Napa 6-787 User Manual

Manual is about: AIR DRILL 3/8" REVERSIBLE ANGLE HEAD

Page of 12

Download

Print this page

Bookmark us

6-787

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement

and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to filter out microscopic particles.

ALWAYS READ

INSTRUCTIONS

BEFORE USING

POWER TOOLS

ALWAYS WEAR

SAFETY GOGGLES

WEAR HEARING

PROTECTION

AVOID

PROLONGED

EXPOSURE TO

VIBRATION

3/8" REVERSIBLE ANGLE HEAD

AIR DRILL

Rev. 10/07/05

6-787_Manual_100705.indd 1

10/7/05 8:16:24 AM

1 2 3 4 5 6 7 Next › »

Summary of 6-787

Page 1
6-787 some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement...
Page 2
This instruction manual contains important safety information. Read this instruction manual carefully and understand all information before operating this tool. • always operate, inspect and maintain this tool in accordance with american national standards institute safety code of portable air tools...
Page 3: Air Supply
Rev. 08/30/05 nipple tools of this class operate on a wide range of air pressures. It is recommended that air pressure of these tools measures 90 psi at the tool while running free. Higher pressure (over 90 psig; 6.2 bar) raises performance beyond the rated capacity of the tool, which will shorten t...
Page 4: Operation
Rev. 10/07/05 locate center of new hole by using a center punch. Place drill bit tip in punch mark. Hold drill square with work and start motor. Apply steady, even pressure. Do not force. Too much pressure can cause bit to break or overheat. Too little pressure will keep the bit from cutting and cau...
Page 5: Parts Breakdown
Rev. 10/07/05 parts breakdown please review all warning instructions prior to operation. Save this manual for future reference. 5 parts list 6-787 ref. # item # description qty. 1 rs78701 motor housing 1 2 rs233a02 spring pin 1 3 rs233a03 air inlet 1 4 rs78704 throttle lever 1 5 rs78705 valve stem 1...
Page 6: Troubleshooting
Rev. 10/07/05 impact wrenches tool runs slowly or not at all and/or air flows only slightly from exhaust — this is probably caused by: air flow blocked by dirt build-up; motor parts jammed with dirt; power regulator has vibrated to closed position. You should: check air inlet strainer for blockage. ...
Page 7: Taladro De Aire
Reversible del 3/8" capeza del angulo taladro de aire ® rev. 10/07/05 advertencia se sabe que el polvo generado por el lijado, la aserradura, el esmerilado, la perforación mecánica y por otras actividades de construcción contiene químicos que producen cáncer, malformaciones congénitas u otros daños ...
Page 8
Rev. 10/07/05 ▲ advertencia! Al no seguir todas instrucciones de la lista abajo puede provocar lesiones graves este manual de instrucciones contiene importantes informaciones de seguridad. Lea cuidadosamente y asegÚrese de comprender todas estas informaciones, antes de proceder con el funcionamiento...
Page 9: Abastecimiento Del Aire
Rev. 10/07/05 las herramientas que se encuentran en esta clase funcionan con una variedad grande de presiones del aire. Recomendamos que la presión del aire para estas herramientas sea de 90 psi en la herramienta; funcionando a una presión más alta (más de 90 psi; 6.2 bar) levanta los resultados más...
Page 10: Funcionamiento
Rev. 10/07/05 ® coloque el centro del nuevo agujero utilizando un punzón. Coloque la extremidad de la broca del taladro en la marca del punzón. Mantenga el taladro nivelado con el lugar del trabajo y arranque el motor. Aplique una presión estable e igual. No aplique fuerza. La broca puede romperse o...
Page 11: Problemas Y Soluciones
Rev. 10/07/05 problemas y soluciones revise todas las informaciones de advertencia, antes de proceder con el funcionamiento. Conserve este manual para tener una referencia eventual. 10 llaves de impacto la herramienta funciona lentamente o no funciona en absoluto y / o el aire emana solamente un poc...
Page 12: Problemas Y Soluciones
Rev. 10/07/05 problemas y soluciones política de garantía: las herramientas napa professional air tools están garantizadas contra cualquier falta de material o de mano de obra durante un periodo de un (1) año a partir de la fecha de la compra original. Reemplazaremos o repararemos a nuestra elección...