NAPCO NETLINK Datasheet - page 2
NAPCO Product Availability Hotline – Call our Stock-Out Hotline at 1-800-645-9330 Press 1, pause, then 2.
Or email us at hotline@napcosecurity.com
333 Bayview Avenue, Amityville, New York 11701 USA
•
1-800-645-9445
•
www.napcosecurity.com
Preliminary specifications, subject to change. Gemini, NetLink and Quickloader are trademarks of NAPCO.
Windows, Dell, Intel and Pentium are trademarks of their respective companies. © NAPCO, 9/04 A482
PRELIMINARY SPECIFICATIONS:
NETLINK PANEL MODULE (NL-MOD):
The PC-configurable NAPCO NetLink™ NL-MOD enables
reporting of alarms over a TCP/IP based (Intranet or Internet)
network. Alarm reporting, previously via telephone lines/
telco only, can now be
communicated over
both a TCP/IP network
and/or Telco, or via the
TCP/IP network as a
backup. The NL-MOD
module is connected to
the on-board serial port
of the GEM-X255, GEM-
P3200 and GEM-P9600
NAPCO GEMINI Control Panel, or is connected via the bell
and PGM wires from the GEM-P1632, GEM-P816, NAPCO
Express and other control panels.
NetLink Central Station Receiver Application (NL-CSRCV)
The NetLink Software, NL-CSRCV, is a Windows-based
application that is designed to act as a remote monitoring
receiver. In place of receiving alarm data through a telephone
line, the NL-CSRCV application receives encrypted alarm
data sent from the NL-MOD through a TCP/IP network. The
NL-CSRCV software can supervise each NL-MOD, receive
alarms, provide a means of maintaining accounts and provide
a means of displaying alarms and event history (opening/
closing, etc.). The NL-CSRCV could be used to display
alarm events locally or can be used to route events to an
automation system. For more information, see the NL-CSRCV
User Guide OI294.
NL-MOD SPECIFICATIONS:
Dimensions: 1 1/2” x 7” x 4 3/4” (HxWxD)
Input Voltage: 13.0-10.0VDC.
Input Current: Maximum current (@8 VDC) = 100mA,nominal
current (@12VDC) = 80mA (supplied by control panel
connections). Available panel combined auxiliary current is
reduced by 100mA.
Outputs: PGM-style open collector (negative trigger) with a
maximum sink current of 50mA.
SYSTEM REQUIREMENTS:
System Hardware Requirements:
•
Compatible Gemini Control Panels GEM-X255, GEM-P3200
and GEM-P9600; GEM-P1632, GEM-P816 (check WI for
exact firmware version)
•
Standard 6 conductor modular RJ12 Cable, 1 foot in length
(provided). Required for full zone reporting/downloading.
•
Access to the local area network.
•
A standard CAT5 network cable for connection to the LAN
PC Requirements for Software (NL-CSRCV):
•
Windows® XP Professional installed on a dedicated PC
•
Intel® Pentium® 4 (2GHz processor or faster) with at least
512 MB RAM.
•
Hard drive space 20GB or higher.
•
NAPCO Tested and certified using a Dell™ Dimension™
Series 2400 & 4400 PC. (For other models, contact Napco
Technical Support.)
•
Network Card requirements: 100 BaseT Ethernet.
Note: Not supported - Hyper-Threading technology, Dual Processors and Windows®
XP Themes.
ORDERING INFORMATION:
NL-MOD NetLink Panel Module
NL-CSRCV Central Station Receiver Application Software for
use in standard PC.
NL-CSRCV/PC Above, preinstalled and configured in turnkey
computer system. (Call for PC specs or special requirements.)
NL-MODCONFIG Download software utility for initially
programming/configuring Panel Module.
PCD-WINDOWS Napco Panel Up/Downloading Software
(version 4.4 or greater)
Publicly traded on
NASDAQ
NSSC