- DL manuals
- National Instruments
- Measuring Instruments
- NI 9263
- Operating Instructions Manual
National Instruments NI 9263 Operating Instructions Manual
Summary of NI 9263
Page 1
Operating instructions and specifications ni 9263 4-channel, ± 10 v, 16-bit analog voltage output module ni.Com/manuals deutsch français.
Page 2
Ni 9263 operating instructions and specifications 2 ni.Com this doc u ment describes how to u se the national instr u ments 9263 and incl u des specifications and terminal assignments for the ni 9263. Visit ni.Com/info and enter rd s oftwarever s ion to determine which software yo u need for the mod...
Page 3
© national instruments corp. 3 ni 9263 operating instructions and specifications safety guidelines for hazardous voltages if hazardo u s voltages are connected to the mod u le, take the following preca u tions. A hazardo u s voltage is a voltage greater than 42.4 v pk or 60 vdc to earth gro u nd. Ca...
Page 4
Ni 9263 operating instructions and specifications 4 ni.Com fig u re 1 shows the ni 9932 connector backshell. Figure 1. Ni 9932 connector backshell safety guidelines for hazardous locations the ni 9263 is s u itable for u se in class i, division 2, gro u ps a, b, c, d, t4 hazardo u s locations; class...
Page 5
© national instruments corp. 5 ni 9263 operating instructions and specifications caution do not disconnect i/o-side wires or connectors u nless power has been switched off or the area is known to be nonhazardo u s. Caution do not remove mod u les u nless power has been switched off or the area is kn...
Page 6
Ni 9263 operating instructions and specifications 6 ni.Com special conditions for marine applications some mod u les are lloyd’s register (lr) type approved for marine applications. To verify lloyd’s register certification, visit ni.Com/certification and search for the lr certificate, or look for th...
Page 7
© national instruments corp. 7 ni 9263 operating instructions and specifications connecting the ni 9263 the ni 9263 has a 10-terminal, detachable screw-terminal connector that provides connections for 4 analog o u tp u t channels. Figure 2. Ni 9263 terminal assignments ao0 com ao1 com ao2 com ao3 co...
Page 8
Ni 9263 operating instructions and specifications 8 ni.Com each channel of the ni 9263 has an ao terminal to which yo u can connect the positive lead of a load. Each channel also has a common terminal, com, and there is an additional com terminal at the bottom of the connector. All of the com termin...
Page 9
© national instruments corp. 9 ni 9263 operating instructions and specifications each channel has a digital-to-analog converter (dac) that prod u ces a voltage signal. Each channel also has overvoltage and short-circ u it protection. Refer to the specifications section for more information abo u t t...
Page 10
Ni 9263 operating instructions and specifications 10 ni.Com wiring for high-vibration applications if an application is s u bject to high vibration, national instr u ments recommends that yo u either u se ferr u les to terminate wires to the detachable screw-terminal connector or u se the ni 9932 ba...
Page 11
© national instruments corp. 11 ni 9263 operating instructions and specifications sleep mode this mod u le s u pports a low-power sleep mode. S u pport for sleep mode at the system level depends on the chassis that the mod u le is pl u gged into. Refer to the chassis man u al for information abo u t...
Page 12
Ni 9263 operating instructions and specifications 12 ni.Com specifications the following specifications are typical for the range –40 to 70 °c u nless otherwise noted. All voltages are relative to com u nless otherwise noted. Output characteristics n u mber of channels.......................... 4 an...
Page 13
© national instruments corp. 13 ni 9263 operating instructions and specifications c u rrent drive ..................................... ±1 ma per channel max o u tp u t impedance............................. 0.1 Ω acc u racy stability gain drift .................................... 6 ppm/°c offset d...
Page 14
Ni 9263 operating instructions and specifications 14 ni.Com update time noise ................................................. 260 μ v rms slew rate ........................................... 4 v/ μ s crosstalk ........................................... 76 db settling time (100 pf load, to 1 lsb)...
Page 15
© national instruments corp. 15 ni 9263 operating instructions and specifications capacitive drive ................................ 1,500 pf min monotonicity..................................... 16 bits dnl .................................................. –1 to 2 lsbs max inl (endpoint) .............
Page 16
Ni 9263 operating instructions and specifications 16 ni.Com physical characteristics if yo u need to clean the mod u le, wipe it with a dry towel. Note for two-dimensional drawings and three-dimensional models of the c series mod u le and connectors, visit ni.Com/dimen s ion s and search by mod u le...
Page 17
© national instruments corp. 17 ni 9263 operating instructions and specifications safety safety voltages connect only voltages that are within the following limits. Isolation channel-to-channel .................... None channel-to-earth gro u nd contin u o u s ........................... 250 v rms ,...
Page 18
Ni 9263 operating instructions and specifications 18 ni.Com hazardous locations u.S. (ul) .......................................... Class i, division 2, gro u ps a, b, c, d, t4; class i, zone 2, aex na iic t4 canada (c-ul) ................................. Class i, division 2, gro u ps a, b, c, d, ...
Page 19
© national instruments corp. 19 ni 9263 operating instructions and specifications electromagnetic compatibility this prod u ct meets the req u irements of the following emc standards for electrical eq u ipment for meas u rement, control, and laboratory u se: • en 61326 (iec 61326): class a emissions...
Page 20
Ni 9263 operating instructions and specifications 20 ni.Com ce compliance this prod u ct meets the essential req u irements of applicable e u ropean directives as follows: • 2006/95/ec; low-voltage directive (safety) • 2004/108/ec; electromagnetic compatibility directive (emc) online product certifi...
Page 21
© national instruments corp. 21 ni 9263 operating instructions and specifications operating shock (iec 60068-2-27).............................. 30 g, 11 ms half sine, 50 g, 3 ms half sine, 18 shocks at 6 orientations environmental national instr u ments c series mod u les are intended for indoor u ...
Page 22
Ni 9263 operating instructions and specifications 22 ni.Com maxim u m altit u de............................. 2,000 m poll u tion degree (iec 60664) .......... 2 environmental management national instr u ments is committed to designing and man u fact u ring prod u cts in an environmentally responsib...
Page 23
© national instruments corp. 23 ni 9263 operating instructions and specifications calibration yo u can obtain the calibration certificate and information abo u t calibration services for the ni 9263 at ni.Com/calibration . Calibration interval ........................... 1 year ⬉ᄤֵᙃѻક∵ᶧࠊㅵ⧚ࡲ⊩ ˄Ё ro...
Page 24
Ni 9263 operating instructions and specifications 24 ni.Com where to go for support the national instr u ments web site is yo u r complete reso u rce for technical s u pport. At ni.Com/ s upport yo u have access to everything from tro u bleshooting and application development self-help reso u rces t...
Page 25
© national instruments corp. 25 ni 9263 operating instructions and specifications korea 82 02 3451 3400, lebanon 961 (0) 1 33 28 28, malaysia 1800 887710, mexico 01 800 010 0793, netherlands 31 (0) 348 433 466, new zealand 0800 553 322, norway 47 (0) 66 90 76 60, poland 48 22 328 90 10, port u gal 3...
Page 26
© 2004–2009 national instruments corp. All rights reserved. 373781d-01 feb09 national instruments, ni, ni.Com, and labview are trademarks of national instruments corporation. Refer to the terms of use section on ni.Com/legal for more information about national instruments trademarks. Other product a...