If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appl...
This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent or home. Danger carbon monoxide hazard warning: improper installation, adjustment, alteration, service or maintenance can cau...
The installation must conform with local codes or, in the absence of local codes, with the national fuel gas code, ansi z223.1/nfpa 54, nfpa58 natural gas and propane installation code, csa b149.1, or propane storage and handling code, b149.2 the heater, when installed, must be electrically grounded...
Within a partial enclosure which includes an overhead cover and three side walls, as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open. This appliance requires 9kg(20lb) lp-gas supply cylinder. The lp-gas supply cylinder to be used must be: constructed and m...
This heater is designed to operate with a standard 20 ib propane cylinder with approved cylinder connection. Note: please read the following safety rules: adjustable opening wrench philips screwdriver estimated time for assembly: 30 minutes. Before beginning assembly of product, make sure all parts ...
6 parts list / exploded view 1 2 3 4 5 15 6 17 7 8 9 10 11 12 13 14 16 18 19 5 4mm washers 6 5mm washers 3 m4x6 bolts 3 m6x14 bolts 15 m6 nuts 18 6mm washers 12 m6x10 screws 3 m6x70 double pointed bolts 5 m4x8 bolts 6 m5x8 bolts 1 cylinder chain 1 center reflector cap 5 reflector caps 1 burner assem...
Warning: read all assembly instructions thoroughly and carefully to insure proper, safe assembly . Step 1 step 2 assembly 5 16 17 18 8 6 hardware used hardware used 5mm washer x 6 m5 x 8 bolt x 6 m6 x 14 bolt x 3 step 1 step 2 insert low pole (5) into the pole supporting board (8) , fix it with 6 pc...
Step 3 assembly 13 15 14 hardware used m4x6 bolts x 3 hardware used 4mm washer x 5 m4 x 8 bolt x 5 step 3 step 4 4 3 4 5 14 step 4 connect the upper pole (4) on the low pole (5) , fix it with 3pcs m4×6 bolt (14) . Insert the burner assembly (3) in the upper pole (4) , fix it with 5pcs 4mm washer (15...
Assembly step 5 9 9 10 9 10 12 11 hardware used m6 nut x 12 m6x10 screw x 12 6mm washer x 12 m6 nut x 3 m6x70 double pointed bolts x 3 6mm washer x 6 hardware used step 5 step 6 、 step 6 attach the center reflector cap (1) on the top of the four reflector cap (2) by twelve sets of m6x10 screw (11) ,...
10 assembly step 7 open the door ,put cylinder into the big hole on bottom panel and lock the cylinder chain . Step 7 tighten.
11 check for leaks your patio heater has been checked at all factory connections for leakage. To check the connection at the gas hose/regulator /cylinder. Note: 1) the cylinder supply system must be arranged for vapor withdrawal. 2) the cylinder used must include a collar to protect the cylinder val...
12 instruction for installing battery remove igniter button by turning counter-clockwise.Install “aaa” battery with positive terminal up as indicated in diagram. Replace igniter button. Igniter battery installation ignition button control knob aaa battery ignition button replace battery.
13 operation before turning gas supply on warning: do not attempt to operate heater until you have read and understand all precautions . Failure to do so can result in serious personal injury, death, or property damage. Before lighting heater should be thoroughly inspected before each use, and by a ...
14 operation yellow tip primarily blue flame flame characteristic the flame pattern at the emitter screen should be visually checked whenever heater is operated. Normally the burner flame is blue, but little yellow flame is acceptable. If the flames extend beyond the surface of the emitter grid, or ...
15 operation note: the burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the "low" position. Then, turn the knob to the level of heater desired. When heater is on: emitter screen will become bright red due to intense heat. The color ...
16 locating header for use caution: when certain materials or items are left, above, beside or under this heater while in use, they will be subject to radiant heat and could be seriously damaged. This heater is primarily used for the heating of outdoor patios, decks, spas, pools and open working are...
17 maintenance/storage yellow tip primarily blue flame do not touch or move heater for at least 45 minutes after use. Allow all burner elements to cool before touching. For your safety ; warning: check for cracks or worn sections note: in a salt-air environment (such as near an ocean). Corrosion occ...
18 maintenance/storage note: wait until heater is cool before covering. Turn the control knob to "off" position. Turn lp cylinder to "off" position. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, co...
19 problem probable cause solution pilot will not light gas valve may be off turn the gas valve on tank fuel empty refill lp gas tank air in supply system purge air from lines loose connection loose connection check all fittings pilot will not stay on debris around pilot clean dirty area tighten con...
20 one-year limited warranty the appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for one (1) year from the date of purchase. A re...
