NAPCO GEM-EZM4/8 Addendum - page 4
4
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its
products to be free from manufacturing defects in materials and
workmanship for thirty-six months following the date of manufacture.
NAPCO will, within said period, at its option, repair or replace any
product failing to operate correctly without charge to the original
purchaser or user.
This warranty shall not apply to any equipment, or any part
thereof, which has been repaired by others, improperly installed,
improperly used, abused, altered, damaged, subjected to acts of God,
or on which any serial numbers have been altered, defaced or
removed. Seller will not be responsible for any dismantling or
reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED,
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN
LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF NAPCO.
Any action for breach of warranty, including but not limited to any
implied warranty of merchantability, must be brought within the six
months following the end of the warranty period. IN NO CASE SHALL
NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR
DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR
FAULT.
In case of defect, contact the security professional who installed
and maintains your security system. In order to exercise the warranty,
the product must be returned by the security professional, shipping
costs prepaid and insured to NAPCO. After repair or replacement,
NAPCO assumes the cost of returning products under warranty.
NAPCO shall have no obligation under this warranty, or otherwise, if
the product has been repaired by others, improperly installed,
improperly used, abused, altered, damaged, subjected to accident,
nuisance, flood, fire or acts of God, or on which any serial numbers
have been altered, defaced or removed. NAPCO will not be
responsible for any dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty
and any prior agreements or representations, whether oral or written,
are either merged herein or are expressly cancelled. NAPCO neither
assumes, nor authorizes any other person purporting to act on its
behalf to modify, to change, or to assume for it, any other warranty or
liability concerning its products.
In no event shall NAPCO be liable for an amount in excess of
NAPCO's original selling price of the product, for any loss or damage,
whether direct, indirect, incidental, consequential, or otherwise arising
out of any failure of the product. Seller's warranty, as hereinabove set
forth, shall not be enlarged, diminished or affected by and no
obligation or liability shall arise or grow out of Seller's rendering of
technical advice or service in connection with Buyer's order of the
goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE
COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to,
any or all of the following; criminal tampering, electrical or
communications disruption, it is possible for the system to fail to
perform as expected. NAPCO does not represent that the product/
system may not be compromised or circumvented; or that the product
or system will prevent any personal injury or property loss by burglary,
robbery, fire or otherwise; nor that the product or system will in all
cases provide adequate warning or protection. A properly installed
and maintained alarm may only reduce risk of burglary, robbery, fire
or otherwise but it is not insurance or a guarantee that these events
will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE,
OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO
GIVE WARNING. Therefore, the installer should in turn advise the
consumer to take any and all precautions for his or her safety
including, but not limited to, fleeing the premises and calling police or
fire department, in order to mitigate the possibilities of harm and/or
damage.
NAPCO is not an insurer of either the property or safety of the
user's family or employees, and limits its liability for any loss or
damage including incidental or consequential damages to NAPCO's
original selling price of the product regardless of the cause of such
loss or damage.
Some states do not allow limitations on how long an implied
warranty lasts or do not allow the exclusion or limitation of incidental
or consequential damages, or differentiate in their treatment of
limitations of liability for ordinary or gross negligence, so the above
limitations or exclusions may not apply to you. This Warranty gives
you specific legal rights and you may also have other rights which
vary from state to state.
NAPCO LIMITED WARRANTY
LOOP RESPONSE
Loop response times for Zones 1 through 8 are programmed in the control panel. Normal loop response for all expansion
zones is 750mS. The module already comes without the jumper installed (defaulted to 750ms). To reduce the response time of
zones 1 through 4 of the EZM Module to 50mS, add the Loop Response Jumper. To enable normal loop response (750 ms),
remove the jumper. Refer to the Wiring Diagram.
STATUS LED
The Status LED displays the condition of the zone module. The following is a list of conditions for the LED:
1. OFF = Control Panel has no power applied.
2. ON Steady = Control Panel has power applied but the panel is not polling because:
a. the panel is in "CONFIG",
b. the panel is not programmed correctly to poll the address of the EZM,
c. the GRN wire is not connected correctly.
3. PULSES off the EZM groups that are being polled.
a. If the first EZM group (the base number) is polled the LED is normally on and pulses off once slowly.
b. If the first and second EZM group are polled then the LED is normally on and pulses off once then twice sequentially.
c. If the first, second, third and fourth groups are polled the LED is normally off and will pulse 1, 2, 3, 4 sequentially.
4. Rapid Flashing.
a. GEM-EZM4/8 is connected to wrong panel type.
NOTE: Only GEM-P1664 may be connected.