1. DL manuals
  2. National Instruments
  3. Control Unit
  4. NI 9220
  5. Getting Started Manual

National Instruments NI 9220 Getting Started Manual

Manual is about: Voltage Output Module/16 AO, ±10 V, 16 Bit, 25 kS/s/ch Simultaneous

Summary of NI 9220

  • Page 1

    Getting started guide ni 9264 16 ao, ±10 v, 16 bit, 25 ks/s/ch simultaneous.

  • Page 2: Note

    This document explains how to connect to the ni 9264. In this document, the ni 9264 with spring terminal and the ni 9264 with dsub are referred to inclusively as the ni 9264. Note before you begin, complete the software and hardware installation procedures in your chassis documentation. Note the gui...

  • Page 3: Hazardous Voltage

    Way. If the product is damaged, return it to ni for repair. Hazardous voltage this icon denotes a warning advising you to take precautions to avoid electrical shock. Safety guidelines for hazardous voltages you can connect hazardous voltages only to the ni 9264 with spring terminal. Do not connect h...

  • Page 4: Note

    Note when module terminals are hazardous voltage live (>42.4 vpk/60 vdc), you must ensure that devices and circuits connected to the module are properly insulated from human contact. You must use the ni 9940 connector backshell kit with the ni 9264 with spring terminal to ensure that the terminals a...

  • Page 5: Caution

    Caution do not connect the ni 9264 to signals or use for measurements within measurement categories iii or iv. Ni 9264 with dsub safety voltages isolation channel-to-channel none channel-to-earth ground continuous 60 vdc, measurement category i withstand 1,000 vrms, verified by a 5 s dielectric with...

  • Page 6: Caution

    Caution do not connect the ni 9264 to signals or use for measurements within measurement categories ii, iii, or iv. Note measurement categories cat i and cat o are equivalent. These test and measurement circuits are not intended for direct connection to the mains building installations of measuremen...

  • Page 7: Caution

    Caution do not remove modules unless power has been switched off or the area is known to be nonhazardous. Caution substitution of components may impair suitability for class i, division 2. Caution for division 2 and zone 2 applications, install the system in an enclosure rated to at least ip54 as de...

  • Page 8: Caution

    An ni chassis that has been evaluated as ex nc iic t4, ex iic t4, ex na iic t4, or ex nl iic t4 equipment. Caution you must make sure that transient disturbances do not exceed 140% of the rated voltage. Caution the system shall only be used in an area of not more than pollution degree 2, as defined ...

  • Page 9: Caution

    When the product is operated in the intended operational electromagnetic environment. This product is intended for use in industrial locations. However, harmful interference may occur in some installations, when the product is connected to a peripheral device or test object, or if the product is use...

  • Page 10: Caution

    For the lr certificate, or look for the lloyd’s register mark on the product. Caution in order to meet the emc requirements for marine applications, install the product in a shielded enclosure with shielded and/or filtered power and input/output ports. In addition, take precautions when designing, s...

  • Page 12

    Ni 9264 pinout ao0 ao1 ao2 ao3 ao4 ao5 ao6 ao7 ao8 ao9 ao10 ao11 ao12 ao13 ao14 ao15 com com com com com com com com com com com com com com com com com com com com 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 com com com com com com com com nc n...

  • Page 14

    Ni 9264 connection guidelines make sure that devices you connect to the ni 9264 are compatible with the module specifications. Connecting to a spring-terminal connector what to use • ni 9264 spring-terminal connector • 0.08 mm 2 to 1.0 mm 2 (28 awg to 18 awg) copper conductor wire with 7 mm (0.28 in...

  • Page 16: Note

    High-vibration application connections if your application is subject to high vibration, ni recommends that you use the ni 9940 backshell kit to protect connections to the ni 9264 with spring terminal. Overvoltage protection the ni 9264 provides overvoltage protection for each channel. Note refer to...

  • Page 17: Compactrio

    Where to go next compactrio ni compactdaq located atni.Com/manuals related information c series documentation & resources ni.Com/info cseriesdoc services ni.Com/services installs with the software ni 9264 datasheet ni-rio help labview fpga help ni 9264 datasheet ni-daqmx help labview help ni 9264 ge...

  • Page 18

    Worldwide support and services the ni website is your complete resource for technical support. At ni.Com/support , you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from ni application engineers. Visit ni.Com/services for...

  • Page 19

    Ni corporate headquarters is located at 11500 north mopac expressway, austin, texas, 78759-3504. Ni also has offices located around the world. For telephone support in the united states, create your service request at ni.Com/support or dial 1 866 ask myni (275 6964). For telephone support outside th...

  • Page 20

    Refer to the ni trademarks and logo guidelines at ni.Com/trademarks for information on ni trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering ni products/technology, refer to the appropriate location: help»pat...