Narda safety test solutions s.R.L. Socio unico sales & support: via leonardo da vinci, 21/23 20090 segrate (mi) - italy tel.: +39 02 2699871 fax: +39 02 26998700 manufacturing plant: via benessea, 29/b 17035 cisano sul neva (sv) tel.: +39 0182 58641 fax: +39 0182 586400 http://www.Narda-sts.It seria...
Ii note and symbols note: if the instrument is used in any other way than as described in this users manual, it may become unsafe before using this product, the related documentation must be read with great care and fully understood to familiarize with all the safety prescriptions. To ensure the cor...
Contents iii contents general safety considerations and instructions......... Ec conformity certificate………………………………... 1 general information 1.1 documentation.....................................…...............… 1.2 introduction ……………….....................................…. 1.3 instrument items.......
Iv contents figures figure 1-1 1-2 front panel.......................................….....…... Rear panel........................................…........... Page 1-6 1-6 tables table 1-1 technical specifications...................…........... Page 1-2.
Safety consideration v safety recommendations and instructions this product has been designed, produced and tested in italy, and it left the factory in conditions fully complying with the current safety standards. To maintain it in safe conditions and ensure correct use, these general instructions m...
Vi ec conformity e c c o n f o r m i t y c e r t i f i c a t e (in accordance with the directives: emc 89/336/eec and low voltage 73/23/eec) this is to certify that the product: pmm 6000n wideband rf power amplifier produced by: narda s.R.L. Safety test solution via benessea 29/b 17035 cisano sul ne...
General information 1-1 1 - general information 1.1 documentation enclosed with this manual are: • a service questionnaire to send back to narda in case of equipment service is needed • an accessories check list to verify all accessories enclosed in the packaging. 1.2 introduction pmm 6000n is a wid...
1-2 general information 1.5 main specifications table 1-1 lists the pmm 6000n performance specifications. The following conditions apply to the specification: • the pmm 6000n needs at least 5 minutes warm-up before operate; • the ambient temperature shall be 10° to 40° c. Table 1-1 technical specifi...
General information 1-3 1.6 typical performances typical gain at nominal power [db] 30 32 34 36 38 40 42 44 46 48 50 0.001 0.01 0.1 1 10 100 1000 [mhz] [db] typical gain at nominal power/2 [db] 30 32 34 36 38 40 42 44 46 48 50 0.001 0.01 0.1 1 10 100 1000 [mhz] [db].
1-4 general information power output at 1dbc [w] 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 0.001 0.01 0.1 1 10 100 1000 [mhz] [w] compression at nominal power [dbc] 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 0.001 0.01 0.1 1 10 100 1000 [mhz] [db].
General information 1-5 -45 -40 -35 -30 -25 -20 -15 -10 -5 0 0.001 0.01 0.1 1 10 100 1000 [mhz] [dbc] 2nd harmonic at pn [dbc] 3rd harmonic at pn [dbc].
1-6 general information 1.7 front panel fig 1-1: front panel legend: 1 - input bnc connector 2 - output n connector 3 - power meter 4 - power on light 5 - alarm light 1.8 rear panel fig 1-2: rear panel legend: 1 - mains power switch 2 - fuse receptacle 3 - mains power connector 4 - equipment serial ...
Installation 2-1 2 - installation 2.1 introduction this section provides the information needed to install your pmm 6000n. Included is information pertinent to initial inspection, power requirements, line voltage and fuse selection, power cables, interconnection, environment, instrument mounting, cl...
2-2 installation 2.7 fuse selection line voltage fuse rating type 85 ÷ 264 v 1,6 at slow action before connecting this instrument, ensure that an uninterruptible safety earth ground is provided from the main power source to the product protective earth connection. If this instrument is to be connect...
Operating instruction 3-1 3 - operating instruction 3.1 cooling it is necessary to ensure that the pmm 6000n forced-air cooling system be allowed to operate at maximum efficiency. Cooling depends upon the free flow of cooling air through the bottom and the rear of the unit. Take care to keep these a...
3-2 operating instruction this page intentionally left blank.
Narda safety test solutions s.R.L. Socio unico sales & support: via leonardo da vinci, 21/23 20090 segrate (mi) - italy tel.: +39 02 2699871 fax: +39 02 26998700 manufacturing plant: via benessea, 29/b 17035 cisano sul neva (sv) tel.: +39 0182 58641 fax: +39 0182 586400 http://www.Narda-sts.It mod. ...
Suggerimenti / commenti / note: suggestions / comments / note:.
