Garage door opener installation manual please read the manual and the enclosed safety materials carefully! fasten the manual near the garage door after installation. periodic checks of the opener are required to ensure safe operation. the model number label is located on the left side panel ...
2 table of contents introduction....................................................................3 tools needed........................................................................5 assemble the rail................................................................6 garage door opener assembly.....
3 introduction safety symbol and signal word review this garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these safety symbols...
4 5. The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of the header bracket, it may be installed within 4 feet (1.2 m) to the left or right of the door center. See installing the header bracket section..
5 tools needed during assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below..
6 1、assemble the rail to avoid installation difficulties, do not run the garage door opener until instructed to do so. Note: if you choose the three-pieces sectional rail, you may need the following installation instructions. Rail accessories.
7 assemble the rail.
8 assemble the rail 1.1、remove the three rail sections and place them on 1.2、rail connectors installation. 1.3、spread carefully the chain/belt straight inside the rail. Check to be sure the chain is not twisted. Note: make sure the chain engage the 10-tooth sprocket as shown. Rail assembly 1.1、remov...
9 assemble the rail 1.4 screw and lock washer installation. 1.5、tighten the chain 1.5.1 to increase the tension and tighten the chain, turn the tension nut clockwise or adjustable wrench until the nut is spaced properly from the rail end -plate. 1.5.2 once the nut is spaced correctly, any additional...
10 garage door opener assembly hardware.
11 garage door opener assembly.
12 garage door opener assembly 1、fasten the rail to the garage door opener 1.1 place the opener on cardboard or protective surface on floor so opener does not get scratched. Chassis side of opener is facing up. 1.2 position rail onto opener chassis by lining up rail sprocket, make sure shaft insert ...
13 garage door opener assembly 2、determine the header bracket location installation procedures vary according to garage door types. Follow the instructions which apply to your door. 2.1 close the door and mark the inside vertical centerline of the garage door. 2.2 extend the line onto the header wal...
14 garage door opener assembly.
15 3、install the header bracket you can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete ancho...
16 option b ceiling installation 3.1b extend the vertical centerline onto the ceiling as shown. 3.2b center the bracket on the vertical mark, no more than 6" (15 cm) 3.3b from the wall. Make sure the arrow is pointing away from the wall. The bracket can be mounted flush against the ceiling when clea...
17 4、connect the rail to the header bracket align the rail to the header bracket, fasten with the bolts and nuts (h1) (h2) as shown below. Hardware b5 cotter pin Φ2×25(1) b6 shouldered shaft, long Φ8×80(1).
18 5、position the garage door opener note: a 2x4 is ideal for setting the distance between the rail and the door. If the ladder is not tall enough you will need help at this point. If the door hits the trolley when it is raised, pull the trolley release arm down to disconnect the chain connector kit...
19 6、hang the garage door opener.
20 7、attach the emergency release rope and handle note: if it is necessary to cut the emergency release rope, seal the cut end with a match or lighter to prevent unraveling. Ensure that the emergency release rope and handle are above the top of all vehicles to avoid entanglement. 7.1 insert one end ...
21 8、install the door bracket figure 1 shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to create a u- shaped support. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit. Not...
22 a horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, doors with glass panel, etc.) (not provided). A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should ...
23 9、connect the door arm to the trolley hardware option sectional doors note: if the holes in the curved door arm and the straight door arm do not align, reverse the straight door arm, select two holes (as far apart as possible) and attach using bolts (h4) and nuts (h3). 9.1 9.2.
24 9.5 pull the emergency release handle toward the chain/belt connector until they are connected, you will hear a click. Note: if the straight door arm is hanging down too far, you may cut 6 inches (15 cm) from the solid end. 9.4 9.2 attach the curved door arm to the door bracket using the shoulder...
25 10、install the wall control introduction install the wall control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from the moving parts of the door. Your product may look different than the illustrations. Note: for gang box installations ...
26 a b c.
27 wall control battery replacement c a a a b a.
28 11、 wire the wall control to the garage door opener 11.1 strip 7/16 inch (11 mm) of insulation from one end of the wire and separate the wires. 11.2 connect the white wire to the gnd terminal and the red\white wire to the pbsw terminal on garage door opener..
29 12、 attach the warning labels 12.1 attach the entrapment warning label on the wall near the door control with tacks or staples. 12.2 attach the manual release/safety reverse test label in a visible location on the inside of the garage door. Install the photo eye safety system introduction importa...
30 the sending sensor (with a red led) transmits an invisible light beam to the receiving sensor (with a green led). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to the full open position, and the garage door opener lights will flash three minutes...
31 install the photo eye safety system 1、install the safety reversing sensors the safety reversing sensors can be attached to the wall, the sensors should be no more than 6 inches (15 cm) above the floor. Position the mounting bracket against the wall with the curved arms facing the door. Make sure ...
32 insert the white wires into the gnd terminal on the garage door opener. Insert the white/red wires into the pb terminal on the garage door opener. Ensure the safety reversing sensors are aligned the door will not close if the sensors have not been installed and aligned correctly. When the light b...
33 power connect power.
34 adjustments.
35 programming and adjustment a) programming buttons b) preparation: move the door to lock the trolley so that the opener can drive the door when adjustment. C) connect power: puts through the power source, the led display from “9” to “1”. If the number direction displayed on led is opposite, press ...
36 d) program the travel note: the up and down buttons can be used to move the door up and down as needed..
37 e) remote control program a remote using the code button note: repeat up steps to code a maximum of 20 different remote controls. To open or close the garage door, press and hold button. When the garage door move, release button. To stop garage door during travel, press and hold button until door...
38 f) to erase the memory press and hold the code button on garage door opener, the “●” will turn on. Release the code button when the “●” turns off. All remote control are now erased. Reprogram any accessory you wish to use..
39 g) the adjustment of reverse force the “close” position force sensitivity.
40 close door automatically screen 1 2 3 4 5 6 7 8 9 minute 1 2 3 4 5 6 7 8 9 note: the screen shows “0”, press button “setting” to confirm, at this time cancel automatically closing function. Automatically door closing function is effective only under the complete open of the door, so if you want t...
41 h) circuit board.
42 i) use photoelectric switches the user can simply push a button to set or cancel the photoelectric switch function..
43 turn off light automatically it has turned off light function so do not need to set. When the opener is running, the light is brighten automatically .If have no wall switch and press any button in 3 minutes, the light will be off automatically. Power failure clutch lock if your garage door is in ...
44 door within a door maintenance and repair check the safety protection function of the opener at least one month regularly whether the closing state changed , it is sensitive for error recognition ,the door is keep balance and adjust in time, so as to keep the best state,. It is necessary for find...
45 trouble shooting.
