- DL manuals
- National Instruments
- Network Card
- NI 9474
- Operating Instructions Manual
National Instruments NI 9474 Operating Instructions Manual - page 31
© 2003–2008 National Instruments Corp. All rights reserved.
373509E-01
May08
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the
Terms of Use
section on
ni.com/legal
for more information about National Instruments trademarks. Other
product and company names mentioned herein are trademarks or trade names of their respective companies.
For patents covering National Instruments products, refer to the appropriate location:
Help»Patents
in your software,
the
patent
s
.txt
file on your media, or
ni.com/patent
s
.
Summary of NI 9474
Page 1
Operating instructions and specifications ni 9472/9474 8-channel digital output modules ni.Com/manuals deutsch français.
Page 2
Ni 9472/9474 2 ni.Com this doc u ment describes how to u se the national instr u ments 9472 and national instr u ments 9474 and incl u des specifications and terminal or pin assignments. In this doc u ment, the ni 9472/9474 with screw terminal and ni 9472 with dsub are referred to incl u sively as t...
Page 3
© national instruments corp. 3 ni 9472/9474 hot surface this icon denotes that the component may be hot. To u ching this component may res u lt in bodily inj u ry. Safety guidelines for hazardous voltages yo u can connect hazardo u s voltages only to the ni 9472/9474 with screw terminal. Do not conn...
Page 4
Ni 9472/9474 4 ni.Com and circ u its connected to the mod u le are properly ins u lated from h u man contact. Yo u m u st u se the ni 9932 connector backshell kit to ens u re that the terminals are not accessible. Fig u re 1 shows the ni 9932 connector backshell. Note yo u can u se the ni 9932 conne...
Page 5
© national instruments corp. 5 ni 9472/9474 safety guidelines for hazardous locations the ni 9472/9474 is s u itable for u se in class i, division 2, gro u ps a, b, c, d, t4 hazardo u s locations; class i, zone 2, aex nc iic t4 and ex nc iic t4 hazardo u s locations; and nonhazardo u s locations onl...
Page 6
Ni 9472/9474 6 ni.Com caution for zone 2 applications, install a protection device between the v s u p and com terminals on the ni 9472/9474. The device m u st prevent the inp u t v s u p -to-com voltage from exceeding 42 v if there is a transient overvoltage condition. Special conditions for hazard...
Page 7
© national instruments corp. 7 ni 9472/9474 special conditions for marine applications some mod u les are lloyd’s register (lr) type approved for marine applications. To verify lloyd’s register certification, visit ni.Com/certification and search for the lr certificate, or look for the lloyd’s regis...
Page 8
Ni 9472/9474 8 ni.Com connecting the ni 9472/9474 the ni 9472/9474 provides connections for eight digital o u tp u t channels. Figure 2. Ni 9472/9474 terminal and pin assignments do0 do1 do2 do3 do4 do5 do6 do7 vsup com 0 1 2 3 4 5 6 7 8 9 com vsup com com vsup com com vsup com com vsup com com do0 ...
Page 9
© national instruments corp. 9 ni 9472/9474 the ni 9472/9474 with screw terminal has a 10-terminal, detachable screw-terminal connector. The ni 9472 with dsub has a 25-pin dsub connector. Each channel of the ni 9472/9474 has a terminal or pin, do, to which yo u can connect a device. The eight digita...
Page 10
Ni 9472/9474 10 ni.Com yo u m u st connect an external power s u pply to the ni 9472/9474. This power s u pply provides the c u rrent for the devices yo u connect to the mod u le. Connect the positive lead of the power s u pply to v s u p and the negative lead of the power s u pply to com. The v s u...
Page 11
© national instruments corp. 11 ni 9472/9474 yo u can directly connect the ni 9472/9474 to a variety of ind u strial devices s u ch as solenoids, motors, act u ators, relays, and lamps. Make s u re the devices yo u connect to the ni 9472/9474 are compatible with the o u tp u t specifications of the ...
Page 12
Ni 9472/9474 12 ni.Com increasing current drive each channel of the ni 9472 has a contin u o u s o u tp u t c u rrent of 0.75 a, and each channel of the ni 9474 has a contin u o u s o u tp u t c u rrent of 1 a. If yo u want to increase the o u tp u t c u rrent to a device, yo u can connect any n u m...
Page 13
© national instruments corp. 13 ni 9472/9474 wiring for high-vibration applications if an application u sing the ni 9472/9474 with screw terminal is s u bject to high vibration, national instr u ments recommends that yo u either u se ferr u les to terminate wires to the detachable screw-terminal con...
Page 14
Ni 9472/9474 14 ni.Com i/o protection the ni 9472/9474 is short-circ u it proof in accordance with iec 1131-2 and provides overc u rrent protection. Understanding short-circuit-proof devices each channel on the ni 9472/9474 has circ u itry that protects it from c u rrent s u rges res u lting from sh...
Page 15
© national instruments corp. 15 ni 9472/9474 more information abo u t the maxim u m contin u o u s o u tp u t c u rrent, short-circ u it behavior, and short-circ u it trip time. Yo u also can refer to the iec 1131-2 standard for more information abo u t short-circ u it-proof devices. Tip beca u se t...
Page 16
Ni 9472/9474 16 ni.Com the channel is in an overc u rrent state, meas u re the voltage between do and v s u p . If the voltage is eq u al to the voltage of the external power s u pply connected to the mod u le, the channel is in an overc u rrent state. Resetting channels after an overcurrent conditi...
Page 17
© national instruments corp. 17 ni 9472/9474 typically, when a system is in sleep mode, yo u cannot comm u nicate with the mod u les. In sleep mode, the system cons u mes minimal power and may dissipate less heat than it does in normal mode. Refer to the specifications section for more information a...
Page 18
Ni 9472/9474 18 ni.Com o u tp u t impedance ( r 0 ) typical ........................................ 0.07 Ω maxim u m ................................... 0.13 Ω contin u o u s o u tp u t c u rrent ( i 0 ), per channel ni 9472....................................... 0.75 a max ni 9474....................
Page 19
© national instruments corp. 19 ni 9472/9474 o u tp u t delay time (f u ll load) ni 9472....................................... 100 μ s max ni 9474....................................... 1 μ s max mtbf ni 9472....................................... 1,113,301 ho u rs at 25 °c; bellcore iss u e 2, met...
Page 20
Ni 9472/9474 20 ni.Com thermal dissipation (at 70 °c) active mode ............................... 1.5 w max sleep mode ................................. 55 mw max ni 9474 power requirements power cons u mption from chassis active mode ............................... 660 mw max sleep mode ..............
Page 21
© national instruments corp. 21 ni 9472/9474 ferr u les ............................................. 0.25 mm 2 to 2.5 mm 2 weight ni 9472/9474 with screw terminal ............................ 150 g (5.3 oz) ni 9472 with dsub ................... 145 g (5.1 oz) safety ni 9472/9474 with screw terminal...
Page 22
Ni 9472/9474 22 ni.Com this category refers to local-level electrical distrib u tion, s u ch as that provided by a standard wall o u tlet, for example, 115 v for u.S. Or 230 v for e u rope. Caution do not connect the ni 9472/9474 with screw terminal to signals or u se for meas u rements within meas ...
Page 23
© national instruments corp. 23 ni 9472/9474 s u pply system that powers eq u ipment. This category is for meas u rements of voltages from specially protected secondary circ u its. S u ch voltage meas u rements incl u de signal levels, special eq u ipment, limited-energy parts of eq u ipment, circ u...
Page 24
Ni 9472/9474 24 ni.Com hazardous locations u.S. (ul) .......................................... Class i, division 2, gro u ps a, b, c, d, t4; class i, zone 2, aex nc iic t4 canada (c-ul) ................................. Class i, division 2, gro u ps a, b, c, d, t4; class i, zone 2, ex nc iic t4 e u...
Page 25
© national instruments corp. 25 ni 9472/9474 environmental national instr u ments c series mod u les are intended for indoor u se only b u t may be u sed o u tdoors if installed in a s u itable enclos u re. Refer to the man u al for the chassis yo u are u sing for more information abo u t meeting th...
Page 26
Ni 9472/9474 26 ni.Com shock and vibration to meet these specifications, yo u m u st panel mo u nt the system. If yo u are u sing the ni 9472/9474 with screw terminal, yo u also m u st either affix ferr u les to the ends of the terminal wires or u se the ni 9932 backshell kit to protect the connecti...
Page 27
© national instruments corp. 27 ni 9472/9474 note for emc compliance, operate this device with shielded cabling. Ce compliance this prod u ct meets the essential req u irements of applicable e u ropean directives, as amended for ce markings, as follows: • 2006/95/ec; low-voltage directive (safety) •...
Page 28
Ni 9472/9474 28 ni.Com environmental management national instr u ments is committed to designing and man u fact u ring prod u cts in an environmentally responsible manner. Ni recognizes that eliminating certain hazardo u s s u bstances from o u r prod u cts is beneficial not only to the environment ...
Page 29
© national instruments corp. 29 ni 9472/9474 where to go for support the national instr u ments web site is yo u r complete reso u rce for technical s u pport. At ni.Com/ s upport yo u have access to everything from tro u bleshooting and application development self-help reso u rces to email and pho...
Page 30
Ni 9472/9474 30 ni.Com telephone s u pport o u tside the united states, contact yo u r local branch office: a u stralia 1800 300 800, a u stria 43 662 457990-0, belgi u m 32 (0) 2 757 0020, brazil 55 11 3262 3599, canada 800 433 3488, china 86 21 5050 9800, czech rep u blic 420 224 235 774, denmark ...
Page 31
© 2003–2008 national instruments corp. All rights reserved. 373509e-01 may08 national instruments, ni, ni.Com, and labview are trademarks of national instruments corporation. Refer to the terms of use section on ni.Com/legal for more information about national instruments trademarks. Other product a...