NAPCO NP-DTM7D24H-D Features - page 3
Depress ENTER. will appear in display.
E. BLOCK EVENT PROGRAMMING
Flashing cursor will appear at the location of the first day of
the week desired. Depress UP and DWN to select day.
Depress ENTER to confirm selection, then cursor will appear
at the location of the last day of the week desired.
Depress UP and DWN to select day. Depress ENTER to
confirm selection.
1) Monday through Thursday depress MO followed by TH.
2) Wednesday through Sunday depress WE followed SU.
F. DAYLIGHT SAVING PROGRAMMING
The cursor will appear under DS (auto clock adjust daylight
saving mode) in display. To change mode, depress UP or
DWN once. ST (clock does not adjust standard time mode)
will appear in display. Depress ENTER to accept correct se-
lection.
Note: Select DS for areas that observe Daylight Saving or ST
for areas that do not observe Daylight Saving.
G. SETTING HOLIDAY EVENTS
(These events will occur on programmed Holiday Dates - see
Setting Holiday Dates below). Select channel A or B by mov-
ing slide switch SW1 to appropriate position.
Note: Channel cannot be changed in the middle of program-
ming events. To change channels, you must exit program-
ming, then change channel switch position, then enter pro-
gram mode again.
Find the first unprogrammed event (refer to C. Adding
Events). Depress ENTER until the flashing cursor appears
under OFF (relay function) position in display. Now select
type of operation required, by scrolling using the UP and
DWN push buttons until either:
ON - Relay ON (latching mode).
OFF - Relay OFF (latching mode).
PL - Relay Pulse (momentary).
...appears in display and depressing ENTER will make selec-
tion.
When selecting the pulse mode, PL01 will appear in the dis-
play. It is now necessary to assign the length of time (duration
of relay activation). The pulse can range in length from 1-
second minimum to 15 seconds maximum and is selected by
using the UP or DWN push buttons, then depressing ENTER
to accept.
Note: If pulse duration is not selected, relay output defaults to
1 second.
Next select HL (holiday) and time (military) by scrolling using
UP and DWN push buttons and depressing ENTER to ac-
cept. You may continue to program events by repeating the
previous steps or exit programming by depressing SET.
H. SETTING HOLIDAY DATES:
Select channel A or B by moving slide switch SW1 to ap-
propriate position.
Note: Channel cannot be changed in the middle of program-
ming events. To change channels you must exit program-
ming, then change channel switch position, then enter pro-
gram mode again. It is now necessary to assign these holi-
day events specific calendar dates, which they are to occur.
Depress SET until appears in display.
Depress ENTER. will appear in display.
Enter the holiday date, day of week and year by depressing
UP and DWN to make the selection then depress ENTER to
accept.
Note: Holiday events will override all regularly programmed
events that occur on a particular holiday date.
I. DELETE/DISABLE EVENTS OR EDIT EVENTS:
Select channel A or B by moving slide switch SW1 to ap-
propriate position.
Note: Channel cannot be changed in the middle of program-
ming events. To change channels you must exit program-
ming, then change channel switch position, then enter pro-
gram mode again. Previously programmed regularly sched-
uled and/or holiday events may be deleted/disabled without
having to erase all events.
Depress SET until appears in display.
Depress ENTER will appear in display.
Now scroll using UP and DWN push buttons to the event you
wish to delete, depress ENTER to move flashing cursor under
relay option, then depress UP and DWN push buttons until
DIS is displayed, depress ENTER to confirm.
J. DELETE ALL EVENTS:
This will delete all previously programmed events.
SET until appears in display.
Depress ENTER. will appear in display.
Depress ENTER. will appear in display.
Depressing UP push button will now clear all events previ-
ously programmed.
If you wish to escape from this selection, depress any of the
other push buttons: SET, ENTER and DWN.
K. TANDEM RELAY MODE:
To operate in the Tandem Relay Mode, close switch SW2
and cut R3. This mode setting will allow events programmed
for Channel A and Channel B to operate both relays simulta-
neously (1 DPDT relay output). This setting doubles the
amount of programmable events.
Note: When using the Tandem Relay mode, sequential ON/
Off or OFF/ON events must be programmed in the same
channel. (If there is a Channel Program conflict, such as
Channel A is set to ON and Channel B is set to OFF, the ON
command will override the OFF command and both relays will
remain ON).
A01 ^ ON
HL 00:00
ENTER TO
SET EVENT
A = SA/SU
TIME = DS
A01 ^ ON
TU 00:00
ENTER TO
SET EVENT
ENTER TO
CLR MEM
CLEAR
MEMORY?
PRESS UP
& ACCEPT