Operating instructions and specifications ni 9222/9223 4-channel, ±10 v, 16-bit simultaneous, channel-to-channel isolated analog input modules ni.Com/manuals deutsch français.
Ni 9222/9223 2 ni.Com this document describes how to use the national instruments 9222 and national instruments 9223 and includes specifications and terminal assignments for the ni 9222 and ni 9223. In this document, the ni 9222 and ni 9223 are referred to inclusively as the ni 9222/9223.Visit ni.Co...
© national instruments corp. 3 ni 9222/9223 safety guidelines operate the ni 9222/9223 only as described in these operating instructions. Hot surface this icon denotes that the component may be hot. Touching this component may result in bodily injury. Safety guidelines for hazardous locations the ni...
Ni 9222/9223 4 ni.Com caution substitution of components may impair suitability for class i, division 2. Caution for zone 2 applications, install the system in an enclosure rated to at least ip 54 as defined by iec 60529 and en 60529. Special conditions for hazardous locations use in europe this equ...
© national instruments corp. 5 ni 9222/9223 electromagnetic compatibility guidelines this product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (emc) as stated in the product specifications. These requirements and limits are designed to provide...
Ni 9222/9223 6 ni.Com caution emissions that exceed the regulatory requirements may occur when this product is connected to a test object. Caution changes or modifications not expressly approved by national instruments could void the user’s authority to operate the hardware under the local regulator...
© national instruments corp. 7 ni 9222/9223 connecting the ni 9222/9223 the ni 9222/9223 provides connections for four simultaneously sampled, isolated analog input channels. Figure 1. Ni 9222/9223 terminal assignments ai0+ ai0– ai1+ ai1– ai2+ ai2– ai3+ ai3– 0 1 0 1 0 1 0 1.
Ni 9222/9223 8 ni.Com caution electrostatic discharge (esd) can damage this product. To prevent damage, use industry-standard esd prevention measures during installation, maintenance, and operation. The ni 9222/9223 has four 2-terminal detachable screw-terminal connectors. Note you must use 2-wire f...
© national instruments corp. 9 ni 9222/9223 figure 2. Connecting a grounded signal source to the ni 9222/9223 figure 3. Connecting a floating signal source to the ni 9222/9223 ni 9222/9223 signal source ai– + – ai+ ni 9222/9223 signal source ai– + – ai+.
Ni 9222/9223 10 ni.Com the ni 9222/9223 analog input channels are floating with respect to earth ground and each other. The incoming analog signal on each channel is buffered, conditioned, and then sampled by a 16-bit successive approximation register adc. Each channel provides an independent signal...
© national instruments corp. 11 ni 9222/9223 wiring for high-vibration applications if an application is subject to high vibration, national instruments recommends that you either use ferrules to terminate wires to the detachable screw-terminal connector or use the ni 9971 backshell kit to protect t...
Ni 9222/9223 12 ni.Com sleep mode this module supports a low-power sleep mode. Support for sleep mode at the system level depends on the chassis that the module is plugged into. Refer to the chassis manual for information about support for sleep mode. If the chassis supports sleep mode, refer to the...
© national instruments corp. 13 ni 9222/9223 input characteristics number of channels.......................... 4 analog input channels adc resolution................................. 16 bits type of adc..................................... Successive approximation register (sar) input voltage range...
Ni 9222/9223 14 ni.Com maximum sampling rate module compactdaq rio ni-daqmx fpga user-controlled i/o sampling* fpga i/o nodes ni 9222 500 ks/s 500 ks/s 300 ks/s ni 9223 1 ms/s 1 ms/s 350 ks/s * fpga user-controlled i/o sampling provides low level access to sample acquisition and transfer, and higher...
© national instruments corp. 15 ni 9222/9223 accuracy stability gain drift .................................... 6 ppm/°c offset drift .................................. 29 μv/°c cmrr (f in = 60 hz) .......................... 100 db –3 db bandwidth ni 9222....................................... >500 ...
Ni 9222/9223 16 ni.Com noise ................................................. 0.75 lsb rms total harmonic distortion (thd) (20 v pp at 10 khz) ............................ –85 db crosstalk (20 v pp at 1 khz) .............. –100 db mtbf ............................................... Contact ni for ...
© national instruments corp. 17 ni 9222/9223 physical characteristics if you need to clean the module, wipe it with a dry towel. Note for two-dimensional drawings and three-dimensional models of the c series module and connectors, visit ni.Com/dimensions and search by module number. Screw-terminal w...
Ni 9222/9223 18 ni.Com safety safety voltages connect only voltages that are within the following limits. Isolation channel-to-channel continuous ........................... 60 vdc, measurement category i withstand ............................. 1000 v rms , verified by a 5 s dielectric withstand tes...
© national instruments corp. 19 ni 9222/9223 measurement category i is for measurements performed on circuits not directly connected to the electrical distribution system referred to as mains voltage. Mains is a hazardous live electrical supply system that powers equipment. This category is for meas...
Ni 9222/9223 20 ni.Com safety standards this product meets the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: • iec 61010-1, en 61010-1 • ul 61010-1, csa 61010-1 note for ul and other safety certifications, refer to the produc...
© national instruments corp. 21 ni 9222/9223 caution when operating this product, use shielded cables and accessories. Note for emc declarations and certifications, refer to the online product certification section. Ce compliance this product meets the essential requirements of applicable european d...
Ni 9222/9223 22 ni.Com shock and vibration to meet these specifications, you must panel mount the system and either affix ferrules to the ends of the terminal wires or use the ni 9971 backshell kit to protect the connections. Operating vibration random (iec 60068-2-64)......... 5 g rms , 10 to 500 h...
© national instruments corp. 23 ni 9222/9223 ingress protection.............................. Ip 40 operating humidity (iec 60068-2-56).............................. 10 to 90% rh, noncondensing storage humidity (iec 60068-2-56).............................. 5 to 95% rh, noncondensing maximum altitud...
Ni 9222/9223 24 ni.Com waste electrical and electronic equipment (weee) eu customers at the end of the product life cycle, all products must be sent to a weee recycling center. For more information about weee recycling centers, national instruments weee initiatives, and compliance with weee directiv...
© national instruments corp. 25 ni 9222/9223 where to go for support the national instruments web site is your complete resource for technical support. At ni.Com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assistance f...
Ni 9222/9223 26 ni.Com korea 82 02 3451 3400, lebanon 961 (0) 1 33 28 28, malaysia 1800 887710, mexico 01 800 010 0793, netherlands 31 (0) 348 433 466, new zealand 0800 553 322, norway 47 (0) 66 90 76 60, poland 48 22 328 90 10, portugal 351 210 311 210, russia 7 495 783 6851, singapore 1800 226 588...
© 2010 national instruments corp. All rights reserved. 374223a-01 aug10 labview, national instruments, ni, ni.Com, the national instruments corporate logo, and the eagle logo are trademarks of national instruments corporation. Refer to the trademark information at ni.Com/trademarks for other nationa...
