1. DL manuals
  2. NAMCO
  3. Board Game
  4. TEKKEN 4
  5. Operation Manual

NAMCO TEKKEN 4 Operation Manual

Manual is about: Game PC Board Kit

Summary of TEKKEN 4

  • Page 1

    Tekken 4 game pc board kit l ensure safe operation of product, be to read this manual before use. L keep this operation manual in a safe place for quick access. Namco america inc.

  • Page 2

    Read precautions and installation sections before operating game note: this equipment uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a reside...

  • Page 3: Introduction

    Introduction thank you for purchasing the tekken 4 game pc board kit (hereafter referred to as “the product”). This operation manual describes: how to operate the product correctly and make full use of its features how to conduct the following procedures safely installation and connection of the pro...

  • Page 4

    Dear customers, july,2001 thank you for purchasing the tekken 4 pcb kit. This notice to inform you that the dongle in this kit is not installed in the pcb rack assy. Please follow the following instructions make sure that the dongles are fitted properly to the pcb. Best regards dongle adjustments-to...

  • Page 5: Safety Precautions.

    Safety precautions. Be to read these instructions to ensure instructions to the owner: l if you entrust another party to perform installation, connection, adjustment, operation, inspec- tion, cleaning, troubleshooting, removal, storage, transportation or disposal of the product, in- struct the conce...

  • Page 6

    Safety precautions be to read these instructions to ensure safety top-priority safety precautions 1-3-i general precautions do not disassemble or modify the product. Also never perform work not described in this operation manual. Failure to observe this caution can result in an electrical shock or f...

  • Page 7

    1. Safety precautions be to read these instructions to ensure safety. I - 3 - 3 c a u t i o n s i n o p e r a t i o n l should any problem occur, such as an abnormal odor or noise, turn off the power switch on the cabinet immediately to stop the machine operation. Then, unplug the power cord from th...

  • Page 8: Contents

    Contents i n t r o d u c t i o n 1. Precautions be sure to read these instructions to ensure safety ............................ 1 l - l magnitudes of risk ......................................................................................................................................... 1 l-2 ...

  • Page 9

    Contents display test (checking and adjusting screen display) 32 6-2-l common procedures .......................................................................................................................... 33 6-2-2 convergence (checking and adjusting display size, display position, aspect rati...

  • Page 10: 2. Specifications

    2. Specifications item compatibility weight input power operating environ- ment connectable cabinet monitor orientation and monitor signal l i n k e d s e t u p control panel of c a b i n e t m e t h o d o f i n s t a l l a t i o n i n c a b i n e t standard pc board kit (optional) is required) vide...

  • Page 11

    3. Checking the package content the product package contains the following parts when l check to make sure all parts listed below are included in the product p a c k a g e . L any parts are missing, contact your distributor. Keep the box. The box is used to send the product for a repair. N a i p / n...

  • Page 12: 4. Names of Parts

    4. Names of parts d v d - r o m drive connector video cable connectors audio cable connectors standard cable connector b o a r d pc.

  • Page 13

    5. Installation and connection be conducted bv a technician before installing and connecting the product, turn off the power switch on the cabinet and unplug the power cord from the service outlet to prevent an electric shock. L do not install or connect the product outdoors. The product is designed...

  • Page 14: Preparation For Installation

    5. Installation and connection be conducted by a technician only preparation for installation prepare the following tools and materials for the installation of the product. Item to be prepared operation manual of the cabinet soldering iron, or crimping tool and crimp-style termi- nals heat-shrink in...

  • Page 15: Pc Board to Mount-

    5. Installation and connection be conducted by a technician only 5-2 installation of pc board and pc board to mount- ing plate of standard conforming cabinet to install the product in a standard conforming cabinet, mount the pc board and (b) pc board on the mounting plate by following the procedures...

  • Page 16

    5. Installation and connection be conducted by a technician only. Q using the supplied mounting screws (phillips tapping bind (a) x install the pc board and pc board at locations on the mounting plate where the installed pc boards do not hinder the reinstallation of the mounting‘plate. Mounting hole...

  • Page 17: Video

    5. Installation and connection be conducted by a technician only 5-3 installation of pc board to mounting plate of video standard (jvs) conforming cabinet q install the pc board to the mounting plate by following the procedures below. Turn off the power switch on the cabinet, and unplug the power co...

  • Page 18

    5. Installation and connection he conducted by a technician only using the supplied mounting screws (phillips tapping bind (a) x install the pc board at a location on the mounting plate where the installed pc board does not hinder the reinstallation of the mounting plate. Mounting holes (4 locations...

  • Page 19: 5-4 Connection to

    5. Installation and connection to be conducted by a technician only. 5-4 connection to standard conforming cabinet 5-4-l checking the edge connector to connect the product to a standard conforming cabinet, use the edge connector provided with the cabinet. Check to make sure the terminal numbers of t...

  • Page 20

    5. Installation and connection. To be conducted by a technician check the voltage of power supplied from the cabinet to be connected with the edge connector and the voltage of power supplied to the coin counter in the cabinet. The power supplied from the cabinet connected to the edge connector must ...

  • Page 21

    5. Installation and connection be conducted by a technician only connecting to the control panel the product is designed to connect to a control panel (see the diagram below) that complies with the specifications listed in “2. 6). Start switch p2 i-direction lever button switches p2 button switches ...

  • Page 22

    5. Installation and connection. To be conducted by a technician only connect the following wires of the extension switch harness to the terminals of pi button switches and p2 buttons switches using a soldering iron or style terminals. Extension switch harness terminal no. Signal name (wire color) (b...

  • Page 23

    5. Installation and connection to he conducted by a technician only. Connecting the speaker connect the product to the speakers in the cabinet for sound reproduction. First, check if the cabinet has monaural speakers or stereo speakers. L monaural speakers turn off the power switch on the cabinet, a...

  • Page 24

    5. Installation and connection be conducted by a technician only. Connecting the connector turn off the power switch on the cabinet, and unplug the power cord from the service outlet. Connect the edge connector, extension switch harness and extension ste- reo harness to the pc board. When connecting...

  • Page 25

    5. Installation an0 connection be conducted by a technician only. Install the mounting plate attached with the pc board in the cabinet l make sure the mounting plate is securely installed in the cabinet. If it is loose, the pc board can malfunction due to vibrations. L after installing the mounting ...

  • Page 26: Connection to

    5. Installation and connection to be conducted by a technician only. Connection to standard conforming cabinet the following describes the method of connecting the pc board to a video standard (jvs) conforming cabinet. First, follow the directions in “5-3 board to mounting plate of video standard (j...

  • Page 27

    5. Installation and connection to be conducted by a technician only turn off the power switch on the cabinet, and unplug the power cord from the service outlet. If the control panel is different from the one shown on the previous page, replace the control panel by following the directions in the ope...

  • Page 28

    5. Installation and connection be conducted by a technician only connect the cables of the cabinet to the appropriate connectors of the pc board, as shown below. Power supply harness (provided with the product) , video cable can be connected to either connector. When there are video cables, connect ...

  • Page 29: 5-6 Inserting Dvd-Rom

    5. Installation and connection. To be conducted by technician only 5-6 inserting dvd-rom l the dvd-rom must be inserted with the power switch turned on. To prevent an electrical shock, accident and injury, do not touch sections other than those specified in the work procedures. The supplied dvd-rom ...

  • Page 30

    5. Installation and connection be conducted by a technician only with the label side (printed surface) of the dvd-rom facing away from the tray, set the dvd-rom on the tray. Dvd-rom make sure the dvd-rom is securely placed on the tray, with the label side facing away from tray. Press eject button of...

  • Page 31: 5-7 Attaching Stickers

    5. Installation and connection to be conducted by a technician only 5-7 attaching stickers affix the supplied stickers on the cabinet, and set up the machine. Caution sticker for strong title lighting sensitivity(c) sticker b button sticker r namco cyberlead (example).

  • Page 32: 6. Adjustment For Operation

    6. Adjustment for operation before operating the tekken 4 game machine, adjustments must be made according to the type of the cabinet used. The following shows the items to be adjusted. Adjustment item section and page i check and adjustment of screen display testing of switches connected to pc boar...

  • Page 33

    6-1-i adjustment switches and knob the pc board is provided with option switches ((1) in the diagram). When the connection kit is installed, a speaker volume knob ((2) in the diagram) is also provided. (1) option switches four switches are provided as a set. Switch 1 is used to change between test m...

  • Page 34

    6. Adjustment for operation 6 - i - 2 s e l e c t i o n o f a d j u s t m e n t i t e m to make adjustments, display the test menu screen using the test mode function. Turn on the power switch on the to display the game screen. Set option switch or the test switch of the cabinet to on. The test mode...

  • Page 35

    6. Adjustment for operation (p. 32) to “6-9 data clear” 46). By moving the &direction lever up or down, select an adjustment item (from 2 display test” (p. 32) to data clear” 46)) on the screen (selected item turns red). Pi &direction lever 8 (note) the above diagram shows a pair control panel. For ...

  • Page 36

    6. Adjustment for operation 6-i-3 exiting from test mode making each adjustment according to the procedures described from “6-2 display test” 32) to data clear” (p. Display the test menu screen. Move the i-direction lever up or down and turn the “exit save” indication red. Press the pi button switch...

  • Page 37

    6. Adjustment for operation before checking or adjusting, first conduct the following common procedure. 6-2-l common procedures follow in selection of adjustment item” 30 and 31). In , select “display test. On the screen, the color edit screen appears on top of the color bar screen, as shown below. ...

  • Page 38

    6. Adjustment for operation press the button switch 1 to move to another adjustment item. L every time the button is pressed, the mode and screen change in the following order: color convergence interlace check button switch 1 pi start switch button switch 3 (note) the above diagram shows a pair con...

  • Page 39

    6. Adjustment for operation 6-2-3 color edit, color bar (adjusting contrast and color of video sig- nal output from pc board) follow steps ‘6-2-l common procedures” 33) to display the color edit screen on the color bar screen. L if the display test screen is already displayed, skip the in common pro...

  • Page 40

    6. Adjustment for operation by moving the a-direction lever up or down, select an adjustment item from “contrast,” “bright r,” “bright and “bright b.” pi lever pi button switch 1 i pi button 3 pi button switch 4 (note) the above diagram shows a pair control panel. For a single control panel (when tw...

  • Page 41

    6. Adjustment for operation 6-2-4 interlace check (switching between interlace and non-interlace modes) ‘only when monitor’s horizontal synchronization frequency is 15.75 interlace mode: this mode provides more detailed and smoother graphics than the non-interlace mode. By shifting the picture displ...

  • Page 42

    6 . A d j u s t m e n t for operation display test : : interlace mode make sure “interlace” is displayed at the upper right corner of the screen l if “non interface” is shown, set to “interlace” by following the procedures below. (1) move the &direction lever up or down and select “non interlace” at...

  • Page 43

    6. Adjustment for operation press the pi start switch to exit from the display test and return to the test menu screen. The test menu screen (p. 30) appears. To make other adjustments in the display test, press the button switch 1 and display the adjustment screen. To exit from the test mode, follow...

  • Page 44

    6. Adjustment for operation l if the screen indications do not change according to the lever/button operations, the game cannot be played properly. When it happens, refer to p. 52 troubleshooting.” to return to the test menu screen, press the pi sutton switches and 2 simulta- neously. (note) the abo...

  • Page 45: Video Stan-

    6. Adjustment for operation operate the lever or switch according to the test and adjustment item shown in the following table, and make the adjustment. Item sound output test monaural/stereo setting test/adjustment operation reproduction of test sound when pi button switch 1 is pressed, sound i pro...

  • Page 46

    6. Adjustment for operation 6-6 game options (setting the game options) this screen is used to set the game options such as the game level. Follow steps “6-1-z selection of adjustment item” 30 and 31). In step select “game options.” the following screen will appear i game defaults in green difficult...

  • Page 47

    6. Adjustment for operation (a) difficulty level (degree of game difficulty) easy medium hard v e r y h a r d u l t r a (b) fight count 1 p game (number of rounds required to win the game in mode) 2 3 4 5 (c) fight count vs game (number of rounds required lo win game in competition mode) 2 (d) life ...

  • Page 48

    6. Adjustment for operation 6-7 coin options (setting the game pricing) this screen is used to set the game pricing such as credits for one game play. Follow steps “6-l-2 selection of adjustment item” 30 and 31). In step , select “coin options.” the following screen appears coin defaults in green st...

  • Page 49

    Adjustment for operation (c) coin chute 1 mechanical value (number of coins added per one operation of coin switch 1) 1 coin count as 1 2 3 4 5 6 7 8 9 coin (d) coin chute mechanical value (number of coins added per one operation of coin switch 2) 1 coin count as 1 2 3 4 5 6 7 8 9 coin (e) credit mo...

  • Page 50

    6. Adjustment for operation to return to the test menu, press the pi start switch. Start switch (note) the above diagram shows a pair control panel. For a single control panel (when two jammavideo standard (jvs) conforming cabinet cabinets are connected for communication-linked setup), the cabinet i...

  • Page 51

    6. Adjustment for operation the following screen appears. Data clear a.D.S. Data ranking data clear set defaults all options all dear clear: pl-button1 exit : pl-start to test menu screen game data only ranting data all options to deletes all stored data. Display of method to execute item display of...

  • Page 52

    6. Adjustment for operation to execute the selected item, press the button switch 1 (note) the above diagram shows a pair control panel. For a single control panel (when two jammavideo standard (jvs) conforming cabinet cabinets are connected for communication-linked setup), the cabinet installed wit...

  • Page 53: 7. Operation

    7. Operation should any problem occur, such as an abnormal odor or noise, turn off the power switch on the cabinet immediately and stop the machine operation. Then, unplug the power cord of the cabinet from the service outlet, and contact your distributor. Operating the machinewith a problem left un...

  • Page 54: 7-3 Play Instructions

    7. Operation 7-3 play instructions play instructions and techniques are indicated on stickers a and b..

  • Page 55: Shooting

    8. Inspection, cleaning and trouble- shooting to be conducted bv a technician 8-1 inspection and cleaning l before cleaning, or troubleshooting, unplug the power cord from the service outlet to prevent an electrical shock. To prevent an electrical shock, do not perform any work with wet hands. Every...

  • Page 56: 8-2 Troubleshooting

    Inspection, cleaning and trouble-shooting be conducted by a technician only 8-2 troubleshooting l before checking the product for proper installation and connection, off the power switch on the cabinet and unplug the power cord from the service outlet to prevent an electrical shock. Should any probl...

  • Page 57

    8. Inspection, cleaning and trouble-shooting be conducted by a technician only. Symptom possible cause action machine does not power supply is not connected check to make sure the power supply is operate when power properly in the cabinet. Connected properly in the cabinet. Switch is turned on. Powe...

  • Page 58

    9. Removal, storage and transportation removal to be conducted by a technician only l before conducting the following work, unplug the power cord from the service outlet to prevent an electrical shock. L remove static electricity from your body before touching the pc board. Static electricity can ca...

  • Page 59

    9. Removal, storage and transportation disconnect all cables and harnesses from the pc board. Ii , , i remove the four mounting screws from the pc board, and dismount the pc board fmm the mounting plate. Reinstall the mounting plate, and close the pc board compartment..

  • Page 60: 9-2 Storage

    9. Removal, storage and transportation 9-2 storage after removing the product, package the product with the packing materials that came with the product, and store in a clean place. Do not place any heavy item on the product package. L do the product in any of the following places to prevent damage....

  • Page 61: 10. Discarding The Product

    10. Discarding the product l never product i ery or electronic parts contained in the product can explode and cause injuries. When discarding the product, be sure to collect, transport and dispose of the product according to the law. L when entrusting another party to collect, transport and dispose ...

  • Page 62: 11. Parts List

    11. Parts list for parts, contact your distributor nai p/n q t y 1 1 description decal, marquee decal, side panel, left decal, side panel, right decal, control panel overlay decal, logo decal, player 1 decal, player 2 . Decal, punch decal, kick card, game instructions card, move list label, epilepti...

  • Page 63

    Oo-szoo l-sop 00-9000 00-zzoo ‘ws-a.

  • Page 65: Warranty

    Warranty seller warrants that its printed circuit boards and parts thereon are free from defects in materials and under use and service a of ninety days from date shipment. Seller warrants that its video displays (in games supplied with video displays) are free from defects in material and workmansh...

  • Page 66

    Namco america inc. 890 st. #c san jose, ca 95 112 (408) 383-3900 fax: (408) 436-9554 technical assistance (usa): phone: (408) 383-3973 fax: reorder number rev a. Published in august, 200 the specifications of this machine and the instructions in this operation manual are subject to change without no...