Narex ASV 7 E Instructions For Use Manual - English
English
8
Technical Specification
Cordless drill screwdriver:
Model
ASV 7 E
Voltage.
.
7,.V
Accumulator.cell.type.
.
Li-Ion
Accumulator.capacity.
.
1,.Ah
Idle.speed.
.
0.–.400.min
-1
Max..torque.
.
1.Nm
Screwing.wood.screws.
.
max.ø.4,5.mm
Clamping.on.the.spindle.
.
¼“.hexagon
Weight.of.the.device.without.extensions.
0,8.kg
Charger:
Input.voltage.
.
0.–.40.V
Frequency.
.
50.Hz
Power.input.
.
5.W
Output.voltage.
.
7,.V
Charging.current.
.
500.mA
Charge.time.
.
ca.,5.hours
Weight..
.
0,8.kg
Class.of.protection.
.
II./
Description:
1...........Clampsleeve
2...........Adjustingringfortorquesetting
3...........LEDlighting
4...........Reversingswitch
5...........Switching-inpushbuttonwithspeedcontrol
6...........Accumulatorchargepilotlamp
7...........Jack
8...........Chargercable
9...........Charger
Information about noise level and vibrations
WeighedsoundpressurelevelLPAis66.3dB(A).
WeighedsoundpowerlevelLWAis77.3dB(A).
Weighedlevelofarmaffectingvibrationsislessthan2.5m/s
2
.
Scope of use:
Thecordlessdrillscrewdriversarespecifiedfordrillingintometals,
woodsandplasticsandforscrewing.
Instructions for charging
1.Connect the charger cable (8) to the jack (7) on the bottom
screwdriverhandleside.
2.Checkthatthemainsvoltageconformstothevoltageshown
on the charger rating plate. Connect the charger (9) to the
socket.
3.Afterthechargerisconnectedtothesocket,thechargepilot
lamp (6) will go on. The pilot lamp indicates the running
processofcharging.
4.In most cases charging for ca 2.5 hours is quite enough. As
soonastheaccumulatorischarged,thechargingpilotlamp
(6)willgooff.Putthecharger(9)outofthesocketandthen
disconnectitscable(8)fromthedevice.
Attention!
DONOTUSEthedeviceduringcharging.
Note:
· The accumulator is supplied unloaded by the manufacturer.
Therefore 5 to 10 cycles of charging and discharging are
neededtoreachitsfullcapacity.
· Thechargerworksbestattheroomtemperature.
· During charging both the charger and the screwdriver can
warmup.Thisisanormalphenomenonduringtheprocessof
chargingandcannotbeunderstoodaproblem.
Important instructions for charging:
· Donotchargethedeviceinahumidorwetenvironment.
· The max. service life of the accumulator and the best
performancecanbereachedbychargingtheaccumulatorat
theambienttemperaturerangeof18°Cto24°C.
· Do not charge the accumulator battery at the temperatures
below 4.5°C or above 40.5°C to avoid serious accumulator
damage.
· During charging both the accumulator and the charger can
warmup.Thisisanormalphenomenonduringtheprocessof
chargingandcannotbeunderstoodaproblem.
· Toavoidpossibleoverheatingdonotcoverthechargerduring
charging,donotchargetheaccumulatorindirectsunlightor
closetoheatsources.
If the accumulator is not charged dully:
a/ Place the charger and the accumulator to the environment
withthetemperaturerangingfrom18°Cto24°C
b/Iftheproblemswithchargingpersist,handthedeviceandthe
chargerovertothenearestauthorizedservicecentre.
· Chargetheaccumulatorwhenitisnomoreabletoreachthe
originalperformance.Iftheaccumulatorisdischarged,donot
useitbeforerecharging.Followtheinstructionsforcharging.
· Prevent penetration of el. conductive impurities to charger
contacts.
· When the charger is not operated, disconnect it from the
powersupply.
· Before cleaning the charger, disconnect it from the power
supply.
· Donotexposethechargertofrost,donotdipitintowateror
anotherliquid.
WARNING!!
Preventpenetrationofliquidsintothechargerasitcouldresultin
electricshock.Donotletthemachineinahotenvironmentsothat
theaccumulatormaycoolafteruse.