page 57
Page 57 aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine uitgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.) afinações ou manutenção nesta maquina, deverão ser efectuadas sóme...
Page 58
Page 58 8-1 error messages the machine automatically executes a self-test when the power is turned on. If the machine is normal, the startup screen appears on the monitor. If there is something wrong, the machine beeps or displays an error message on the monitor, and stops operation. See below for e...
Page 59
Page 59 8-2 replacing the cd rom drive ensure that the power to the game is turned off before starting work. 1. Remove the monitor cabinet lower rear door. 2. Remove the cd rom and place the cd rom in a safe place. (see 5-7 page 40) 3. Disconnect the 7 connectors (shaded) as shown below. 4. Remove t...
Page 60
Page 60 5. Disconnect the three connectors as shown shaded in the figure below. 6. Remove 1off pozi head screw (m4x10), with flat and spring washer, and remove the cd drive in the direction of the arrow, as shown below, taking care not to bend the hook on the rear of the drive. 7. Remove 4off pozi h...
Page 61
Page 61 8-3 replacing the steering pcb and/or fuse 1. Remove 8off button head screws (m5x12) and remove the monitor cabinet rear cover. 2. Replace the fuse or: 3. Disconnect the six connectors shown shaded in the diagram below. 4. Loosen 2off pozi head screws (m6), lift the pcb base to disengage it ...
Page 62
Page 62 8-4 repacing the amplifier pcb 1. Remove the floor plates. (see 5-3 page 37) 2. Disconnect the connectors shown shaded in the diagram below. 3. To remove the amplifier pcb from the locking supports, squeeze the tabs of the support together and gently lift the pcb upwards. Repeat for each sup...
Page 63
Page 63 8-5 replacing the fluorescent lamp or starter. 1. Remove 3off button head screws (m5x12) and remove the top retaining bracket. 2. Remove the header acrylic. 3. Replace the fluorescent tube or starter. 4. Reassemble in reverse order. Header acrylic top retaining bracket button head screw (m5 ...
Page 64
Page 64 8-6 replacing the gear shift assy 1. Remove 4off security screws (m6x16). 2. Lift the gear shift assembly only sufficient to disconnect the connector. 3. Remove the gear shift assy. 4. Reassemble in reverse order. Security screw (m6 x 16) gear shift assy connector.
Page 65
Page 65 8-6-1 replacing the gear shift microswitch 1. Remove the gear shift assy. (see 8-6 page 64) 2. Disconnect the fast-on connectors. 3. Remove 2off pozi head screws and remove the microswitch. 4. Reassemble in reverse order. Microswitch pozi head screw (m3x16).
Page 66
Page 66 8-7 removing the play panel assy 1. Remove the gear shifter assy. 2. Remove 6off security screw (m5x20) and lift the play panel only sufficient to access the connector. 3. Disconnect the connector and lift the play panel assy away. 4. Reassemble in reverse order. Control panel assy security ...
Page 67
Page 67 8-8 replacing the view change/credit available switches 1. Remove the play panel assy. (see 8-7 page 66) 2. Remove the switch/lamp assembly by pulling it out from the switch body. 4. Replace the switch or lamp. 5. Reassemble in reverse order. View change switch control panel assy view change...
Page 68
Page 68 8-9 replacing the steeering assembly 1. Remove the play panel assy. (see 8-7 page 66) 2. Disconnect the steering motor and steering potentiometer connectors. 3. Remove 4off hex head screws (m8x25) and remove the steering assembly. 4. Reassemble in reverse order hex head screw (m8x25) hex hea...
Page 69
Page 69 8-10 replacing the steering potentiometer 1. Remove the steering assembly. (see 8-9 page 68) 2. Remove 2off hex socket head screws (m4x10) holding the potentiometer mounting bracket to the front plate. 3. Slacken the grub screw (m4x10) and remove the potentiometer complete with the mounting ...
Page 70
Page 70 8-11 replacing the drive belt 1. Remove the steering assembly. (see 8-9 page 68) 2. Slacken the adjustment screw (hex head m6x60). 3. Slacken the 4off hex nuts to remove the tension from the belt. 4. Replace the drive belt. 5. Tighten the adjustment screw (m6x60) to tension the belt correctl...
Page 71
Page 71 8-12 removing the steering wheel 1. Remove 3off countersunk socket head screws and remove the centre cap. 2. Remove 3off countersunk socket head screws and remove the steering wheel. Note: when replacing the steering wheel ensure that the steering wheel shaft is in the centre position and th...
Page 72
Page 72 button head screw (m5 x 12) brake pedal assy accelerator pedal assy pedal plate connectors 8-13 removing the pedal assy 1. Remove 4off button head screws (m5x20). 2. Withdraw the pedal assembly only sufficiently to disconnect the connectors. 3 remove the pedal assembly. 4. Reassemble in reve...
Page 73
Page 73 8-14 replacing the pedal potentiometer 1. Remove the pedal asembly. (see 8-13 page 72) 2. Slacken the hex socket screw (m4x8) and remove the potentiometer complete with potentiometer bracket. 3. Replace the potentiometer ensuring that the correct colour wires go to the correct terminals. Not...
Page 74
Page 74 8-15 replacing the brake damper 1. Remove the pedal assemble. (see 8-13 page 72) 2. Remove 4off flange socket head screws (m6x8) and remove the brake damper assy. 3. Replace the damper assy and reassemble in reverse order. Note: after replacing the damper ensure that the game is re-initializ...
Page 75
Page 75 8-16 replacing the pedal stop rubber 1. Remove the pedal assembly. (see 8-13 page72) 2. Remove the countersunk washer nut and hex head screw (m6x60). 3. Replace the stop rubber. 4. Reassemble in reverse order. Note: after replacing the damper ensure that the game is re-initialized. (see sect...
Page 76
Page 76 8-17 replacing the monitor the power to the game must be switched off before removing the monitor. The monitor is heavy. Ensure that at least two people are available to remove the monitor, and ensure that there is sufficient space to work safely. 1. Remove the monitor cabinet rear cover (se...
Page 77
Page 77 monitor face ctr security screw (m5 x 20) security screw (m5 x 20) 5. Remove 6off security screw (m5x20) and remove the monitor face ctr. 6. Remove 5off security screw (m5x20) and remove the monitor face upr, monitor face and monitor mask as one assembly. Monitor face l monitor face r monito...
Page 78
Page 78 7. Remove 4offpozi head screws (m5x12) and remove the top bracket. 8. Remove 2off pozi head screw(m5x12) and remove the mask bracket. Top bracket pozi head screw (m5 x 12) mask bracket pozi head screw (m5 x 12).
Page 79
Page 79 9. Remove 4off pozi head screws (m8x20), with flat and spring washers, holding the monitor in place. 10. Slowly tilt the monitor forward and then lift the monitor out from the front. 11. Reassemble in reverse order. Washer (m8) monitor washer (m8) pozi head screw (m8x20) (with flat/spring wa...
Page 80
Page 80 9. Parts 9-1 monitor cabinet 3 01 192 18 22 cross section c-c c c 20 12 1 2 10 9 opposite side 11 opposite side 14 13 opposite side 8 7 6 5 4 15 3 cross section b-b b b.
Page 81
Page 81 m e t i n o i t p i r c s e d o n t r a p 1 ) 0 0 4 2 3 9 1 2 0 e p y t ( a n a l p m u i d e m " 8 2 o l o p x e r a t n a h - r o t i n o m 1 0 0 0 0 0 4 8 2 s h r - r a ll i p e d i s 0 4 3 0 0 0 7 4 3 5 9 x 6 1 m - t o o f e l b a t s u j d a 9 7 0 0 0 3 8 8 4 m m 5 7 - r o t s a c l e v...
Page 82
Page 82 9-2 header assy 2 4 5 7 8 1 6 3 opposite side m e t i n o i t p i r c s e d o n t r a p 1 c il y r c a r e d a e h 1 6 0 0 0 0 0 3 2 s h l - m r o f - c a v r e d a e h 1 3 3 0 0 0 7 4 3 s h r - m r o f - c a v r e d a e h 2 3 3 0 0 0 7 4 4 s h l - d o o w e d i s r e d a e h 8 4 0 0 0 0 7 3...
Page 83
Page 83 9-3 mains-in assy and service bracket 7 6 8 1 2 3 4 5 m e t i n o i t p i r c s e d o n t r a p 1 r e t e m t n u o m l e n a p 2 0 0 0 0 0 5 6 2 r e d l o h e s u f t n u o m l e n a p 6 8 7 0 0 5 3 6 b / q a 2 m m 0 2 e s u f 1 0 5 0 0 5 3 6 3 h c t i w s e d il s e r u t a i n i m 3 2 0 0...
Page 84
Page 84 9-4 play panel assy 1 3 2 4 5 m e t i n o i t p i r c s e d o n t r a p 1 m r o f - c a v g n i r e e t s 9 5 3 0 0 0 7 4 2 l a c e d m r o f - c a v 1 2 6 0 0 0 4 3 l a c e d e l b a li a v a t i d e r c / e g n a h c w e i v 8 9 3 0 0 0 4 4 y s s a n o t t u b h s u p e g n a h c w e i v 4...
Page 85
Page 85 9-5 steering assy 1 7 6 3 4 5 2 m e t i n o i t p i r c s e d o n t r a p e t e l p m o c - y s s a g n i r e e t s 4 3 0 0 0 8 8 8 1 l e e h w g n i r e e t s 3 0 0 0 0 5 1 8 2 s s o b l e e h w g n i r e e t s 4 0 0 0 0 5 1 8 3 r o t o m g n i r e e t s 0 4 0 0 0 8 8 8 4 r e t e m o i t n ...
Page 86
Page 86 9-6 shifter assy m e t i n o i t p i r c s e d o n t r a p e t e l p m o c - y s s a f f o e r t n e c r e t f i h s w o l - i h 9 0 0 0 0 8 8 8.
Page 87
Page 87 9-7 accelerator pedal assy 7 8 4 9 3 cross section a-a 6 6 a a m e t i n o i t p i r c s e d o n t r a p e t e l p m o c - y s s a l a d e p r o t a r e l e c c a l a d e p - a - 5 r x x 3 l a d e p 3 2 0 - 3 6 4 x 4 t f a h s 5 2 0 - 3 6 4 x 6 n o i h s u c 7 0 0 - 2 6 4 x 7 a g n i r p s 9...
Page 88
Page 88 9-8 brake pedal assy 8 4 9 3 cross section a-a 7 6 7 a a m e t i n o i t p i r c s e d o n t r a p e t e l p m o c - y s s a l a d e p e k a r b l a d e p - b - 5 r r x 3 l a d e p 4 2 0 - 3 6 4 x 4 t f a h s 5 2 0 - 3 6 4 x 6 r e p m a d e k a r b 8 2 0 - 3 6 4 x 7 n o i h s u c 7 0 0 - 2 6...
Page 89
Page 89 9-9 game pcb assy 3 1 2 m e t i n o i t p i r c s e d o n t r a p 1 y s s a b c p e m a g b c p e m a g - 5 r r x 2 m o r - d c m o r d c - 5 r r x 3 v 0 3 2 n a f " ½ 4 5 1 0 0 0 0 7 6 d r a u g r e g n i f 9 6 1 0 0 0 9 3.
Page 90
Page 90 9-10 seat assy 10 12 7 3 11 6 9 13 14 m e t i n o i t p i r c s e d o n t r a p 3 e t a l p r e v o c r o o l f 2 6 3 0 0 0 7 4 6 l a c e d r a e r t a e s 2 2 6 0 0 0 0 4 7 m s i n a h c e m g n i d il s t a e s 0 8 6 0 0 3 8 8 9 s t u o t u c r e k a e p s h t i w - d e r - s t a e s d e d...
Page 91
A21 b18 a27 b26 b1 b24 b21 a22 b23 b30 a7 a3 b27 a24 a11 b11 a18 b17 a17 a1 a30 3 2 1 3 2 1 9 10 11 12 9 10 11 12 1 2 1 2 1 2 3 4 1 2 3 4 h.D. 'd' connector 15w ieee1394 amp ei 3w amp mini 12w amp mini 2w ps60p v257 bass amp pcb assy (l) ps 2 game pcb assy (l) 1 2 3 1 2 3 amp univ 3w amp univ 4w 1 2...
Page 92
For all parts or technical support contact: brent spares, namco house, units 5-8, acton park estate, the vale, london. W3 7qe www.Namco.Co.Uk for technical support, warranty and advance replacement parts:- +44 (0) 20 8324 6120 for consumable parts:- +44 (0) 20 8324 6102 fax for both:- +44 (0) 20 832...