E8 swing automatic gate. Revision 1.1.8 –1112 1 of 19 e8 arm gate motor and control panel installation guide contents important safety information, important observations…………. 2 specification, standard packing …………….………………………. 3 gate post positioning, gate preparation, installation pointers..……. 4 i...
E8 swing automatic gate. Revision 1.1.8 –1112 2 of 19 important safety information all safety instructions and installation methods should be read and completely understood by installer and the owner prior to the installation of the autogate system. This product is designed and manufactured for the ...
E8 swing automatic gate. Revision 1.1.8 –1112 3 of 19 specification supply voltage : single phase 220-240vac or solar backup battery : lead acid maintenance free 12v 7ah operating voltage : dc 16-18v for normal speed dc 6-10v for cushioning speed driving method : screw driven type max. Out...
E8 swing automatic gate. Revision 1.1.8 –1112 4 of 19 gate post bracket positioning in a standard installation the basic aim is to get the “j” and “k” dimensions to be as close as possible to equal but “j” can be greater allowing for a more positive push of the gate against gate stop. Hint: the dime...
E8 swing automatic gate. Revision 1.1.8 –1112 5 of 19 installing gate post brackets and the arms (push-to-close/ pull-to- open) retract the arms (you can use the backup battery to help retract the arms) and open the gates to the fully-opened position. assemble the gate post brackets (primary wal...
E8 swing automatic gate. Revision 1.1.8 –1112 6 of 19 the arms should be approximately 10-15mm from full extension when the gate completely closes against the floor rubber stopper. O this is to ensure that when in operation, the arms will give a solid push to the gate onto the floor stopper. if ...
E8 swing automatic gate. Revision 1.1.8 –1112 7 of 19 installing gate post brackets and the arms for push-to-open gates installation method for push-to-open gates is similar to pull-to-open except that when the arms are retracted, the gates are in the closed position. note that for push-to-open ...
E8 swing automatic gate. Revision 1.1.8 –1112 8 of 19 mounting of the control panel box select a flat and sturdy surface for the mounting of the control panel box. Care must be taken to ensure that the mounting screws and holes on the control panel are properly sealed to prevent water seepage into t...
E8 swing automatic gate. Revision 1.1.8 –1112 9 of 19 control panel – model d1 the e8 d1 control panel is specially designed to match 12vdc arm gate motor(s). The electronic panel requires no maintenance as long as the gate operates in proper order and is kept dry and insect free. Mount the control ...
E8 swing automatic gate. Revision 1.1.8 –1112 10 of 19 setting the system : double gate operation (both pull-to-open and push-to-open gate) 1. Unplug ac power and battery and make sure the gate(s) are completely closed. 2. After 30 seconds reconnect power to the system until short clicking from boar...
E8 swing automatic gate. Revision 1.1.8 –1112 11 of 19 single gate operation: 1. Set dip switch [5] to on position and connect arm motor wires to [mt a] terminals. 2. Place / connect both receiver output wires together (yellow and brown) into the far right terminal [1 side]. 3. Place receiver common...
E8 swing automatic gate. Revision 1.1.8 –1112 12 of 19 remote control: the 12vdc remote transmitter contains two signal represented by button 1 and button 2 on your remotes. Confirm with owner which function they want for each of the button. Double gate setup button #1 can be set as single gate oper...
E8 swing automatic gate. Revision 1.1.8 –1112 13 of 19 solid gate-stops must be fitted in the center of driveway to give a solid pressure point between the stop and the end of each gate. Place a gate stop at the fully open position if desired. Arm condensation drain hole : always mount arms with con...
E8 swing automatic gate. Revision 1.1.8 –1112 14 of 19 external light connection d1 board has a 12vdc output on the lamp relay terminal. Left terminal is negative and right is positive. This output is to energize an external 12vdc relay which in turn can be used to turn on /off a higher rating elect...
E8 swing automatic gate. Revision 1.1.8 –1112 15 of 19 trouble-shooting. Problem: the system does not response when transmitter is pressed. Solution: make sure the transmitter in good condition. Ensure that the battery is functioning and the led on the transmitter lights up when button is pressed....
E8 swing automatic gate. Revision 1.1.8 –1112 16 of 19 problem: the gate will open but not close. Solution: check the wire loop is still in place on {ir beam} block between terminal [nc] and [com]. if photobeams are fitted, check beam wiring/setup/ obstructions. Problem: the gate does not travel...
E8 swing automatic gate. Revision 1.1.8 –1112 17 of 19 d1 swing gate wiring diagram for transformer ff important note : transformer, battery and remote receiver must be kept in the control panel box, out of weather 16 v ac mt b mt a 1 2 v + p w r lock n c com 16v ac 0v ac ac 240v main supply to tran...
E8 swing automatic gate. Revision 1.1.8 –1112 18 of 19 limited warranty e8 warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, e8 shall, as its op...
E8 swing automatic gate. Revision 1.1.8 –1112 19 of 19 warning please read carefully important notice an auto gate system cannot prevent burglary. It is only a replacement way for user to open the door. Auto gate systems are generally very reliable but they may not work under all conditions and they...