Off hig h manual,instructions & parts list patio heater for your safety if you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues ,immediately call gas supplier. For your safety do not store or use gasoline or other flammable vapors or liquids in the vici...
2 tools and parts needed for assembly tools and parts needed for assembly tools needed: 7/16 wrench 3/8 open end wrench adjustable opening wrench, 8 long philips head screwdriver leak detection solution ( instructions how to make solution are included in step 8 ) ＂ ＂ ＂ warning note: 20 pound, 5 gall...
3 parts parts 15 17 1 regulator 1 cylinder (not supplied) 1 2 3 4 5 6 7 8 9 10 11 4 reflector cap 1 head assembly 1 gas hose 1 post 1 cylinder cover 1 cylinder base 15 m6 nuts 18 6mm washers 5 m4 8 bolts x 3 post mounts 10 12 1 center reflector cap 12 m6 10 bolts x 13 15 16 3 m6 x70 double pointed b...
4 precautions precautions do not use the heater in an explosive atmosphere. Keep the heater away from areas where gasoline or other flammable liquids or vapors are stored. Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. Never replace or substitute the regulator with...
Assembly for light system assembly for light system warning: to be installed only by an authorised person instruction for battery installing upon first time use of the product,please remove the ignition button and install an aaa battery as indicated. Ignition button replace battery control knob igni...
6 assembly assembly note: assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 1 ---- step 1 step 2 ---- step 2 m5 x 8 bolts (6 pcs) and 5mm washers (6 pcs) attach the post to the post mounts using attach post to base assembly 7 attac...
7 assembly assembly note: assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 3 ---- attach head assembly to post load head assembly by inserting gas hose into post. Insert head assembly into post. Tighten securely using m4 x 8 bolts...
Step 5 ---- attach center reflector to reflector attach center reflector to the top of reflector (4 pcs) by m6 x 10 mm screws (12 pcs) , step 5 2 1 15 6mm washers (12 pcs) and nuts (12 pcs). Step 6 ---- attach center reflector and reflector load center reflector and reflector to the top of head asse...
9 assembly assembly step 7 step 8 note: assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 7 ---- connect gas line to cylinder step 8 ---- check for leak attach gas hose to regulator with 3/8 inch open end wrench and adjustable wren...
10 assembly assembly step 9---- lower cylinder cover onto cylinder base lower the cylinder cover onto the cylinder base . Step 9 6 8 warning : to be installed only by a competent person step 10---- step 10 6 disconnect cylinder when storing or transporting 7 1).Turn off the heater; 2).Upper the cyli...
Operation operation warning: do not attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. Before turning gas supply on your heater was designed and approved for outdoor use only. Do not use it i...
Operation operation operation operation caution : avoid inhaling fumes emitted from the heater's first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should not produce thick black smoke. "...
13 locating header for use locating header for use figure 1 this heater is primarily used for the heating of outdoor patios, decks, spas, pool and open working areas. Always make sure that adequate fresh air ventilation is provided. Follow the spacing tolerances shown in figure 1. The minimum cleara...
14 maintenance/storage maintenance/storage maintenance : to enjoy years of outstanding performance from your heater make sure you perform the following maintenance activities on a regular basis: keep exterior surfaces clean. Use warm soapy water for cleaning. Never use flammable of corrosive cleanin...
15 troubleshooting troubleshooting problem probable cause solution pilot will not light gas valve may be off turn the gas valve on orifice blocked clean or replace orifice air in supply system purge air from lines pilot will not stay on debris around pilot clean dirty area loose connection tighten c...
