Napa IMPACT WRENCH Instruction manual

Manual is about: 1" DRIVE HEAVY DUTY IMPACT WRENCH w/6" Ext. Anvil

Summary of IMPACT WRENCH

  • Page 1

    6-794 1 rev. 06/06/03 6-794 some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica ...

  • Page 2

    6-794 2 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Failure to observe these warnings could result in injury. This instruction manual contains important safety information. Read this instruction manual carefully and understand all i...

  • Page 3: Air Supply

    6-794 3 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Nipple leader hose whip hose nipple filter air supply regulator quick coupler oiler drain daily do not install quick coupling here air supply lubricate the air motor daily with nap...

  • Page 5: Pecifications

    6-794 5 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. This impact wrench is rated at 1-1/4" uss bolt size. Rating must be down graded for spring u bolts, tie bolts, long cap screws, double depth nuts, badly rusted conditions and sprin...

  • Page 6: Troubleshooting

    6-794 6 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Troubleshooting impact wrenches tool runs slowly or not at all and/or air flows only slightly from exhaust. This is probably caused by: air flow blocked by dirt build-up; motor par...

  • Page 7: Troubleshooting

    6-794 7 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Troubleshooting air drills tool will not run, runs slowly, air flows slightly from exhaust, spindle turns freely. This is probably caused by: air flow blocked by dirt build-up; mot...

  • Page 8

    Please review all warning instructions prior to operation. Save this manual for future reference. Al no seguir todas instrucciones de la lista abajo puede provocar lesiones graves este manual de instrucciones contiene importantes informaciones de seguridad. Lea cuidadosamente y asegÚrese de comprend...

  • Page 9: Abastecimiento Del Aire

    6-794 9 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Las herramientas que se encuentran en esta clase funcionan con una variedad grande de presiones del aire. Recomendamos que la presión del aire para estas herramientas sea de 90 psi...

  • Page 10: Funcionamiento

    6-794 10 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Coloque el centro del nuevo agujero utilizando un punzón. Coloque la extremidad de la broca del taladro en la marca del punzón. Mantenga el taladro nivelado con el lugar del traba...

  • Page 11: Problemas Y Soluciones

    6-794 11 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Problemas y soluciones llaves de impacto la herramienta funciona lentamente o no funciona en absoluto y / o el aire emana solamente un poco del sistema de escape — la causa probab...

  • Page 12: Problemas Y Soluciones

    6-794 12 rev. 06/06/03 please review all warning instructions prior to operation. Save this manual for future reference. Problemas y soluciones debe: verifique la entrada del aire para detectar un bloqueo posible. Eche una cantidad generosa de aceite para herramientas con aire dentro de la entrada d...